2007 FORD FIESTA wheel

303-01 B-59 Engine - 2.OL Duratec-HE (M14) 303-01 B-59
IN-VEHICLE REPAIR
Install the flywheel. 12. Install the oil level indicator tube lower
retaining bolt.
9. Using the special tool, lock the flywheel in
position. 13.
Install the clutch disc and pressure plate.
10. Tighten the flywheel retaining bolts. For
additional information, refer to: Clutch
Disc and Pressure Plate (308-01 Clutch,
Removal and installation).
14. Install the oil level indicator and oil level
indicator tube upper retaining bolt.
Tighten the bolts in the sequence shown in
three stages.
Stage I: 50 Nm.
Stage2: 80 Nm.
Stage 3: 112 Nm. 15. Fill the engine with engine oil.
11. Remove the special tool. For
additional information, refer to:
Specifications
(303-01 Engine - 2.OL
Duratec-HE (M14), Specifications).
2006.0 Fiesta 1212006 G451307en
procarmanuals.com

303-01 B-79 Engine - 2.OL Duratec-HE (M14) 303-01 B-79
REMOVAL
34. Detach the powertrain control module 37. CAUTIONS:
(PCM) support bracket from the side
i member. A~he inner CV joint must not be bent
more than
23 degrees. The outer CV joint
35m ACAUTION:P~~~~~~ the ball joint seal
using
a soft cloth to prevent damage.
Detach the lower arm ball joint from the
wheel knuckle on both sides.
Remove the heat shield.
must not be bent more than 45 degrees.
A~ake sure the halfshaft seal is not
damaged.
Aplug the transaxle to prevent oil loss or
dirt ingress.
Remove the halfshaft and intermediate shaft
assembly.
Allow the oil to drain into a suitable container.
38. CAUTIONS:
Asupport the halfshaft. The inner joint
must not be bent more than
I8 degrees.
The outer joint must not be bent more than
45 degrees.
ADO not damage the halfshaft seal.
N0TE:Plug the transaxle to prevent oil loss or dirt
ingress.
36. Remove the intermediate shaft center
bearing cap. Remove
the left-hand halfshaft.
Discard the bearing cap and retaining nuts.
Remove the intermediate shaft center
bearing heat shield (if equipped).
2006.0 Fiesta 1212006 G451290en
procarmanuals.com

303-01 B-83 Engine - 2.OL Duratec-HE (M14) 303-01 B-83
DISASSEMBLY
Engine(21 134 8)
/ 1
Special Tool(s)
Universal Flange Holding
Wrench
205-072 (1 5-030A)
Adapter for 205-072
205-072-02 (1 5-03OA-02)
Locking Tool, Flywheel
303-254 (2 1 -1 35)
Mounting Plate for
303-435-06
303-435-1
1A (21 -146D)
Socket, Spark Plug
303-499 (2 1 -202)
Pliers, Valve Stem Seal
303-508 (2 1-2 1 1 )
I I Removerllnstaller, Hose I Disassembly
1. Disconnect the generator electrical
connector.
Mounting Stand
303-435 (21 -1 87)
2006.0 Fiesta 1212006 G451309en
procarmanuals.com

303-01 B-93 Engine - 2.OL Duratec-HE (M14) 303-01 B-93
DISASSEMBLY
Discard the gasket. 59. Using
the special tool, lock the flywheel in
position.
56. Remove the crankcase vent oil separator.
60. Remove the flywheel.
Discard the bolts.
57.
Remove the oil filter adapter.
Discard the gasket.
61.
Remove the special tool.
62. Remove the oil pan.
58. Remove the clutch disc and pressure plate.
For additional information, refer to: Clutch
Disc and Pressure 'late (308-01 Clutch, 63. Remove the crankshaft rear seal carrier.
Removal and Installation).
2006.0 Fiesta 1212006 G451309en
procarmanuals.com

303-01 B-96 Engine - 2.OL Duratec-HE (M14) 303-01 B-96
ASSEMBLY
Tighten the bolts in the sequence shown. 7. N0TE:lnstall new flywheel bolts.
Install the flywheel.
Clean the mating faces of the cylinder block
I
and the oil pan with a suitable metal surface
cleaner.
8. Using the special tool, lock the flywheel in
position.
N0TE:lnstall the oil pan within 10 minutes
of applying the sealant and tighten the
retaining bolts within a further
5 minutes.
Apply a
3 mm bead of sealant to the oil pan.
9. Tighten the flywheel bolts.
Tighten the bolts in the sequence shown in
three stages.
5. Using a suitable straight edge, align the oil Stage 1: 50 Nm.
pan to the cylinder block mating face on the Stage 2: 80 Nm.
timing chain side. Stage 3: 11 2 Nm. I I
6. Tighten the oil pan retaining bolts.
Tighten the bolts in the sequence shown.
l I. -.
10. Remove the special tool.
2006.0 Fiesta 1212006 G451310en
procarmanuals.com

303-01 B-I 14 Engine - 2.OL Duratec-HE (M14) 303-01 B-114
INSTALLATION
20. CAUTIONS: 22m ACAUTION:M~~~ sure that the lower arm
ball joint heat shield is installed to prevent
A~he inner CV joint must not be bent damage
to the ball joint.
Remove the special tool before fully installing Tighten the center bearing cap retaining nuts.
more than 23 degrees. The outer CV joint
Install the lower arm ball joint heat shield.
must not be bent more than
45 degrees. I
the halfshaft.
A~ake sure the halfshaft seal is not
damaged.
I -
Using the special tool, attach the right-hand
halfshaft and intermediate shaft assembly
to the transaxle.
Remove the special tool before fully installing
the halfshaft.
21.
N0TE:lnstall a new intermediate shaft
center bearing cap and retaining nuts.
N0TE:Make sure that the intermediate shaft center
bearing is correctly positioned in the intermediate
shaft center bearing retaining bracket.
Install the intermediate shaft center bearing
cap.
Position the center bearing cap.
Position the intermediate shaft center bearing
heat shield (if equipped).
23m ACAUTION:T~~ lower arm pinch bolt must
be installed from the rear of the wheel
knuckle.
Attach the lower arm ball joint to the wheel
knuckle.
-- -
2006.0 Fiesta 1212006 ~451291 en
procarmanuals.com

303-06-3 Starting System 303-06-3
DESCRIPTION AND OPERATION
Starting System
Starting system
1 tern Description
I 1 I lgnitionlstarter switch I
1 2 1 Starter relay I
1 3 1 Electric starter motor I
1 4 1 Powertrain control module (PCM) I
1 5 1 Sensor,- crankshaft position ( CKP) I
The purpose of the starting system is to turn the
engine crankshaft at a speed which enables the
engine to start.
The engine is started as follows:
Ignitionlstarter switch in position
Ill.
The starter relay is activated by the PCM .
The solenoid is supplied with voltage.
The solenoid engages the starter motor pinion
with the flywheel ring gear.
The solenoid applies battery current to the
starter.
The starter turns the crankshaft until the engine
starts. The key can then be released and it
automatically returns to position
I I.
The system incorporates the "Smart
StartingWstrategy. This makes starting faster and
protects the starter.
If the driver fails to release the key immediately
after the engine starts, the PCM interrupts
activation of the starter relay and thus switches off
the electric starter motor.
The speed signal provided by the CKP sensor is
used for monitoring the starting procedure.
2006.0 Fiesta 1212006 GI 63308en
procarmanuals.com

303-06-5 Starting System 303-06-5
DIAGNOSIS AND TESTING
Symptom
The engine cranks slowly
Unusual starter noise
The starter spins but the engine
does not crank
Possible Sources Action
Relay.
Battery.
Starter motor.
Starter motor.
Flywheel ring gear.
Starter motor.
Flywheel ring gear.
CARRY OUT the relay
Component Test. REFER to
the wiring diagrams.
GO to Pinpoint Test B.
REFER to: Charging System
(414-00 Charging System
-
General Information,
Diagnosis and Testing).
CARRY OUT the starter motor
Component Test using WDS.
GO to Pinpoint Test C.
REMOVE the starter motor.
REFER to: (303-06 Starting
System)
Starter Motor
- 1.3L Duratec-8V
(Rocam)/l.25L Duratec-I 6V
(Sigma)/l.4L Duratec-1 6V
(Sigma)/l .6L Duratec-1 6V
(Sigma) (Removal and
Installation),
Starter Motor - 1.4L Duratorq-
TDCi (DV)
Diesel (Removal
and Installation).
INSPECT the starter motor
gear for damage. INSTALL a
new starter motor as neces-
sary.
INSPECT the flywheel for
damage.
REMOVE the starter
motor.REFER to: (303-06
Starting System)
Starter Motor
- 1.3L Duratec-8V
(Rocam)/l.25L Duratec-1 6V
(Sigma)/l.4L Duratec-I 6V
(Sigma)ll .6L Duratec-I 6V
(Sigma) (Removal and
Installation),
Starter Motor - 1.4L Duratorq-
TDCi (DV)
Diesel (Removal
and Installation).
INSPECT the starter motor
gear for damage. INSTALL a
new starter motor as neces-
sary.
INSPECT the flywheel for
damage.
2006.0 Fiesta 1212006 Gl51301en
procarmanuals.com