2007 Acura RDX light

Check the fluid level in the
windshield washer reservoir at least
monthly during normal use.
To check the
windshield washer fluid level, open
the hood and look the windshield
washer reservoir located behind the
left headlight. You will see a ‘‘1/2’’
mark on the reservoir.
You will see a ‘‘WASHER FLUID
LOW’’ message on the multi-
info rmation display (see page ).
The
washer level indicator will come
on when the level is low (see page
).
85
74
On U.S. models:
On Canadian RDX with TechnologyPackage model
On Canadian RDX model
CONT INUED
Windshield Washers
Maint enance
353
WASHER LEVEL INDICATOR
Front
WINDSHIELD WASHER RESERVOIR
——
y
y
() yy

Theheadlightswereproperlyaimed
when your vehicle was new. If you
regularly carry heavy items in the
cargo area or pull a trailer,
readjustment may be required.
Adjustmentsshouldbedonebyyour
dealer or other qualif ied technician.
The low beam headlight bulbs are a
type of high voltage discharge tube.
High voltage can remain in the
circuit even with the light switch of f
and the key removed. Because of
this, you should not attempt to
examine or change a low beam
headlight bulb yourself . If a low
beam headlight bulb fails, take the
vehicle to your dealer to have it
replaced.Your vehicle has halogen headlight
bulbs. When replacing a bulb, handle
it by its base, and protect the glass
f rom contact with your skin or hard
objects. If you touch the glass, clean
it with denatured alcohol and a clean
cloth.
Insert the new bulb into the hole,
and turn it one-quarter turn
clockwise to lock it in place.
Push the electrical connector onto
the new bulb.
Turn on the headlights to test the
new bulb.
Remove the bulb by turning it
about one-quarter turn
counterclockwise. Remove the electrical connector
f rom the bulb by pushing on the
tab and pulling the connector
down. Open the hood.
1.
2. 3.
4.
5.
Headlight A iming
L ow Beam Headlight Bulb
Replacement
Replacing a High Beam Headlight
Bulb
Lights
Maint enance
359
BULB
CONNECTORHalogen headlight bulbs get very hot
when lit. Oil, perspiration, or a scratch
on the glass can cause the bulb to
overheat and shatter.
——
y
y
() yy

Test the lights to make sure the
new bulb is working.
Insert the socket back into the
headlight assembly. Turn it
clockwise to lock it in place.
Open the hood. Remove the
socket f rom the headlight
assembly by turning it one-quarter
turn counterclockwise.
Pull the bulb straight out of its
socket. Push the new bulb straight
into the socket until it bottoms.Install the socket back into the
headlight assembly. Turn it
clockwise to lock it in place.
Install the new bulb in the socket.
Turn it clockwise to lock it in place. Remove the bulb f rom the socket
by pushing the bulb in and turning
it counterclockwise until it unlocks. Open the hood. Remove the
socket f rom the headlight
assembly by turning it one-quarter
turn counterclockwise. Turn on the lights to make sure
the new bulb is working.
1.
2.
3. 1.
2. 4.
5.
3.
4.
Lights
Replacing a Front Side Marker
Light Bulb
Replacing a Front T urn Signal/
Parking L ight Bulb
360
BULB
SOCKET BULB
SOCKET
——
y
y
() yy

Open the tailgate. Place a cloth on
the edge of the light assembly
cover. Remove the cover by
caref ully prying in the notch on its
middle edge with a f lat-tip
screwdriver.
Determine which of the two bulbs
is burned out: taillight or back-up
light.Remove the socket by turning it
one-quarter turn counterclockwise.
Pull the bulb straight out of its
socket. Push the new bulb straight
into the socket until it bottoms.Turn on the lights to make sure
the new bulb is working.
Reinstall the socket into the light
assembly by turning it clockwise
until it locks.
Reinstall the light assembly cover.
1.
2. 3.
4.5.
6.
7.
Lights
Replacing Rear Bulbs
(in Tailgate)
Maint enance
361
COVER
NOTCH SOCKETS
BULBS
——
y

y
() yy

Remove the two bolt covers on the
rear pillar by prying on the bottom
edge with a flat-tip screwdriver.
Remove the bolts with a Phillips-
head screwdriver, and remove the
light assembly f rom the rear pillar.Determine which of the three
bulbs is burned out: brake/
taillight, turn signal or rear side
marker.
Remove the socket by turning it
one-quarter turn counterclockwise.
Pull the bulb straight out of its
socket. Push the new bulb straight
into the socket until it bottoms.Turn on the lights to make sure
the new bulb is working.
Put the socket back into the light
assembly, and turn it clockwise to
lock it in place.
Install the rear light assembly in
the rear pillar. Tighten the two
bolts. Snap the bolt covers into
position.
Open the tailgate.
2.
4.
5.6.
7.
8.
3.
1.
Lights
Replacing Rear Bulbs
(in Rear Pillar)
362
COVERS BOLTS
BULBSOCKET
——
y
y
() yy

CONT INUED
Your vehicle uses halogen light
bulbs. When replacing a bulb, handle
it by its plastic case, and protect the
glass from contact with your skin or
hard objects. If you touch the glass,
clean it with denatured alcohol and a
clean cloth.Use a Phillips-head screwdriver to
remove the screw and use the flat-
tipped screwdriver to remove the
holding clip located under the
f ront bumper.Remove the electrical connector
f rom the bulb by pushing on the
tab and pulling the connector
down.
Remove the bulb f rom the f og
light assembly by turning it one-
quarter turn counterclockwise.
Push up the undercover.
1.
2. 3.
4.
Lights
Replacing a Front Fog L ight Bulb
Maint enance
363
BULB
CONNECTOR
HOLDING CLIP
SCREW
Halogen bulbs get very hot when lit.
Oil, perspiration, or a scratch on the
glass can cause the bulb to overheat
and shatter.
——
y

y
() yy

Install the new bulb into the hole
and turn it one-quarter turn
clockwise to lock it in place.
Push the electrical connector back
onto the bulb. Make sure it is on
all the way.
Turn on the f og lights to test the
new bulb.
Put the undercover in place.
Reinstall the clip, and tighten the
screw securely.Remove the two screw covers on
the light assembly by prying on
the side edge with a flat-tip
screwdriver.
Remove the screws with a Phillips-
head screwdriver, then remove
the light assembly f rom the
tailgate.Remove the socket f rom the light
assembly by turning it one-quarter
turn counterclockwise.
Pull the bulb straight out of its
socket. Push the new bulb straight
into the socket until it bottoms.
5.
6.
7.
8.
1.
2.3.
4.
Lights
Replacing a High-mount Brake
Light Bulb
364
COVERS SOCKET
BULB
SCREWS
——
y

y
() yy

Press the brake pedal to make
sure the new bulb is working.
Put the socket back into the light
assembly, and turn it clockwise to
lock it in place.Each outside mirror has side turn
signal lights. The lights should be
replaced by your dealer.
The license plate has two lights
above it. The bulbs should be
replaced by your dealer.
Reinstall the high-mount brake
light assembly into the tailgate.
Tighten the two screws and
reinstall the covers.
6. 5.
7.
Lights
Side T urn Signal L ight
Replacing a Rear License Plate
Light Bulb
Maint enance
365
——
y
y
() yy