2007 FORD FIESTA air conditioning

Engine - I .25L Duratec-1 6V (Sigma)llm4L
303-01A-45 Duratec-1 6V (Sigma)/l .6L Duratec-1 6V (Sigma) 303-01 A-45
IN-VEHICLE REPAIR
lnstall the engine front mount.
27. Remove the
trolley jack.
28. Attach the generator.
1. lnstall the stud and nut.
2. lnstall the bolt.
3. Tighten the bolt.
31. lnstall the timing belt upper cover retaining
bolts.
32. N0TE:Do not tighten the coolant pump
pulley retaining bolts at this stage.
lnstall the coolant pump pulley.
I 33. lnstall the accessory drive belt.
29. Connect the generator electrical connector.
For additional information, refer to:
Accessory Drive
Belt - 1.4L Duratec-1 6V
(Sigma)ll.GL Duratec-1 6V (Sigma),
Vehicles With: Air Conditioning (303-05
Accessory Drive,
Removal and
Installation).
30. Raise and support the vehicle.
For additional information, refer to: Lifting
(100-02 Jacking and Lifting, Description
and Operation).
2006.0 Fiesta 1212006 GI 83738en
procarmanuals.com

Engine - 1.25L Duratec-1 6V (Sigma)llm4L
303-01 A-66 Duratec-1 6V (Sigma)/l.GL Duratec-1 6V (Sigma) 303-01 A-66
IN-VEHICLE REPAIR
Oil Pump(21 714 0)
Special Tool(s)
Removal
1. Remove the timing belt.
For additional information, refer to Timing
Belt in this section.
2. Remove the crankshaft timing belt pulley.
3. Detach the air conditioning (AIC) compressor
from the cylinder block and position
it to one
side.
4. Remove the oil pan.
For additional information, refer to Oil Pan
in this section.
5. Detach the oil pick-up tube from the oil pump
and remove the oil pump (engine shown
removed for clarity).
Discard the gaskets.
Remove and discard the crankshaft front oil
seal.
Installation
1. N0TE:lnstall a new oil pump gasket.
Install the oil pump (engine shown removed
for clarity).
2. N0TE:lnstall a new oil pump intake pipe
gasket.
2006.0 Fiesta 1212006 GI 83742en
procarmanuals.com

Engine - 1.25L Duratec-1 6V (Sigma)llI4L
303-01 A-67 Duratec-1 6V (Sigma)/l .6L Duratec-1 6V (Sigma) 303-01 A-67
IN-VEHICLE REPAIR
Attach the oil pick-up tube to the oil pump 6. Install the crankshaft timing belt pulley.
(engine shown removed for clarity).
7. Install the timing belt.
3. N0TE:lnstall a new crankshaft front oil seal.
For additional information, refer to Timing
Using the special tool, install the crankshaft Belt
in this section.
front oil seal.
4. Install the oil pan.
For additional information, refer to Oil Pan
in this section.
5. Attach the air conditioning (AIC) compressor
to the cylinder block.
2006.0 Fiesta 1212006 GI 83742en
procarmanuals.com

Engine - 1.25L Duratec-1 6V (Sigma)lIl4L
Duratec-1 6V (Sigma)ll .6L Duratec-1 6V (Sigma)
REMOVAL
19. Disconnect the EVAP electrical connector. 22.
Disconnect the knock sensor (KS) electrical
connector.
20. Disconnect the low pressure evaporate
emission (EVAP) hose from the EVAP valve. 23.
Disconnect the generator electrical
connectors.
21. Detach the brake booster vacuum line from
the intake manifold. 24.
Remove the right-hand
headlamp assembly.
For additional information, refer to:
Headlamp Assembly (41 7-01 Exterior
Lighting, Removal and Installation).
25. Disconnect the air conditioning
(AIC)
lower-pressure cut-off switch electrical
connector.
2006.0 Fiesta 1212006 GI 131 63en
procarmanuals.com

Engine - 1.25L Duratec-1 6V (Sigma)ll.4L
303-01 A-76 Duratec-1 6V (Sigma)lll6L Duratec-1 6V (Sigma) 303-01 A-76
REMOVAL
Support the exhaust flexible pipe with a
suitable support wrap or suitable splint. 43.
Detach the power steering line support
bracket from the engine block.
/' -
40. Detach the exhaust flexible pipe from the
44. Disconnect the power steering line from
catalytic converter. the steering pump.
Discard the nuts and the gasket.
Allow the fluid to drain into a suitable
container.
41. Remove the accessory drive belt.
For additional information, refer to: 45.
Using the special tool, detach the power
Accessory Drive Belt
- I .4L Duratec-16V steering line from the power steering pump.
(Sigma)ll.GL Duratec-1 6V (Sigma), Allow the fluid to drain into a suitable
Vehicles With: Air Conditioning (303-05 container.
Accessory Drive, Removal and
Installation).
42. Detach the
AIC compressor from the
cylinder block and position
it to one side.
2006.0 Fiesta 1212006 GII 31 63en
procarmanuals.com

Engine - 1.25L Duratec-1 6V (Sigma)ll.4L
303-01 A-89 Duratec-1 6V (Sigma)ll.GL Duratec-1 6V (Sigma) 303-01 A-89
REMOVAL
44m ACAUTION:~~~~ bending of the exhaust Vehicles with air conditioning
I flexible pipe may cause damage resulting 47.
Disconnect the air conditioning (NC)
, in failure. low-pressure cutoff switch electrical
Support the exhaust
flexible pipe with a connector.
suitable support
wrap or suitable splint.
48. Disconnect the NC compressor clutch
45. Detach the exhaust flexible pipe from the electrical connector.
catalytic converter.
Discard the nuts and the gasket.
46. Remove the accessory drive belt.
For additional information, refer to:
Accessory Drive
Belt - I .4L Duratec-I 6V
(Sigma)ll .6L Duratec-1 6V (Sigma),
Vehicles With: Air Conditioning (303-05
Accessory Drive, Removal and
Installation)
I Accessory Drive Belt - I .4L Duratec-I 6V
(Sigma)ll .6L Duratec-1 6V (Sigma),
Vehicles Without: Air Conditioning
(303-05 Accessory Drive,
Removal and
Installation).
49. Disconnect the NC high-pressure cutoff
switch
electrical connector.
2006.0 Fiesta 1212006 G380458en
procarmanuals.com

303-01 A-I 26 Engine
- 1.25L Duratec-I 6V (Sigma)ll.4L
Duratec-1 6V (Sigma)ll .6L
Duratec-1 6V (Sigma) 303-01A-I26
INSTALLATION
23. Attach the air conditioning (NC)
compressor to the
cylinder block.
27. Connect the reversing lamp switch
electrical connector.
I
24. Connect the NC compressor clutch
28. Connect the crankshaft position (CKP)
electrical connector. sensor electrical connector.
25. Install the accessory drive belt. 29. Connect the oil pressure switch electrical
For
additional information, refer to: connector.
Accessory Drive
Belt - I .4L Duratec-16V
(Sigma)ll .6L Duratec-1 6V (Sigma),
Vehicles With: Air Conditioning (303-05
Accessory Drive,
Removal and
Installation).
26. Connect the starter motor electrical
connectors.
30.
N0TE:lnstall new exhaust flange nuts and
a new exhaust
flange gasket.
2006.0 Fiesta 1212006 Gll3164en
procarmanuals.com

303-01 A-I 29 Engine
- 1.25L Duratec-I
6V (Sigma)ll.4L
Duratec-I 6V (Sigma)/l .6L Duratec-1 6V (Sigma) 303-01A-129
INSTALLATION
45. Attach the power steering line to the power 48.
Connect the engine coolant temperature
i steering pump mounting bracket. (ECT) sensor electrical connector.
46, Install the engine wiring harness support 49.
Connect the generator electrical
brackets. connectors.
Connect the engine ground cable.
50. Connect the air conditioning (AIC)
47. Connect the electronic ignition (El) coil lower-pressure
cut-off switch electrical
electrical connector. connector.
51. Install the right-hand
headlamp assembly.
For additional information, refer to:
Headlamp Assembly (41 7-01 Exterior
Lighting, Removal and Installation).
2006.0 Fiesta 1212006 GI 131 64en
procarmanuals.com