AX–170U151F AUTOMATIC TRANSAXLE – DIFFERENTIAL OIL SEAL
AX
REPLACEMENT
1. REPLACE TRANSAXLE HOUSING OIL SEAL LH
(a) Drain the automatic transaxle fluid.
(1) Remove the drain plug and gasket, and drain
the ATF.
(2) Install a new gasket and drain plug.
Torque: 47 N*m (479 kgf*cm, 35 ft.*lbf)
(b) Remove the front drive shaft LH (see page DS-41).
(c) Remove the transaxle housing oil seal LH.
(1) Using SST, tap out the oil seal.
SST 09308-00010
(d) Install a new transaxle housing oil seal LH.
(1) Coat the lip of a new oil seal with MP grease.
(2) Using SST and a hammer, tap in the oil seal.
SST 09223-15020, 09950-70010 (09951-
07200)
Standard depth:
0 +-0.5 mm (0 +-0.020 in.)
(e) Install the front drive shaft LH (see page DS-66).
(f) Add automatic transaxle fluid.
Fluid type:
Toyota Genuine ATF WS
(g) Inspect the transaxle fluid level (see page AX-126).
2. REPLACE TRANSAXLE HOUSING OIL SEAL RH
(a) Remove the engine assembly with transaxle (see
page EM-21).
(b) Drain the automatic transaxle fluid.
(1) Remove the drain plug and gasket, and drain
the ATF.
(2) Install a new gasket and the drain plug.
Torque: 47 N*m (479 kgf*cm, 35 ft.*lbf)
(c) Remove the 3 bolts and drive shaft bearing bracket.
(d) Remove the 3 bolts and rear engine mounting
bracket.
(e) Remove the transfer assembly (see page TF-59).
D025835E01
D025836E01
ES–542AZ-FE ENGINE CONTROL SYSTEM – SFI SYSTEM
ES
HINT:
• *1: If no idling conditions are specified, the transmission
gear selector lever should be in the N or P position, and
the A/C switch and all accessory switches should be OFF.
• *2: DATA LIST values are only displayed when performing
the following ACTIVE TEST: VVT B1. For other ACTIVE
TESTs, the DATA LIST value will be 0.
2. ACTIVE TEST
HINT:
Performing an ACTIVE TEST enables components
including the relays, VSV (Vacuum Switching Valve) and
actuators, to be operated without removing any parts.
The ACTIVE TEST can be performed with the intelligent
tester. Performing the ACTIVE TEST as the first step of
troubleshooting is one method of shortening diagnostic
time.
DATA LIST can be displayed during ACTIVE TEST.
(a) Connect the intelligent tester to the DLC3.
(b) Turn the ignition switch ON.
CCM CMPLComprehensive component
monitor:
COMPL or INCMPL--
FUEL ENAFuel system monitor:
UNABLE or ENABLE--
FUEL CMPLFuel system monitor:
COMPL or INCMPL--
MISFIRE ENAMisfire monitor:
UNABLE or ENABLE--
MISFIRE CMPLMisfire monitor:
COMPL or INCMPL--
HTR ENAO2S (A/FS) heater monitor:
UNABLE or ENABLE--
HTR CMPLO2S (A/FS) heater monitor:
COMPL or INCMPL--
O2S (A/FS) ENAO2S (A/FS) monitor:
UNABLE or ENABLE--
O2S (A/FS) CMPLO2S (A/FS) monitor:
COMPL or INCMPL--
EVAP ENAEVAP monitor:
UNABLE or ENABLE--
EVAP CMPLEVAP monitor:
COMPL or INCMPL--
CAT ENACatalyst monitor:
UNABLE or ENABLE--
CAT CMPLCatalyst monitor:
COMPL or INCMPL--
MODEL CODE Identifying model code ACA3# -
ENGINE TYPE Identifying engine type 2AZFE -
CYLINDER NUMBERIdentifying cylinder number:
Min.: 0, Max.: 2554-
TRANSMISSION Identifying transmission type 4AT -
DESTINATION Identifying destination A (America) -
MODEL YEARIdentifying model year:
Min.: 1900, Max.: 2155200# -
SYSTEM Identifying engine system GASLIN (gasoline engine) -Intelligent Tester Display Measurement: Range (Display) Normal Condition*1 Diagnostic Note
