2007 CHEVROLET MONTE CARLO Owners Manual

Read the instructions completely before attempting
to program the Universal Home Remote.
Because of the steps involved, it may be helpful to
have another person available to assist you in
the programming steps.
Keep the original hand-held transmitter for use
in other vehicles as well as for future Universal
Home Remote programming. It is also
recommended that upon the sale of the vehicle,
the programmed Universal Home Remote buttons
should be erased for security purposes. See
“Erasing Universal Home Remote Buttons” later
in this section or, for assistance, seeCustomer
Assistance Offices on page 426.
Be sure that people and objects are clear of
the garage door or gate operator you are
programming. When programming a garage door,
it is advised to park outside of the garage.
It is recommended that a new battery be installed
in your hand-held transmitter for quicker and
more accurate transmission of the radio-frequency
signal.Programming Universal Home Remote
Follow these steps to program up to three channels:
1. Press and hold down the two outside
Universal Home Remote buttons, releasing
only when the Universal Home Remote
indicator light begins to ash, after
20 seconds. Do not hold down the buttons for
longer than 30 seconds and do not repeat
this step to program a second and/or
third hand-held transmitter to the remaining
two Universal Home Remote buttons.
2. Position the end of your hand-held transmitter
about 1 to 3 inches (3 to 8 cm) away from
the Universal Home Remote buttons
while keeping the indicator light in view.
3. Simultaneously press and hold both the
desired Universal Home Remote button
and the hand-held transmitter button. Do not
release the buttons until Step 4 has been
completed.
Some entry gates and garage door openers
may require you to substitute Step 3 with
the procedure noted in “Gate Operator and
Canadian Programming” later in this section.
137

4. The indicator light will ash slowly at rst and
then rapidly after Universal Home Remote
successfully receives the frequency signal
from the hand-held transmitter. Release both
buttons.
5. Press and hold the newly-trained Universal
Home Remote button and observe the
indicator light.
If the indicator light stays on continuously,
programming is complete and your device
should activate when the Universal Home
Remote button is pressed and released.
To program the remaining two Universal Home
Remote buttons, begin with Step 2 under
“Programming Universal Home Remote.”
Do not repeat Step 1 as this will erase all of
the programmed channels.
If the indicator light blinks rapidly for
two seconds and then turns to a constant light,
continue with Steps 6 through 8 following to
complete the programming of a rolling-code
device, most commonly, a garage door opener.6. Locate in the garage, the garage door opener
receiver (motor-head unit). Locate the “Learn”
or “Smart” button. This can usually be
found where the hanging antenna wire is
attached to the motor-head unit.
7. Firmly press and release the “Learn” or
“Smart” button. The name and color of
the button may vary by manufacturer.
You will have 30 seconds to start Step 8.
8. Return to the vehicle. Firmly press and hold
the programmed Universal Home Remote
button for two seconds, then release it.
Immediately press and hold the same
button a second time for two seconds, then
release it. Immediately, press and hold
the same button a third time for two seconds,
then release.
The Universal Home Remote should now
activate the rolling-code device.
To program the remaining two Universal
Home Remote buttons, begin with Step 2 of
“Programming Universal Home Remote.” You
do not want to repeat Step 1, as this will erase
all previous programming from the Universal
Home Remote buttons.
138

Gate Operator and Canadian
Programming
Canadian radio-frequency laws require transmitter
signals to time out or quit after several seconds
of transmission. This may not be long enough
for Universal Home Remote to pick up the signal
during programming. Similarly, some U.S. gate
operators are manufactured to time out in
the same manner.
If you live in Canada, or you are having difficulty
programming a gate operator or garage door
opener by using the “Programming Universal
Home Remote” procedures, regardless of where
you live, replace Step 3 under “Programming
Universal Home Remote” with the following:
Continue to press and hold the Universal Home
Remote button while you press and release every
two seconds (cycle) the hand-held transmitter
button until the frequency signal has been
successfully accepted by the Universal Home
Remote. The Universal Home Remote indicator
light will ash slowly at rst and then rapidly.
Proceed with Step 4 under “Programming
Universal Home Remote” to complete.
Using Universal Home Remote
Press and hold the appropriate Universal Home
Remote button for at least half of a second.
The indicator light will come on while the signal
is being transmitted.
Erasing Universal Home
Remote Buttons
To erase programming from the three Universal
Home Remote buttons do the following:
1. Press and hold down the two outside buttons
until the indicator light begins to ash, after
20 seconds. Do not hold the two outside
buttons for longer than 30 seconds.
2. Release both buttons.
The Universal Home Remote is now in the training
(learning) mode and can be programmed at any
time beginning with Step 2 under “Programming
Universal Home Remote” shown earlier in
this section.
Individual buttons cannot be erased, but they
can be reprogrammed. See “Reprogramming a
Single Universal Home Remote Button” following
this section.
139

Reprogramming a Single Universal
Home Remote Button
To program a device to Universal Home Remote
using a Universal Home Remote button
previously trained, follow these steps:
1. Press and hold the desired Universal Home
Remote button. Do not release the button.
2. The indicator light will begin to ash after
20 seconds. While still holding the Universal
Home Remote button, proceed with
Step 2 under “Programming Universal Home
Remote” shown earlier in this section.
For additional information on Universal Home
Remote, seeCustomer Assistance Offices
on page 426.
Storage Areas
Glove Box
To open the glove box, lift up on the lever.
Cupholder(s)
Your vehicle is equipped with cupholders located
between the front seats and in the rear seat armrest.
Center Console Storage Area
The console has cupholders and a storage area.
To open the console’s storage area, press the
latch located toward the front of the console lid on
the driver’s side of the vehicle.
Rear Seat Armrest
Your vehicle has a rear seat armrest with
cupholders. To access, pull the tab on the
armrest forward.
140

Convenience Net
The vehicle may have a convenience net located
on the back wall of the trunk.
The net is not for larger, heavier loads. Store
those in the trunk as far forward as possible.
Unhook the net so that it will lie at when not in use.
Sunroof
If your vehicle has this
feature, the sunroof
switches are located on
the overhead console.
The sunroof can only be operated when the
ignition is in ACCESSORY, RUN, or when
Retained Accessory Power (RAP) is active. See
Retained Accessory Power (RAP) on page 110.
Q(Vent/Express-Open):To vent the sunroof
when it is closed, press this switch once.
When using the vent, the sunshade should be fully
opened. The sunshade can be opened or closed
manually by sliding it rearward or forward.
From the vent position, press this switch again to
activate the express-open feature. Press the
close switch to stop movement of the sunroof.
The sunshade will automatically open when using
express-open.
R(Close):To close the sunroof, press and hold
this switch until the sunroof motor stops, or
release the switch when the desired position has
been reached.
141

✍NOTES
142

Instrument Panel Overview........................ 146
Hazard Warning Flashers.......................... 148
Other Warning Devices............................. 148
Horn.......................................................... 148
Tilt Wheel.................................................. 148
Turn Signal/Multifunction Lever.................. 149
Turn and Lane-Change Signals................. 150
Headlamp High/Low-Beam Changer.......... 151
Flash-to-Pass............................................ 151
Windshield Wipers..................................... 151
Windshield Washer.................................... 152
Cruise Control........................................... 153
Exterior Lamps.......................................... 156
Delayed Headlamps.................................. 157
Daytime Running Lamps (DRL)/
Automatic Headlamp System.................. 158
Fog Lamps................................................ 158
Instrument Panel Brightness...................... 159
Courtesy Lamps........................................ 159
Dome Lamp.............................................. 159
Entry Lighting............................................ 160
Delayed Entry Lighting.............................. 160
Delayed Exit Lighting................................. 160
Parade Dimming........................................ 161Reading Lamps......................................... 161
Electric Power Management...................... 161
Battery Run-Down Protection..................... 162
Accessory Power Outlet(s)........................ 162
Ashtray(s) and Cigarette Lighter................ 164
Climate Controls......................................... 164
Climate Control System............................. 164
Outlet Adjustment...................................... 168
Passenger Compartment Air Filter............. 169
Warning Lights, Gages, and Indicators..... 170
Instrument Panel Cluster........................... 171
Speedometer and Odometer...................... 172
Tachometer............................................... 172
Safety Belt Reminder Light........................ 173
Passenger Safety Belt Reminder Light....... 173
Airbag Readiness Light............................. 174
Passenger Airbag Status Indicator............. 175
Charging System Light.............................. 177
Brake System Warning Light..................... 177
Anti-Lock Brake System Warning Light...... 178
Traction Control System (TCS)
Warning Light........................................ 179
Engine Coolant Temperature
Warning Light........................................ 179
Section 3 Instrument Panel
143

Engine Coolant Temperature Gage............ 180
Tire Pressure Light.................................... 180
Malfunction Indicator Lamp........................ 181
Oil Pressure Light..................................... 184
Security Light............................................ 184
Fog Lamp Light......................................... 185
Cruise Control Light.................................. 185
Highbeam On Light................................... 185
Fuel Gage................................................. 185
Driver Information Center (DIC).................. 186
DIC Operation and Displays...................... 187
DIC Compass............................................ 193
DIC Warnings and Messages.................... 195
DIC Vehicle Customization........................ 203Audio System(s)......................................... 210
Setting the Time (Without Date Display).... 211
Setting the Time (With Date Display)......... 212
Radio with CD (Base)............................... 214
Radio with CD (MP3)................................ 220
Using an MP3........................................... 231
XM Radio Messages................................. 238
Theft-Deterrent Feature............................. 240
Audio Steering Wheel Controls.................. 240
Radio Reception........................................ 241
Care of Your CDs..................................... 242
Care of the CD Player.............................. 242
Backglass Antenna.................................... 242
XM™ Satellite Radio Antenna System....... 243
Section 3 Instrument Panel
144