2007 FORD FIESTA section 4

21 1-03-8 Steering Linkage 21 1-03-8
REMOVAL AND INSTALLATION
Tie Rod(l3 263 0)
General Eaui~ment
Special Tool(s) 3. Remove and discard the steering gear boot
I Pipe wrench I
13025
I Vise jaw protectors I
Pincers Socket, Tie-Rod End,
Steering
Gear
2 1 1 -245
(1 3-025)
clamps.
1 Grease I ESB-MIC119-B I
Materials
Removal
4. Remove and discard the steering gear boot.
1. Remove the steering gear. For additional
information, refer to Section
211-02 [Power
Steering].
2.
N0TE:Make a note of the number of turns
used to remove the tie-rod end.
Name
S~ecification
Remove
the tie-rod end and the tie-rod end
locknut.
1. Remove the tie-rod end.
2. Remove the tie-rod end locknut.
5. Rotate the steering gear pinion to expose
the rack.
6. CAUTIONS:
ADO not clamp the steering rack on ( ' ' exposed hydraulic sealing surfaces.
A~ake sure vise jaw protectors are used.
2006.0 Fiesta 1~2006 G91976en
procarmanuals.com

21 1 -03-1 0 Steering Linkage 21 1-03-1 0
REMOVAL AND INSTALLATION
6. Install the steering gear. For additional
information, refer to Section
211-02 [Power
Steering].
2006.0 Fiesta 1212006 G91976en
procarmanuals.com

21 1-04-1 Steering Column 21 I -04-1
SECTION 211 -04 Steering Column
VEHICLE APPLICATION:2006.0 Fiesta
CONTENTS PAGE
SPECIFICATIONS
Specifications.. ........................................................................\
............................................ 2 1 1 -04-2
DIAGNOSIS AND TESTING
Steering Column ........................................................................\
.........................................
REMOVAL AND INSTALLATION
Steering Wheel ........................................................................\
....................... (1 3 524 0)
Steering Column ........................................................................\
................. (1 3 542 0)
DISASSEMBLY AND ASSEMBLY
Steering Column ........................................................................\
..................... (1 3 543 4)
procarmanuals.com

21 I -04-3 Steering Column 21 1 -04-3
DIAGNOSIS AND TESTING
Steering Column
REFER to Section 211-00 [Steering System -
General Information].
2006.0 Fiesta 1212006 G91977en
procarmanuals.com

21 1-05-1 Steering Column Switches 21 1-05-1
SECTION 211 -05 Steering Column Switches
VEHICLE APPLICATION:2006.0 Fiesta
CONTENTS PAGE
REMOVAL AND INSTALLATION
Ignition Switch ........................................................................\
........................ (36 424 0) 2 1 1 -05-2
procarmanuals.com

21 1-05-2 Steering Column Switches 21 1-05-2
REMOVAL AND INSTALLATION
Ignition Switch(36 424 0)
Removal 2. Detach the shroud.
I. Disconnect the battery ground cable. For
additional information, refer to
Section
414-01 [Battery, Mounting and
Cables].
2. Detach the audio control switch from the
steering column lower shroud (if equipped).
Using a thin bladed screwdriver, release the
locking tang.
3. Remove the audio control switch (if
equipped).
Disconnect the electrical connector.
.. N0TE:Turn the steering wheel to access the
steering column upper shroud retaining
clips.
Detach the steering column upper shroud
from the steering column lower shroud (steering wheel shown removed for clarity).
5. Remove the steering column lower shroud
(steering wheel shown removed for clarity).
1. Release the steering column locking lever.
2. Remove the retaining screws.
6. Disconnect the ignition switch electrical
connector.
1. Using a thin bladed screwdriver, release the 7m Remove the ignition two clips (one each side).
2006.0 Fiesta 1212006 GI 05656en
procarmanuals.com

303-00-1 Engine System = General Information 303-00-1
SECTION 303-00 Engine System . General lnformation
VEHICLE APPLICATION:2006.0 Fiesta
CONTENTS PAGE
DESCRIPTION AND
OPERATION
Engine
........................................................................\
......................................................... 303-00-3
Engineltransmission combinations ........................................................................\
........ 303-00-3
DIAGNOSIS AND TESTING
........................................................................\
.......................................................... Engine
. Engine Oil Leaks ........................................................................\
........................................
Ultraviolet (UV) Testing ........................................................................\
...............................
Measure the compression pressure ........................................................................\
...........
.............. Measure the compression pressure (Engine . 1.4L Duratorq-TDCi (DV) Diesel)
Measure the compression pressure (Engine
. 1.6L Duratorq-TDCi (DV) Diesel) ..............
Measure the compression pressure (Engine . 1.25L Duratec-I 6V (Sigma)/l.4L Duratec-I 6V
........................................................................\
......... (Sigma)ll . 6L Duratec-I 6V (Sigma))
Measure the compression pressure (Engine
. 1.3L Duratec-8V (Rocam)) ........................
Measure the compression pressure (Engine . 2.OL Duratec-HE (M14)) .............................
. Measure the oil pressure (Engine 1.4L Duratorq-TDCi (DV) Diesel) ...............................
Measure the oil pressure (Engine . 1.6L Duratorq-TDCi (DV) Diesel) ...............................
Measure the oil pressure (Engine . 1.25L Duratec-1 6V (Sigma)/l.4L Duratec-1 6V
........................................................................\
......... (Sigma)/l . 6L Duratec-1 6V (Sigma))
. Measure the oil pressure (Engine 1.3L Duratec-8V (Rocam)) .........................................
. Measure the oil pressure (Engine 2.OL Duratec-HE (M14)) ...............................................
Valve train analysis . static (engine off) ........................................................................\
......
GENERAL PROCEDURES
Camshaft Bearing Journal Diameter
........................................................................\
..........
Camshaft Bearing Journal Clearance ........................................................................\
.........
Camshaft End Play ........................................................................\
.....................................
Camshaft Surface Inspection ........................................................................\
.....................
........................................................................\
...................................... Camshaft Lobe Lift
Crankshaft Main Bearing Journal Diameter
........................................................................\

Crankshaft End Play ........................................................................\
...................................
Cylinder Bore Taper ........................................................................\
....................................
Piston Inspection ........................................................................\
........................................
Piston Pin to Bore Diameter ........................................................................\
.......................
Piston Diameter ........................................................................\
..........................................
Piston Ring End .Gap ........................................................................\
...................................
............................................ ................................... Piston Ring-to-Groove Clearance ......
Piston Pin Diameter ........................................................................\
.....................................
Connecting Rod Large End Bore ........................................................................\
................
Valve Stem Diameter ........................................................................\
..................................
Flywheel Inspection ........................................................................\
....................................
............................................... Flywheel Inspection - Vehicles With: Dual Mass Flywheel
Cylinder Head Distortion ........................................................................\
.............................
Cylinder Block Distortion ........................................................................\
.............................
procarmanuals.com

303-00-33 Engine System - General Information 303-00-33
GENERAL PROCEDURES
Camshaft Bearing Journal Clearance
1. N0TE:Make sure that the following stages The value that is read off is the bearing
are followed exactly. The tappets or followers clearance.
must be removed to carry out this
measurement.
N0TE:Make sure that the camshaft is to
specification.
N0TE:The bearing caps and journals should be
free from engine oil and dirt.
Position on a width of plastigage on the
bearing cap.
Insert the camshaft, without lubrication, into
the cylinder head.
Position
a plastigage strip, which should be
equal to the width of the bearing cap, on the
bearing journal.
2. Following the tightening specification, install
the camshaft bearing caps. Refer to the
corresponding Section 303-01.
3.
N0TE:Do not strike the bearing caps.
Remove the camshaft bearing caps, refer to
the corresponding Section 303-01.
'4. Using the Plastigage, read off the
measurement.
Compare the width of plastigage with the
plastigage scale.
2006.0 Fiesta 1212006
procarmanuals.com