2007 FIAT IDEA run flat

175
CORRECT USE
OF THE CAR
WARNING
LIGHTS AND
MESSAGES
IN AN
EMERGENCY
CAR
MAINTENANCE
TECHNICAL
SPECIFICATIONS
INDEX
DASHBOARD
AND CONTROLS
SAFETY
DEVICES
GENERAL WARNINGS
WARNING
If warning light ¬does not come on when turning the key to MAR or if it stays on
when travelling it could indicate a failure in restraint systems; in this case air bags
or pretensioners could not trigger in the event of an accident, or in a restricted
numbers of cases they could trigger accidentally. Stop the car and contact Fiat
Dealership to have the system checked immediately.WARNING
WARNINGAlways keep your hands on the steering wheel rim when driving, so that if the air
bag is triggered, it can inflate without meeting any obstacles which could cause
serious harm to you. Do not drive with the body bent forwards, keep the seat back
rest in the erect position and lean your back well against it. Do not cover the back rest of front seats with trims or covers there are not set for
the use of side bags.
If the car has been stolen or an attempt to steal it has been made, if it has been
subjected to vandals or floods, have the air bag system checked by Fiat Dealership.WARNING
WARNINGRemember that with the key engaged and in the MAR position, even with the
engine not running, the air bags may be triggered on a stationary vehicle if it is
bumped by another moving car. Therefore, never seat children on the front seat
even when the vehicle is stationary. On the other hand remember that if the key is
at STOP, no safety system (air bags or pretensioners) is triggered in the event of an
impact; in these case, failure to come into action cannot be considered as a sign
that the system is not working properly.

USING THE GEARBOX
To engage the gears, press the clutch pedal fully and shift the gear lever
into one of the required positions (the diagram is shown on the knob).
IMPORTANT The car can only be put into reverse gear when it has
stopped moving completely. With the engine running, before engaging the
reverse, wait at least 2 seconds with the clutch pedal fully down to
prevent damage and grating of the gears.
To engage 6
thgear (where fitted), press the lever to the right to prevent
engaging 4thgear by mistake. A similar action is required to shift down
from 6thto 5th
To engage reverse (R) from neutral, lift the sliding ring (A) under the
knob and shift the lever to the right and back (only for petrol versions).
For Multijet versions, just shift lever to the right and back.
182
SAFETY
DEVICES
WARNING
LIGHTS AND
MESSAGES
IN AN
EMERGENCY
CAR
MAINTENANCE
TECHNICAL
SPECIFICATIONS
INDEX
DASHBOARD
AND CONTROLS
CORRECT USE
OF THE CAR
F0H0150m
F0H0353m
To change gears properly you must push the clutch pedal fully down. It is therefore
essential that there is nothing under the pedals: make sure mats are lying flat and do
not get in the way of the pedals.WARNING
Do not drive with your hand resting on the gear lever as the force exerted, even if slight, could lead
over time to premature wear on the gearbox internal components.

226
SAFETY
DEVICES
CORRECT USE
OF THE CAR
WARNING
LIGHTS AND
MESSAGES
CAR
MAINTENANCE
TECHNICAL
SPECIFICATIONS
INDEX
DASHBOARD
AND CONTROLS
IN AN
EMERGENCY
IMPORTANT Do not use the quick repairing kit if the
tyre is damaged due to driving with the wheel
flattened.IT SHOULD BE NOTICED THAT:
The sealing fluid of the quick tyre repair kit is effective
with external temperatures between –20 °C and +50
°C.
The sealing fluid has limited life.
WARNINGHoles and damages on the tyre side walls cannot be repaired. Do not use the quick
tyre repair kit if damaging is due to running with flat tyre. In the event of a puncture caused by foreign bodies, it is possible to repair tyres showing damages
on the track or shoulder up to max 4 mm diameter.
Repairs are not possible in case of damages on the wheel rim (bad groove
distortion causing air loss). Do not remove foreign bodies (screws or nails) from the
tyre.WARNING
The compressor shall not be operated for more than 20 minutes. Risk of
overheating!. Tyres repaired with the quick tyre repair kit shall be used temporarily
only.WARNING

INFLATING PROCEDURE
❒Pull up the handbrake. Loosen tyre inflation valve cap, take out the
filler hose Aand screw the ring nut Bon the tyre valve;
227
SAFETY
DEVICES
CORRECT USE
OF THE CAR
WARNING
LIGHTS AND
MESSAGES
CAR
MAINTENANCE
TECHNICAL
SPECIFICATIONS
INDEX
DASHBOARD
AND CONTROLS
IN AN
EMERGENCY
F0H0356m
Replace the cylinder if sealer has run out. Do not throw away the cylinder and the sealing fluid.
Have the sealing fluid and the cylinder disposed of in compliance with national and local
regulations.
Put on the protection gloves provided together with quick tyre repair kit.WARNING
WARNINGThe cylinder contains ethylene glycol. The cylinder contains latex: it can cause
allergic reactions. It is harmful if ingested or inhaled and irritant for the eyes and in
case of contact. In case of contact rinse immediately with water and take off
contaminated clothes. If swallowed, do not induce vomit, rinse out the mouth,
drink a lot of water and call the doctor immediately. Keep away from children.
This product must not be used by asthmatics. Do not inhale vapours. Call the
doctor immediately in case of allergic reactions. Keep the cylinder in the space
provided for the purpose and far from heat. The sealing fluid has limited life.

229
SAFETY
DEVICES
CORRECT USE
OF THE CAR
WARNING
LIGHTS AND
MESSAGES
CAR
MAINTENANCE
TECHNICAL
SPECIFICATIONS
INDEX
DASHBOARD
AND CONTROLS
IN AN
EMERGENCY
It is of vital importance to communicate that the tyre has been repaired using the
quick tyre repair kit. Hand the instruction brochure to the personnel charged with
treating the tyre repaired with the kit.WARNING
❒if reaching the tyre pressure specified in paragraph “Inflation pressure”
in section “Technical Specifications”, start driving immediately;
❒after driving for about 10 minutes stop and check again the tyre pres-
sure; pull up the handbrake;
❒if at least 1.8 bar pressure is read, restore proper pressure (with engine
running and handbrake on) and restart;
❒drive with the utmost care to the nearest Fiat Dealership.
FOR CHECKING AND RESTORING PRESSURE ONLY
The compressor can be also used just for restoring pressure. Disconnect
the quick connection and connect it directly to the tyre valve; in this way the
cylinder is not connected to compressor and the sealing fluid will not flow
into the tyre.
CYLINDER REPLACEMENT PROCEDURE
To replace the cylinder proceed as follows:
❒disconnect connection A;
❒turn counter-clockwise the cylinder to replace and raise it;
❒fit the new cylinder and turn it clockwise;
❒connect connection Ato the cylinder and fit the transparent tube Bin-
to the proper space.
F0H0359m
F0H0360m