Page 551 of 1226
Engine - 1.25L Duratec-1 6V (Sigma)ll.4L
Duratec-I 6V (Sigma)/l .6L Duratec-16V (Sigma)
REMOVAL
33. Disconnect the NC compressor clutch 36. Disconnect the crankshaft position (CKP)
electrical connector. sensor
electrical connector.
34. Disconnect the NC high-pressure cut-off 37. Disconnect the reversing lamp switch
switch electrical connector. electrical connector.
35. Disconnect the oil pressure switch
electrical connector. 38. Disconnect the ignition switch to starter
motor solenoid and battery to starter motor
solenoid cables.
39m ACAUTION:~~~~ bending of the exhaust
flexible pipe may cause damage resulting
in failure.
2006.0 Fiesta IZIZOO~ G113163en
procarmanuals.com
Page 555 of 1226

Engine - 1.25L Duratec-I 6V (Sigma)llm4L
303-01A-79 Duratec-1 6V (Sigma)/l .6L Duratec-1 6V (Sigma) 303-01 A-79
REMOVAL
56. Disconnect the gearshift actuator electrical Remove the spring clip.
, connector (colored gey).
59. Remove the gearshift cables cover.
57m ACAUTION:I brake fluid is spilt on the
paintwork, the affected area must be
immediately washed down with cold water.
Disconnect the clutch slave cylinder supply
line.
Remove the spring clip.
Vehicles without automated gearshift
58' ACAUTION:~ brake fluid is spilt on the
paintwork, the affected area must be
immediately washed down with cold water.
Disconnect the clutch slave cylinder supply
line.
60. Detach the gearshift cables from the
transaxle.
Detach the gearshift cables and the selector
cable from the selector levers.
Turn the abutment sleeve clockwise and
detach the cables from the bracket.
All vehicles
'Irn ~CAUTION:DO not support the engine
directly on the oil pan.
2006.0 Fiesta 12/2oo6 G113163en
procarmanuals.com
Page 565 of 1226

Engine - 1.25L Duratec-1 6V (Sigma)ll.4L
303-01 A-89 Duratec-1 6V (Sigma)ll.GL Duratec-1 6V (Sigma) 303-01 A-89
REMOVAL
44m ACAUTION:~~~~ bending of the exhaust Vehicles with air conditioning
I flexible pipe may cause damage resulting 47.
Disconnect the air conditioning (NC)
, in failure. low-pressure cutoff switch electrical
Support the exhaust
flexible pipe with a connector.
suitable support
wrap or suitable splint.
48. Disconnect the NC compressor clutch
45. Detach the exhaust flexible pipe from the electrical connector.
catalytic converter.
Discard the nuts and the gasket.
46. Remove the accessory drive belt.
For additional information, refer to:
Accessory Drive
Belt - I .4L Duratec-I 6V
(Sigma)ll .6L Duratec-1 6V (Sigma),
Vehicles With: Air Conditioning (303-05
Accessory Drive, Removal and
Installation)
I Accessory Drive Belt - I .4L Duratec-I 6V
(Sigma)ll .6L Duratec-1 6V (Sigma),
Vehicles Without: Air Conditioning
(303-05 Accessory Drive,
Removal and
Installation).
49. Disconnect the NC high-pressure cutoff
switch
electrical connector.
2006.0 Fiesta 1212006 G380458en
procarmanuals.com
Page 579 of 1226

Engine - 1.25L Duratec-1 6V (Sigma)llm4L
303-01 A-I 03 Duratec-1 6V (Sigma)/l .6L Duratec-1 6V (Sigma) 303-01A-I 03
DISASSEMBLY
43. Remove the oil pan retaining bolts. 46. Remove the oil pump.
Discard the gasket.
Discard the crankshaft front seal.
44m ACAUTION:~~ order to prevent damage
to the sealing surfaces, only use the
designated special tool to remove the oil
Vehicles with manual transaxle
PanmDonotuseachiselorscrewdriverfor 47. Removetheclutchdiscandpressureplate.
removal. For additional information, refer to: Clutch
N0TE:Tighten the lock nut against the oil pan and Disc and Pressure Plate (308-01 Clutch,
use several taps to release the oil pan from the Removal and Installation).
cylinder block. 48. Using the special tool, remove the flywheel.
Using the special tools, remove the oil pan.
Discard the bolts.
45. Remove the oil pump pickup pipe. Vehicles with automatic transaxle
Discard the gasket. 49. Using the special tool, remove the flexplate.
2006.0 Fiesta 1212006 GI 54224en
procarmanuals.com
Page 586 of 1226
Engine - 1.25L Dura
303-01A-11 0 Duratec-16V (Sigma)ll.(
:ec-16V (Sigma)llm4L
L Duratec-16V (Sigma)
303-01 A-I 10
ASSEMBLY
Stage 2: 80 degrees. Stage 2: 80 degrees.
6. Install the clutch disc and pressure plate. 9. Remove the special tool from the flexplate.
For additional information, refer to: Clutch
Disc and Pressure Plate
(308-01 Clutch, All vehicles
Removal and Installation). 10. N0TE:lnstall a new oil pump gasket.
7. Remove the special tool from the flywheel.
Install the oil pump.
Vehicles with automatic transaxle
8. N0TE:lnstall new flexplate retaining bolts.
Using the special tool, install the flexplate.
Tighten the bolts in the sequence shown in
two stages.
Stage1:30Nm.
11. N0TE:lnstall a new pickup pipe gasket.
2006.0 Fiesta 1212006 GI 54225en
procarmanuals.com
Page 602 of 1226
303-01 A-I 26 Engine
- 1.25L Duratec-I 6V (Sigma)ll.4L
Duratec-1 6V (Sigma)ll .6L
Duratec-1 6V (Sigma) 303-01A-I26
INSTALLATION
23. Attach the air conditioning (NC)
compressor to the
cylinder block.
27. Connect the reversing lamp switch
electrical connector.
I
24. Connect the NC compressor clutch
28. Connect the crankshaft position (CKP)
electrical connector. sensor electrical connector.
25. Install the accessory drive belt. 29. Connect the oil pressure switch electrical
For
additional information, refer to: connector.
Accessory Drive
Belt - I .4L Duratec-16V
(Sigma)ll .6L Duratec-1 6V (Sigma),
Vehicles With: Air Conditioning (303-05
Accessory Drive,
Removal and
Installation).
26. Connect the starter motor electrical
connectors.
30.
N0TE:lnstall new exhaust flange nuts and
a new exhaust
flange gasket.
2006.0 Fiesta 1212006 Gll3164en
procarmanuals.com
Page 603 of 1226

Engine - 1.25L Duratec-1 6V (Sigma)ll.4L
303-01 A-I 27 Duratec-1 6V (Sigma)ll .6L Duratec-1 6V (Sigma)
303-01 A-I 27
INSTALLATION
Attach the exhaust flexible pipe to the
33. Attach the gearshift cables to the bracket
catalytic converter.
and turn the abutment sleeves
counterclockwise.
31. Remove the exhaust flexible pipe support.
Vehicles without automated gearshift
32m ACAUTION:H brake fluid is spilt on the
paintwork, the affected area must be
immediately washed down with cold water.
N0TE:Make sure the spring clip is correctly seated.
Connect the clutch slave cylinder supply
line.
Install the spring clip.
34. N0TE:Do not install the air cleaner at this
stage.
Adjust the gearshift cable.
For additional information, refer to: Gearshift Cable Adjustment (308-00 Manual
Transmission/Transaxle and Clutch
General Information, General Procedures).
35.
N0TE:Do not install the air cleaner at this
stage.
Bleed the hydraulic clutch system.
For additional information, refer to: Clutch
System Bleeding (308-00 Manual
Transmission/Transaxle and Clutch -
General Information, General Procedures).
Vehicles with automated gearshift
36. Connect the gearshift actuator electrical
connector (colored grey).
2006.0 Fiesta 1212006
procarmanuals.com
Page 604 of 1226
Engine - 1.25L Dura
303-01 A-I 28 Duratec-16V
(Sigma)/l .r
:eel 6V (Sigma)ll.4L
L
Duratec-1 6V (Sigma) 303-01A-128
INSTALLATION
37. Connect the gearshift actuator electrical All vehicles
connector (colored black). 41. Lower the vehicle.
42. Tighten the engine front mount retaining
nuts and bolts.
38. Install the gearshift actuator cover.
39. Connect the clutch slave cylinder supply
line.
Install the spring clip.
40. Bleed the hydraulic clutch system.
For additional information, refer to: Clutch
System Bleeding
- Vehicles With:
Automated Gearshift
(308-00 Manual
~ransmission/Transaxle and Clutch -
General Information, General Procedures).
43. N0TE:lnstall a new engine rear mount
center retaining nut.
Tighten the engine rear mount center
retaining nut.
44. Attach the power steering line support
bracket to the cylinder head.
2006.0 Fiesta 1212006 GII 31 64en
procarmanuals.com