2007 FORD FIESTA clutch

308-03-64 Manual Transmission/Transaxle 308-03-64
INSTALLATION
13. Connect the vehicle speed sensor (VSS) 16. Raise and support the vehicle. For
electrical connector (if equipped). additional information, refer to
Section 100-02 [Jacking and Lifting].
17. CAUTIONS:
Asupport the halfshaft. The inner joint
must not be bent more than 18 degrees.
The outer joint must not be bent more than
45 degrees.
ADO not damage the halfshaft oil seal.
Attach the right-hand halfshaft and the
intermediate shaft to the transaxle.
14' ACAUTION:~~ brake fluid is spilt on the
paintwork, the affected area must be
immediately washed down with cold water.
N0TE:Make sure the spring clip is correctly seated.
Connect the clutch slave cylinder supply
line.
Install the spring clip.
15. Attach the coolant expansion tank to the
bracket. 18.
N0TE:lnstall a
new center bearing cap and
locknuts.
Install the intermediate shaft center bearing
cap.
I. Install the center bearing cap.
2. Attach the heat shield.
3. Install the locknuts.
19. CAUTIONS:
Asupport the halfshaft. The inner joint
must not be bent more than 18 degrees.
The outer joint must not be bent more than
45 degrees.
2006.0 Fiesta 1212006 GI I 3293en
procarmanuals.com

308-03-66 Manual Transmission/'rransaxle 308-03-66
INSTALLATION
24. Attach the gearshift cables to the selector 27. Install the gearshift actuator cover.
levers.
Vehicles with automated gearshift
25. Connect the gearshift actuator electrical
connector (colored grey).
26. Connect the gearshift actuator electrical
connector (colored black).
28. Connect the clutch slave cylinder supply
line.
Install the clip.
All vehicles
29. Connect the reversing lamp switch
electrical connector.
30. Install the starter motor.
2006.0 Fiesta 1212006 GII 3293en
procarmanuals.com

308103168 Manual Transmission/Transaxle 308103168
INSTALLATION
37. Connect the powertrain control module
(PCM) electrical connector to the PCM.
38. Install the front wheels and tires. For
additional information, refer to
Section
204-04 wheels and Tires].
Vehicles without automated gearshift
39. Adjust the gearshift cables. For additional
information, refer to Section
308-00
[Manual Transmission/Transaxle and Clutch
- General Information].
40. Bleed the clutch system. For additional
information, refer to Section
308m00
[Manual Transmission/Transaxle and Clutch
- General Information].
All vehicles
41. Install the battery tray. For additional
information, refer to Section
41 4-01
[Battery, Mounting and Cables].
42. With the vehicle on a level surface, fill the
transaxle until the oil level is just below the
bottom of the filler hole.
Vehicles with automated gearshift
43m ACAUTION:T~~ worldwide diagnostic
system (WDS) gearshift actuator bleed
option must be carried out
if any part of the
clutch hydraulic system is opened or any
new components are installed.
N0TE:When the WDS gearshift actuator bleed
option is selected, the learn transmission and learn
clutch parameter options will automatically be
completed.
Bleed the clutch system. For additional
information, refer to Section
308-00 [Manual
Transmission/Transaxle and Clutch - General
Information].
2006.0 Fiesta 1212006 GII 3293en
procarmanuals.com

308-03-71 Manual Transmission/Transaxle 308-03-71
INSTALLATION
Attach the exhaust flexible pipe to the 15.
Remove the support wrap or suitable splint
catalytic converter. from
the exhaust flexible pipe.
i
3m ACAUTION:~~ brake fluid is spilt on the 16. lnstall the right-hand halfshaft.
paintwork, the affected area must be For additional information,
refer to: Front
immediately washed down with cold water. Halfshaft
RH (205-04 Front Drive
N0TE:Make sure the spring clip is correctly seated. Halfshafts, Removal and Installation).
Connect the clutch slave cylinder supply
17. lnstall the left-hand halfshaft.
line. For additional information,
refer to: Front
lnstall the spring clip. Halfshaft LH (205-04 Front Drive
Halfshafts, Removal and Installation).
18. lnstall the engine support insulator.
14. Raise and support the vehicle. For
additional information, refer to: (I
00-02
Jacking and Lifting)
19. Install the accessory drive belt cover.
Jacking (Description and Operation),
Lifting (Description and Operation).
2006.0 Fiesta 1212006 G453417en
procarmanuals.com

308-03-74 Manual Transmission/Transaxle 308-03-74
INSTALLATION
34. Adjust the gearshift cables.
For additional information, refer to:
Gearshift Cable Adjustment
(308-00
Manual Transmission/Transaxle and
Clutch
- General Information, General
Procedures).
35. Bleed the clutch system.
For additional information, refer to: Clutch
System Bleeding (308-00 Manual
Transmission/Transaxle and Clutch -
General Information, General Procedures).
36, Install the battery tray.
For additional information, refer to: Battery
Tray
- 2.OL Duratec-HE (M14) (414-01
Battery, Mounting and Cables, Removal
and
Installation).
37. With the vehicle on a level surface, fill the
transaxle until the fluid level is just below
the bottom of the filler hole.
2006.0 Fiesta 1212006 G453417en
procarmanuals.com

Manual Transmission/Transaxle External
308-06-5 Controls
308-06-5
External Controls
Inspection and Verification 4. If an obvious cause for an observed or reported
concern is found, correct the cause (if possible)
1. Verify the customer concern. before proceeding to the next
step.
2. Visually inspect for obvious signs of mechanical 5.
If the concern is not visually evident, verify the
damage. symptom
and refer to the Symptom Chart.
3. Make sure that the gearshift cables are correctly
routed and not under any tension from other
components.
Symptom Chart
Symptom
External controls do not
operate freely. Possible Sources
Action
Gearshift cables incorrectly
adjusted.
Gearshift lever damaged.
Selector mechanism damaged.
Gearshift cables damaged. ADJUST
the gearshift cables.
REFER to: Gearshift Cable
Adjustment
- Vehicles With:
5-Speed Manual Transaxle
(iB5) (308-00 Manual Trans-
mission/Transaxle and Clutch
- General Information,
General Procedures).
GO to Pinpoint Test A.
Pinpoint Tests
PINPOINT TEST A : STIFF GEARSHIFT
TEST CONDITIONS
DETAILSIRESU LTSIACTIONS
Al: CHECK THE GEARSHIFT LEVER
Detach the gearshift cables from the gearshift
lever.
Is the gearshift lever difficult to operate?
+ Yes
Install a new gearshift lever.
REFER to: Gearshift Lever (308-06 Manual
TransmissionlTransaxle External Controls,
Removal and Installation).
-, No
GO to
A2.
A2: CHECK THE GEARSHIFT CABLES
Attach the gearshift cables to the gearshift lever.
2006.0 Fiesta IZIZOO~ G37664en
procarmanuals.com

Manual Transmission/Transaxle External
Controls
REMOVAL AND INSTALLATION
Gearshift Lever(l6 524 0)
Removal
I. Remove the gearshift lever trim panel.
Disconnect the cigar lighter electrical
connector.
2. Detach the gearshift cables from the
gearshift lever.
4. Remove the gearshift lever front retaining
bolts.
5. Remove the gearshift lever.
Remove the bolts.
Installation
1. To install, reverse the removal procedure. 3. Detach the gearshift cables from the
retaining bracket. 2. Adjust the gearshift cables. For additional
information, refer to Section
308-00 [Manual Turn the abutment sleeves clockwise. Transmission/Transaxle and Clutch - General
Information].
2006.0 Fiesta 1212006 GI 86744en
procarmanuals.com

Manual Transmission/Transaxle External
308-06-1 1 Controls 308-06-1 1
REMOVAL AND INSTALLATION
12. Adjust the gearshift cables. For additional
information, refer to Section
308-00
i ' [Manual Transmission/Transaxle and Clutch
- General Information].
-- -
2006.0 Fiesta 1212006 GI 86745en
procarmanuals.com