2006 SUZUKI SX4 engine

Downloaded from www.Manualslib.com manuals search engine Engine General Information and Diagnosis: 1A-183
Reference waveform No.5
Ignition coil No.2 and No.3 signal (2) with engine idling
Reference waveform No.6
Ignition coil signal (1) with engine idlingReference waveform No.7
Ignition coil No.1 and No.4 signal (2) with engine idling Measurement
terminalCH1: “C01-20” to “C01-58”
CH2: “C01-5” to “C01-58”
Oscilloscope
settingCH1: 2 V/DIV, CH2: 2 V/DIV
TIME: 40 ms/DIV
Measurement
condition• After warmed up to normal
operating temperature
• Engine at specified idle speed
[A]: For VVT model
[B]: For non-VVT model
1. Cylinder reference signal (CMP reference signal)
3. 720° crank angle
Measurement
terminalCH1: “C01-6” to “C01-58”
Oscilloscope
settingCH1: 2 V/DIV
TIME: 4 ms/DIV
Measurement
condition• After warmed up to normal
operating temperature
• Engine at specified idle speed
I4RS0B110054-01
2. 4 – 6 V 3. Ignition coil pulse width: 4 – 5 msec.
Measurement
terminalCH1: “C01-20” to “C01-58”
CH2: “C01-6” to “C01-58”
Oscilloscope
settingCH1: 2 V/DIV, CH2: 2 V/DIV
TIME: 40 ms/DIV
Measurement
condition• After warmed up to normal
operating temperature
• Engine at specified idle speed
[A]: For VVT model
[B]: For non-VVT model
1. Cylinder reference signal (CMP reference signal)
3. 720° crank angle
I4RS0B110055-02
I4RS0B110056-01

Downloaded from www.Manualslib.com manuals search engine 1A-184 Engine General Information and Diagnosis:
Reference waveform No.8
Heated oxygen sensor-1 signal (1) with engine idling
Reference waveform No.9
Heated oxygen sensor-1 heater signal (2) with engine
idlingReference waveform No.10
Heated oxygen sensor-2 heater signal (4) with engine
idling
Measurement
terminalCH1: “C01-10” to “C01-57”
CH2: “C01-46” to “C01-58”
Oscilloscope
settingCH1: 500 mV/DIV, CH2: 20 V/DIV
TIME: 1 s/DIV
Measurement
condition• After warmed up to normal
operating temperature
• Engine at specified idle speed
2. Heated oxygen sensor-1 heater signal
Measurement
terminalCH1: “C01-10” to “C01-57”
CH2: “C01-46” to “C01-58”
Oscilloscope
settingCH1: 500 mV/DIV, CH2: 10 V/DIV
TIME: 200 ms/DIV
Measurement
condition• After warmed up to normal
operating temperature
• Engine at specified idle speed
1. Heated oxygen sensor-1 signal 4. ON signal
3. OFF signal 5. One duty cycle
I4RS0B110058-01
I4RS0B110059-01
Measurement
terminalCH1: “C01-11” to “C01-57”
CH2: “C01-47” to “C01-58”
Oscilloscope
settingCH1: 500 mV/DIV, CH2: 10 V/DIV
TIME: 2 s/DIV
Measurement
condition• After warmed up to normal
operating temperature
• Vehicle driving at 60 km/h (37
mph) for 10 min.
• Engine at specified idle speed
1. Heated oxygen sensor-2 signal upper limit
2. Heated oxygen sensor-2 signal lower limit
3. Normal waveform range
I4RS0B110060-01

Downloaded from www.Manualslib.com manuals search engine Engine General Information and Diagnosis: 1A-185
Reference waveform No.11
No.3 fuel injector signal (2) with engine idlingReference waveform No.12
No.4 fuel injector signal (2) with engine idling
Measurement
terminalCH1: “C01-20” to “C01-58”
CH2: “C01-16” to “C01-58”
Oscilloscope
settingCH1: 5 V/DIV, CH2: 20 V/DIV
TIME: 40 ms/DIV
Measurement
condition• After warmed up to normal
operating temperature
• Engine at specified idle speed
[A]: For VVT model
[B]: For non-VVT model
1. Cylinder reference signal (CMP reference signal)
3. 720° crank angle
I4RS0B110062-01
Measurement
terminalCH1: “C01-20” to “C01-58”
CH2: “C01-17” to “C01-58”
Oscilloscope
settingCH1: 5 V/DIV, CH2: 20 V/DIV
TIME: 40 ms/DIV
Measurement
condition• After warmed up to normal
operating temperature
• Engine at specified idle speed
[A]: For VVT model
[B]: For non-VVT model
1. Cylinder reference signal (CMP reference signal)
3. 720° crank angle
I4RS0B110063-01

Downloaded from www.Manualslib.com manuals search engine 1A-186 Engine General Information and Diagnosis:
Reference waveform No.13
CMP sensor signal with engine idlingReference waveform No.14
CMP sensor signal with engine idling
Measurement
terminalCH1: “C01-20” to “C01-58”
CH2: “C01-21” to “C01-58”
Oscilloscope
settingCH1: 2 V/DIV, CH2: 2 V/DIV
TIME: 20 ms/DIV
Measurement
condition• After warmed up to normal
operating temperature
• Engine at specified idle speed
[A]: For VVT model
[B]: For non-VVT model
1. Cylinder reference signal (CMP reference signal)
2. CKP signal
3. 360° crank angle
4. 4 – 5 V
5. 36 – 6 = 30 CKP pulse
I4RS0B110064-01
Measurement
terminalCH1: “C01-20” to “C01-58”
CH2: “C01-21” to “C01-58”
Oscilloscope
settingCH1: 2 V/DIV, CH2: 2 V/DIV
TIME: 10 ms/DIV
Measurement
condition• After warmed up to normal
operating temperature
• Engine at specified idle speed
[A]: For VVT model
[B]: For non-VVT model
1. Cylinder reference signal (CMP reference signal)
2. CKP signal
3. 30° crank angle
4. 10° crank angle
5. 360° crank angle
6. 36 – 6 = 30 CKP pulse
I4RS0B110065-01

Downloaded from www.Manualslib.com manuals search engine Engine General Information and Diagnosis: 1A-187
Reference waveform No.15
Mass air flow sensor signal (1) with engine racing
Reference waveform No.16
EVAP canister purge valve signalReference waveform No.17
Manifold absolute pressure sensor signal (1) with
ignition switch turned ON
Reference waveform No.18
Manifold absolute pressure sensor signal (1) with engine
racing Measurement
terminalCH1: “C01-26” to “C01-27”
CH2: “C01-54” to “C01-55”
Oscilloscope
settingCH1: 1 V/DIV, CH2: 1 V/DIV
TIME: 200 ms/DIV
Measurement
condition• After warmed up to normal
operating temperature
• Engine racing
2. Throttle position sensor signal
3. Racing
4. Idle
Measurement
terminalCH1: “C01-29” to “C01-58”
Oscilloscope
settingCH1: 10 V/DIV
TIME: 40 ms/DIV
Measurement
condition• After warmed up to normal
operating temperature
• EVAP canister purge valve setting
at 52% by using “Engine / Active
Test” of scan tool.
1. ON signal 3. One duty cycle
2. OFF signal 4. 10 – 14 V
I4RS0B110066-01
I4RS0B110067-01
Measurement
terminalCH1: “C01-53” to “C01-55”
CH2: “C01-54” to “C01-55”
Oscilloscope
settingCH1: 2 V/DIV, CH2: 1 V/DIV
TIME: 200 ms/DIV
Measurement
condition• After warmed up to normal
operating temperature
• Ignition switch turned ON
2. Throttle position sensor signal
Measurement
terminalCH1: “C01-53” to “C01-55”
CH2: “C01-54” to “C01-55”
Oscilloscope
settingCH1: 2 V/DIV, CH2: 2 V/DIV
TIME: 200 ms/DIV
Measurement
condition• After warmed up to normal
operating temperature
• Engine racing
2. Throttle position sensor signal
3. Racing
4. Idle
I4RS0B110070-01
I4RS0B110071-01

Downloaded from www.Manualslib.com manuals search engine 1A-188 Engine General Information and Diagnosis:
Reference waveform No.19
Knock sensor signal at engine speed 4000 r/min.
Reference waveform No.20
Knock sensor signal at engine speed 4000 r/min.Reference waveform No.21
Oil control valve signal with engine idling (for engine with
VVT system)
Reference waveform No.22
Oil control valve signal with engine racing (for engine
with VVT system) Measurement
terminalCH1: “C01-56” to “C01-58”
Oscilloscope
settingCH1: 1 V/DIV
TIME: 10 ms/DIV
Measurement
condition• After warmed up to normal
operating temperature
• Engine running at 4000 r/min.
Measurement
terminalCH1: “C01-56” to “C01-58”
Oscilloscope
settingCH1: 1 V/DIV
TIME: 200 µs/DIV
Measurement
condition• After warmed up to normal
operating temperature
• Engine running at 4000 r/min.
I4RS0B110072-01
I4RS0B110073-01
Measurement
terminalCH1: “C01-60” to “C01-59”
Oscilloscope
settingCH1: 5 V/DIV
TIME: 2 ms/DIV
Measurement
conditionAt the moment of the ignition switch
turned on
1. ON signal 3. Only duty cycle
2. OFF signal
Measurement
terminalCH1: “C01-60” to “C01-59”
Oscilloscope
settingCH1: 5 V/DIV
TIME: 400 µs/DIV
Measurement
condition• After warmed up to normal
operating temperature
• Vehicle running at 20 km/h (12
mph) and depress accelerator
pedal fully
1. Accelerator pedal depressed fully 4. ON signal
2. Accelerator pedal depressed partially 5. OFF signal
3. Oil control valve signal
I4RS0B110074-01
I4RS0B110075-01

Downloaded from www.Manualslib.com manuals search engine Engine General Information and Diagnosis: 1A-189
Reference waveform No.23
CAN communication line signal from ABS / ESP®
control module assembly or TCM with ignition switch
turned ONReference waveform No.24
Ignition pulse (engine revolution) signal (2) with engine
idling
Measurement
terminalCH1: “E01-3” to “C01-58” / CH1:
“C01-13” to “C01-58”
CH2: “E01-18” to “C01-58” / CH2:
“C01-12” to “C01-58”
Oscilloscope
settingCH1: 1 V/DIV, CH2: 1 V/DIV
TIME: 40 µs/DIV
Measurement
conditionIgnition switch turned ON
(Signal pattern is depending on
engine condition)
1. CAN communication line signal (High)
2. CAN communication line signal (Low)
I4RS0B110076-01
Measurement
terminalCH1: “C01-20” to “C01-58”
CH2: “E01-4” to “C01-58”
Oscilloscope
settingCH1: 5 V/DIV, CH2: 5 V/DIV
TIME: 40 ms/DIV
Measurement
condition• After warmed up to normal
operating temperature
• Engine at specified idle speed
[A]: For VVT model
[B]: For non-VVT model
1. Cylinder reference signal (CMP reference signal)
3. 720° crank angle
I4RS0B110077-01

Downloaded from www.Manualslib.com manuals search engine 1A-190 Engine General Information and Diagnosis:
Reference waveform No.25
Ignition pulse (engine revolution) signal (2) with engine
idling
Reference waveform No.26
Throttle actuator output signal with ignition switch turned
ONReference waveform No.27
Throttle actuator output signal with ignition switch turned
ON Measurement
terminalCH1: “C01-20” to “C01-58”
CH2: “E01-4” to “C01-58”
Oscilloscope
settingCH1: 5 V/DIV, CH2: 5 V/DIV
TIME: 10 ms/DIV
Measurement
condition• After warmed up to normal
operating temperature
• Engine at specified idle speed
[A]: For VVT model
[B]: For non-VVT model
1. Cylinder reference signal (CMP reference signal)
3. 360° crank angle
4. 2 to 4 msec.
5. 10 – 14 V
Measurement
terminalCH1: “C01-45” to “C01-58”
CH2: “C01-44” to “C01-58”
Oscilloscope
settingCH1: 5 V/DIV, CH2: 5 V/DIV
TIME: 2 ms/DIV
Measurement
condition• After warmed up to normal
operating temperature
• Ignition switch turned ON and
accelerator pedal at idle position
I4RS0B110078-01
1. Throttle actuator drive signal (“C01-45” terminal)
2. Throttle actuator drive signal (“C01-44” terminal)
3. ON signal
4. OFF signal
5. One duty cycle
Measurement
terminalCH1: “C01-45” to “C01-58”
CH2: “C01-44” to “C01-58”
Oscilloscope
settingCH1: 5 V/DIV, CH2: 5 V/DIV
TIME: 2 ms/DIV
Measurement
condition• After warmed up to normal
operating temperature
• Ignition switch turned ON and
accelerator pedal at full
depressed position
1. Throttle actuator drive signal (“C01-45” terminal)
2. Throttle actuator drive signal (“C01-44” terminal)
3. ON signal
4. OFF signal
5. One duty cycle
I4RS0B110081-02
I4RS0B110082-02