2007 CHEVROLET MONTE CARLO Owners Manual

✍NOTES
145

Instrument Panel Overview
146

The main components of your instrument panel are listed here:
A. Air Vent. SeeOutlet Adjustment on page 168.
B. Remote Trunk Release Button. See “Remote
Trunk Release” underTrunk on page 101.
C. Multifunction Lever. SeeTurn
Signal/Multifunction Lever on page 149.
D. Instrument Panel Cluster. SeeInstrument Panel
Cluster on page 171.
E. Hazard Warning Flasher Button. SeeHazard
Warning Flashers on page 148.
F. Driver Information Center (DIC) Buttons. See
Driver Information Center (DIC) on page 186.
G. Audio System. SeeAudio System(s) on
page 210.
H. Exterior Lamps Control. SeeExterior Lamps
on page 156.
I. Instrument Panel Brightness. SeeInstrument
Panel Brightness on page 159.
J. Traction Control On/Off Button (If Equipped).
SeeTraction Control System (TCS) on
page 254.K. Tilt Steering Wheel Lever. SeeTilt Wheel on
page 148.
L. Cruise Control Buttons. SeeCruise Control
on page 153.
M. Hood Release. SeeHood Release on
page 307.
N. Horn. SeeHorn on page 148.
O. Audio Steering Wheel Controls (If Equipped).
SeeAudio Steering Wheel Controls on
page 240.
P. Ignition Switch. SeeIgnition Positions on
page 109.
Q. Climate Controls. SeeClimate Control System
on page 164.
R. Accessory Power Outlet. SeeAccessory Power
Outlet(s) on page 162.
S. Automatic Transaxle Shift Lever. SeeAutomatic
Transaxle Operation on page 113.
T. Glove Box. SeeGlove Box on page 140.
147

Hazard Warning Flashers
The hazard warning ashers let you warn others.
They also let police know you have a problem.
Your front and rear turn signal lamps will ash on
and off.
The hazard warning
asher button is located
on top of the steering
column.
The hazard warning ashers work no matter what
position the key is in, and even if the key is not in.
Press the button to make the front and rear turn
signal lamps ash. Press the button again to turn
the ashers off.
When the hazard warning ashers are on, the turn
signals will not work.
Other Warning Devices
If you carry reective triangles, you can set them up
at the side of the road about 300 feet (100 m)
behind your vehicle.
Horn
Press near or on the horn symbols on your
steering wheel pad to sound the horn.
Tilt Wheel
A tilt wheel allows you to adjust the steering wheel
before you drive. The steering wheel can be
raised to the highest level to give your legs more
room when you enter and exit the vehicle.
The tilt wheel lever is located on the left side of
the steering column.
148

To tilt the wheel, hold the wheel and pull the lever.
Then move the wheel to a comfortable position
and release the lever to lock the wheel in place.
Turn Signal/Multifunction Lever
The lever on the left side of the steering column
includes the following:
GTurn and Lane Change Signals. See
Turn and Lane-Change Signals on page 150.
2Headlamp High/Low-Beam Changer. See
Headlamp High/Low-Beam Changer on
page 151.
Flash-to-Pass. SeeFlash-to-Pass on page 151.
NWindshield Wipers. SeeWindshield Wipers
on page 151.
LQWindshield Washer. SeeWindshield
Washer on page 152.
For information on the headlamps, seeExterior
Lamps on page 156.
149

Turn and Lane-Change Signals
The turn signal has two upward (for right) and
two downward (for left) positions. These positions
allow you to signal a turn or a lane change.
To signal a turn, move the lever all the way up or
down. When the turn is nished, the lever will
return automatically.
An arrow on the
instrument panel
cluster will ash in
the direction of the
turn or lane change.
To signal a lane change, raise or lower the lever
until the arrow starts to ash. Hold it there until you
complete your lane change. The lever will return
by itself when you release it.If the arrow ashes faster than normal as you
signal a turn or a lane change, a signal bulb may
be burned out and other drivers won’t see
your turn signal.
If a bulb is burned out, replace it to help avoid an
accident. If the arrows don’t go on at all when
you signal a turn, check for burned-out bulbs and
then check the fuse. SeeFuses and Circuit
Breakers on page 395.
Turn Signal On Chime
If you leave either one of your turn signals on and
drive more than three-quarters of a mile (1.2 km),
a chime will sound to alert you.
150

Headlamp High/Low-Beam Changer
To change your headlamps from low beams to high
beams, or from high to low, pull the multifunction
lever all the way toward you. Then release it.
While the high beams
are on, this light will
appear on the
instrument panel cluster.
This light works only while the key is in RUN. The
fog lamps (if equipped) are not illuminated
when the high beams are on.
Flash-to-Pass
With the turn signal lever in the low-beam position,
pull the lever toward you briey to switch to
high-beam, (to signal you are going to pass).
If the headlamps are on, they will return to
low-beam when the lever is released.
This feature operates even if the headlamps are off.
Windshield Wipers
Be sure to clear ice and snow from the wiper
blades before using them. If they are frozen to the
windshield, gently loosen or thaw them. Damaged
wiper blades may not clear the windshield well,
making it harder to see and drive safely. If
the blades do become damaged, install new
blades or blade inserts. For more information, see
Windshield Wiper Blade Replacement on
page 347.
Heavy snow or ice can overload the wiper motor. A
circuit breaker will stop the motor until it cools down.
Clear away snow or ice to prevent an overload.
You control the windshield wipers by turning the
band with the wiper symbol on it.
8(Mist):For a single wiping cycle, turn the
band to mist. Hold it there until the wipers
start. Then let go. The wipers will stop after
one wipe. If you want more wipe cycles, hold
the band on mist longer.
151

6(Delay):You can set the wiper speed for a long
or short delay between wiping cycles. This can
be very useful in light rain or snow. Turn the band
to choose the delay time. The closer to the top
of the lever, the shorter the delay.
6(Low Speed):For steady wiping at low
speed, turn the band away from you to the
rst solid band past the delay settings.
1(High Speed):For high-speed wiping, turn
the band further, to the second solid band past the
delay settings.
9(Off):To stop the wipers, move the band to off.
Windshield Washer
At the top of the multifunction lever, there’s a
paddle with the windshield washer symbol on it.
To spray washer uid on the windshield, push the
paddle. The wipers will run for several sweeps and
then either stop or return to your preset speed. The
ignition key must be in ACCESSORY or RUN for
this to work. SeeWindshield Washer Fluid on
page 332.
{CAUTION:
In freezing weather, do not use your
washer until the windshield is warmed.
Otherwise the washer uid can form ice
on the windshield, blocking your vision.
When you are low on washer uid, a Washer Fluid
Low Add Fluid message will be lit in the Driver
Information Center (DIC) for 60 seconds. When the
ignition is turned off, a message will appear
again for three seconds as a reminder that
the uid level is low. For more information on
DIC messages, seeDIC Warnings and Messages
on page 195.
The washer uid message will no longer display
when the washer uid reservoir has been lled.
152