2007 FORD FIESTA section 4

21 I -02-4 Power Steering 21 1-02-4
DIAGNOSIS AND TESTING
Power Steering
REFER to Section 211-00 [Steering System -
General Information].
2006.0 Fiesta 1212006 GI 7571 en
procarmanuals.com

21 1 -02-49 Power Steering 21 I -02-49
REMOVAL AND INSTALLATION
Steering Gear Bushing
/ I
Special Tool(s) 3. Using the special tools remove the steering
( 'Removal
1. Remove the steering gear.
For additional information, refer to Steering
Gear in this section.
2. CAUTIONS:
A~ake sure vise jaw protectors are used.
hamp the steering gear reinforcement
boss. Do not clamp the steering gear body.
Secure the steering gear in a vise.
Materials
3. Install the
steering gear.
gear
insulator bushing on both sides.
Installation
14037
1. Lubricate the steering bushing with Rubber
For additional information, refer to Steering
Gear in this section.
Installer, Wheel Hub
204-1 48 (1 4-037)
Removerllnstaller, Pivot
Bushing
205-297 (1 5-086)
2006.0 Fiesta 1212006 G91973en
Name Specification Suspension Insulator Lubricant prior to
installation.
2. Using the special tools install the steering
Rubber Suspension
Insulator Lubricant
gear insulator bushing on both sides.
E25J-I 9553-A
procarmanuals.com

21 1-03-1 Steering Linkage 21 1=03-I
SECTION 211 -03 Steering Linkage
VEHICLE APPLICATION:2006.0 Fiesta
CONTENTS
SPECIFICATIONS
........................................................................\
............................................ Specifications..
DIAGNOSIS AND TESTING
........................................................................\
....................................... Steering Linkage..
REMOVAL AND INSTALLATION
Tie Rod End
........................................................................\
.......................... (1 3 273 0)
Steering Gear Boot ........................................................................\
................. (1 3 134 0)
........................................................................\
................................... Tie Rod (1 3 263 0)
PAGE
procarmanuals.com

211 -03-3 Steering Linkage 21 1-03-3
DIAGNOSIS AND TESTING
Steering Linkage
REFER to Section 21 1-00 [Steering System -
General Information].
2006.0 Fiesta 1212006 GI 7594en
procarmanuals.com

211 -03-4 Steering Linkage 21 1-03-4
REMOVAL AND INSTALLATION
Tie Rod End(l3 273 0)
Special Tool(s)
I Separator, Ball Joint
2. Remove and discard the tie-rod end retaining (,,
nut.
Removal
1. Remove the wheel and tire.For additional
information, refer to Section 204-00
[Suspension System
- General Information].
4. N0TE:Make a note of the number of turns
2m &AUTION:L~~~~ the tie-rod end retaining used to remove the tie-rod endrn
nut in place to protect the ball joint stud.
Remove the tie-rod end.
N0TE:Use a 5 mm Allen key to prevent the ball
joint stud from rotating.
Loosen the tie-rod end locknut and the
tie-rod end retaining nut.
1. Loosen the locknut.
2. Loosen the retaining nut.
3m &Au~l~N:~rotect the ball joint seal using
a soft cloth to prevent damage.
Using the special tool, detach the tie-rod end
from the wheel knuckle.
1. Release the tie-rod end.
Installation
I. N0TE:lnstall the tie-rod end using the same
number of turns used to remove
it.
Install the tie-rod end.
2006.0 fiesta 12,2006 GI 05650en
procarmanuals.com

21 1 -03-5 Steering Linkage 21 1 -03-5
REMOVAL AND INSTALLATION
2m AwARNING:~~~~~~~ a new tie-rod end
/ I retaining nut. Failure to follow this
instruction may result in personal injury.
N0TE:Use a 5 mm Allen key to prevent the ball
joint stud from rotating.
Attach the tie-rod end to the wheel knuckle.
1. Tighten the retaining nut.
2. Tighten the locknut.
3. Install the wheel and tire.For additional
information, refer to Section 204-00
f ' [Suspension System - General Information]. ' ' 4. Check the toe setting and adjust as
necessary. For additional information, refer
to Section 204-00 [Suspension System
-
General Information].
- - --
2006.0 Fiesta 1212006 GI 05650en
procarmanuals.com

21 1 -03-6 Steering Linkage 21 1-03-6
REMOVAL AND INSTALLATION
Steering Gear Boot(l3 134 0)
General Equipment Install
the steering gear boot. (:
1 Pincers I
Materials
Name
S~ecification
1 Grease I ESB-MI C119-B I
Removal
1. Remove the tie-rod end.
For additional information, refer to Tie-Rod
End in this section.
2. Remove the tie-rod end locknut.
3. N0TE:Make sure the tie-rod is clean before
removing the steering gear boot.
Remove the steering gear boot.
2. Using a suitable pair of pincers, install a new
steering gear boot inner clamp.
3. N0TE:Make sure the steering gear boot outer
clamp is located over the recess in the
Discard the clamps. tie-rod.
Installation
I. N0TE:Lubricate the steering gear boot. Using
a suitable pair of pincers, install a new
steering gear boot outer clamp.
2006.0 Fiesta 1212006 GI 05651 en
procarmanuals.com

211 -03-7 Steering Linkage 21 1-03-7
REMOVAL AND INSTALLATION
4, Install the tie-rod end locknut.
5. Install the tie-rod end.
For additional information, refer to Tie-Rod
End in this section.
2006.0 Fiesta 1212006 GI 05651 en
procarmanuals.com