2006 NISSAN VERSA wheel torque

IDX-6
ALPHABETICAL INDEX
R
Radiator ............................................................ CO-11
Rear axle .......................................................... RAX-4
Rear combination lamp removal and installation LT-87
Rear door .......................................................... GW-47
Rear seat belt ...................................................... SB-6
Rear suspension ............................................... RSU-5
Rear washer .................................................... WW-30
Rear window defogger ...................................... GW-50
Rear wiper ....................................................... WW-30
Refrigerant connection precaution .................... MTC-5
Refrigerant discharging evacuating charging . MTC-80
Refrigerant general precaution ......................... MTC-5
Refrigerant lines .............................................. MTC-80
Refrigerant pressure sensor ............. EC-586, MTC-88
Refrigeration cycle .......................................... MTC-16
Remote keyless entry system ............................ BL-54
Removal and installation (A/T) ......................... AT-253
Reverse idler shaft (M/T) ................................... MT-18
Reverse lamp switch (M/T) - See Back-up lamp switch
(M/T) .................................................................. MT-11
Reverse main gear (M/T) ................................... MT-18
Road test ......... AT-58, AT-61, AT-64, AT-65, CVT-46
Room lamp - See Interior lamp ........................... LT-91
RP/SEN - Wiring diagram ................................ EC-587
S
SAE J1979 - Service $01 - 09 ........................... EC-47
Seat belt inspection ................................ SB-8, MA-27
Seat belt, front ..................................................... SB-3
Seat belt, rear ...................................................... SB-6
Secondary pressure sensor ........................... CVT-129
Secondary Speed Sensor ................................ CVT-95
SECPS - Wiring diagram ............................... CVT-130
SECPSV - Wiring diagram ............................. CVT-125
Self-diagnostic results .......................... EC-64, EC-116
SEN/PW - Wiring diagram ............................... EC-431
SESCVT - Wiring diagram ............................... CVT-96
SHIFT - Wiring diagram ................... AT-236, CVT-198
Shift control ...................................................... CVT-26
Shift control components (M/T) .......................... MT-21
Shift control system ....................................... CVT-191
Shift fork (M/T) ................................................... MT-21
Shift lever ........................................................... MT-12
Shift lock system .............................................. AT-235
Shift schedule ..................... AT-67, CVT-53, CVT-210
Shock absorber (rear) ....................................... RSU-9
Side air bag (satellite) sensor ......................... SRS-50
Side curtain air bag ......................................... SRS-47
Side trim .............................................................. EI-32
SMJ (super multiple junction) ............................ PG-75
Specification value ........................................... EC-133
Speedometer ........................................................ DI-5
Spiral cable ..................................................... SRS-44
Spot lamp .......................................................... LT-107
SPSW - Wiring diagram ................................. CVT-171
SROOF - Wiring diagram ................................... RF-13
SRS - See Supplemental Restraint System ...... SRS-4
SRS - Wiring diagram ..................................... SRS-13
SRS Trouble diagnoses .................................... SRS-9
SSV/A - Wiring diagram ................................... AT-152
SSV/B - Wiring diagram ................................... AT-157
Stall Test ......................................................... CVT-43
Stall test (A/T) .................................................... AT-53
START - Wiring diagram ................................... SC-12
Starting system ................................................. SC-10
Steering linkage ................................................. PS-12
Steering wheel and column ........................ PS-6, PS-9
Steering wheel turning force ................................ PS-6
Step motor .................................... CVT-164, CVT-168
STM - Wiring diagram ................................... CVT-165
Stop lamp ................................................ LT-71, LT-87
Stop lamp switch ............................................. EC-488
STOP/L - Wiring diagram ................................... LT-71
STSIG - Wiring diagram .................................. CVT-73
Sun roof, electric ................................................ RF-10
Sunroof .................................................. RF-10, RF-22
Supplemental Restraint System ........................ SRS-4
Suspension ....................................................... MA-26
Swirl control valve ........................................... EC-592
Symbols and abbreviations ...................... GI-10, GI-23
Symptom matrix chart ....................................... EC-92
Synchronizer (M/T) ........................................... MT-18
System readiness test (SRT) code ................... EC-52
T
Tachometer ........................................................... DI-5
Tail lamp ............................................................ LT-87
TAIL/L - Wiring diagram ..................................... LT-78
TCM circuit diagram ........................................ CVT-42
TCM function ................................................... CVT-24
TCM inspection table ........................... AT-78, CVT-54
TCV - Wiring diagram ...................... AT-135, CVT-106
Telephone .......................................................... AV-49
Theft warning system - See Vehicle security (Theft warn-
ing) system ....................................................... BL-193
Thermo control amp ........................................ MTC-63
Thermostat ........................................................ CO-18
Three way catalyst function ............................ EC-334
Three way catalyst precautions ............................ GI-5
Throttle control motor relay ............................. EC-493
Throttle position sensor (TPS) .. EC-206, EC-302, EC-
460, EC-462, EC-526
Throttle valve closed position learning .............. EC-78
Tie-rod ................................................................ PS-12
Timing chain ...................................................... EM-37
TLID - Wiring diagram ...................................... BL-177
Torque converter installation .... AT-254, AT-369, CVT-
208
Torque convertor clutch solenoid valve CVT-105, CVT-
110
TPS1 - Wiring diagram .................................... EC-304
TPS2 - Wiring diagram .................................... EC-208
TPS3 - Wiring diagram .................................... EC-528
Transmission case (M/T) .................................. MT-17

MA-24
CHASSIS AND BODY MAINTENANCE
Revision: June 20062007 Versa
Balancing WheelsELS0022E
Adjust wheel balance using road wheel center.
CAUTION:

Be careful not to scratch the road wheel during removal.

Use clip-on type wheel balance weights only.
Wheel balance (Maximum allowable unbalance):
RotationELS0022F

Follow the maintenance schedule for tire rotation service inter-
vals. Refer to MA-7, "
PERIODIC MAINTENANCE" .

Do not include the T-type spare tire when rotating tires.
CAUTION:

When installing wheels, tighten them diagonally by divid-
ing the work two to three times in order to prevent the
wheels from developing any distortion.

Be careful not to tighten wheel nut at torque exceeding
the specification to prevent damage of disc rotor.
Checking Brake Fluid Level and LeaksELS0022G

If fluid level is extremely low, check brake system for leaks.
Checking Brake Lines and CablesELS0022H

Check brake fluid lines and parking brake cables for improper
attachment, leaks, chafing, abrasions, deterioration, etc.
Maximum allowable unbalanceDynamic (At rim flange) Less than 5 g (0.18 oz) (one side)
Static (At rim flange) Less than 10 g (0.35 oz)
Wheel nut : 113 N·m (12 kg-m, 83 ft-lb)SM A82 9C
SBR4 51 D
SBR3 89 C

PS-4
PREPARATION
Revision: June 20062007 Versa
PREPARATIONPFP:00002
Special Service ToolsEGS0014S
The actual shapes of Kent-Moore tools may differ from those of special tools illustrated here.
Commercial Service ToolsEGS0014T
Tool number
(Kent-Moore No.)
Tool nameDescription
ST3127S000
(J-25742-1)
Preload gauge
(J-25765-A)
1. GG91030000
Torque wrench
2. HT62940000
(—)
Socket adapter (1/2")
3. HT62900000
(—)
Socket adapter (3/8")Inspecting rotating torque for steering column
assembly and pinion assembly
KV40107300
(—)
Boot Band crimping toolInstalling boot bands
KV48103400
(—)
Preload adapterInspecting of rotating torque for pinion assem-
bly
S-NT541
ZZA1229D
ZZA0824D
Tool number
Tool nameDescription
Spring gauge Inspecting steering wheel turning force and
power steering gear linkage
Power toolRemoving nuts and bolts
LST025
PBIC0190E

NOISE, VIBRATION AND HARSHNESS (NVH) TROUBLESHOOTING
PS-5
C
D
E
F
H
I
J
K
L
MA
B
PS
Revision: June 20062007 Versa
NOISE, VIBRATION AND HARSHNESS (NVH) TROUBLESHOOTINGPFP:00003
NVH Trouble Shooting ChartEGS0014U
Use chart below to help you find the cause of the symptom. If necessary, repair or replace these parts.
×: ApplicableReference page
PS-14PS-14PS-6PS-6PS-6PS-10
PS-12
, PS-13PS-10PS-9PS-13
FA X-4, "
NVH Troubleshooting Chart
"
FSU-5, "
NVH Troubleshooting Chart
"
WT-4, "
NVH Troubleshooting Chart
"
WT-4, "
NVH Troubleshooting Chart
"
FA X-4, "
NVH Troubleshooting Chart
"
BR-5, "
NVH Troubleshooting Chart
"
Possible cause and SUSPECTED
PA R T S
Outer/Inner socket ball joint swinging torque
Outer/Inner socket ball joint end play
Steering wheel play
Steering gear pinion rotating torque
Improper steering wheel
Improper installation or looseness of tilt lock lever
Mounting loosenesss
Steering column deformation or damage
Improper installation or looseness of steering column
Steering linkage looseness
WHEEL HUB
SUSPENSION
TIRES
ROAD WHEEL
DRIVE SHAFT
BRAKES
SymptomNoise××× × ××××× ×
Shake××× ××××× ×
Vibration××××× ××× ×
Shimmy××× × ×××× ×
Shudder× × ×××× ×

PS-10
STEERING COLUMN
Revision: June 20062007 Versa
8. Remove bolt of intermediate shaft (upper side), and then remove intermediate shaft from steering column
assembly.
9. Remove steering column assembly mounting nuts, and then remove steering column assembly from vehi-
cle.
10. Remove bolt of intermediate shaft (lower side), and then remove intermediate shaft from vehicle.
11. Remove screws of bracket and EPS control unit, and then remove bracket and EPS control unit from
steering column assembly.
INSPECTION AFTER REMOVAL

Check each part of steering column assembly, EPS control unit and intermediate shaft for damage and .
replace as necessary.

Measure the length “L” as shown, if vehicle has been involved in
a minor collision. Replace steering column assembly (with
motor, reduction gear, sensor) if outside the standard.

Check tilt mechanism for damage or other malfunctions.
Replace steering column assembly (with motor, reduction gear,
sensor) as necessary.

Measure steering column assembly rotating torque using Tool.
Replace steering column assembly (with motor, reduction gear, sensor) if outside the standard.
INSTALLATION
Installation is in the reverse order of removal.

Installation is in the reverse order of removal. For tightening torque, refer to PS-9, "COMPONENT" .

When tightening bolt (intermediate shaft lower side), tighten it by hand first, and make sure there is no
feeling of sticking or galling before final tightening.
CAUTION:
Insert bolt in the proper direction. (Do not insert it from the other side.)

When connecting intermediate shaft upper side (1) and column
shaft, make sure the bolt is securely seated in groove (A) of col-
umn shaft (A) before final tightening.
INSPECTION AFTER INSTALLATION

Rotate steering wheel to check for decentered condition, binding, noise or excessive steering effort.

After installing steering column assembly, perform self-diagnosis with CONSULT-II to ensure correct oper-
ation. Refer to STC-13, "
CONSULT-II Function (EPS)" . Steering column
length “L”Minimum 462.1 mm (18.19 in)
Nominal 464.1 mm (18.27 in)
Maximum 466.1 mm (18.35 in)
Tool number : ST3127S000 (J-25742-1)
Rotating torque : 0 - 2.1 N·m (0 - 0.21 kg-m, 0 - 18 in-lb)
SGIA1293E
SGIA1295E

PS-12
POWER STEERING GEAR
Revision: June 20062007 Versa
POWER STEERING GEARPFP:49001
Removal and InstallationEGS0014Y
COMPONENT
CAUTION:
Spiral cable may be cut if steering wheel turns while separating steering column assembly and steer-
ing gear assembly. Be sure to secure steering wheel using string to avoid turning.
REMOVAL
1. Set vehicle to the straight-ahead position.
2. Remove bolt of intermediate shaft (lower side), and then remove intermediate shaft from steering gear
pinion shaft.
3. Raise vehicle.
4. Remove tires from vehicle with a power tool.
5. Loosen steering outer socket (1) mounting nut.
6. Remove steering outer socket (1) from steering knuckle (2) so
as not to damage ball joint boot (3) using the ball joint remover
(suitable tool).
CAUTION:
Temporarily tighten the nut to prevent damage to threads
and to prevent the ball joint remover (suitable tool) from
suddenly coming off.
7. Remove front suspension member. Refer to FSU-10, "
Removal and Installation" .
8. Remove mounting bolts and nuts of steering gear assembly.
INSTALLATION
Installation is in the reverse order of removal.

For tightening torque, refer to PS-12, "COMPONENT" .

Clean mounting surface on the body side of fire wall seal when installing steering gear assembly.
1. Steering gear assembly 2. Washer 3. Fire wall seal
4. Heat insulator 5. Front suspension member
Refer to GI-8, "
HOW TO USE THIS MANUAL" for the symbols.
SGIA1296E
SGIA1298E

POWER STEERING GEAR
PS-15
C
D
E
F
H
I
J
K
L
MA
B
PS
Revision: June 20062007 Versa

Apply an axial load of 490 N (50 kg-f, 111 lb-f) to ball stud
using a dial gauge. Measure amount of stud movement, and
then make sure that the value is within the specified range.
Replace outer socket and inner socket if the measured value
is outside the standard.
ASSEMBLY
1. Apply recommended grease to teeth part and bush part of rack assembly, if necessary.
2. Apply recommended grease to back of rack assembly, if necessary.
3. Install inner socket to rack assembly. Torque to specified value while holding the flat portion of the rack
next to the inner socket using a suitable tool.
4. Apply recommended grease to inner socket. For application points, refer to PS-13, "
COMPONENT (R24K
TYPE)" .
5. Decide on the neutral position for the rack assembly.
6. Apply recommended grease to around retainer (3), then install
retainer (3), spring (4) and adjusting screw (1) to gear housing
assembly (5).
7. Apply recommended thread locking sealant to the thread (2
turns thread), and then screw in the adjusting screw (1) until it
reaches height “H” from gear housing assembly (5) measured
before disassembling.
8. Tighten lock nut to (2) the specified torque securing it to prevent
adjusting screw (1) from freewheeling condition.
9. Move rack assembly 10 strokes throughout the full stroke so that
the parts can fit with each other.
10. Using Tools A and B, measure rotating torque of pinion assem-
bly. If the measurement is outside of the specified range, read-
just pinion rotating torque. If the measurement is outside of the
specified range for readjust, replace steering gear assembly. Outer socket 0.5 mm (0.020 in) or less
Inner socket 0.2 mm (0.008 in) or less
SGIA0057E
Rack stroke “L” : 65.0 mm (2.559 in)
WGIA0185E
SGIA1300E
Tool numbers A: ST3127S000 (J-25742-1)
B: KV48103400 ( — )
Pinion rotating torque standard
Around neutral position
(within±100°) Average A0.3 - 1.5 N·m (0.03 - 0.15 kg-m,
3 - 13 in-lb)
Maximum variation C 1.86 N·m (0.19 kg-m, 16 in-lb)
MGIA0017E

SERVICE DATA AND SPECIFICATIONS (SDS)
PS-17
C
D
E
F
H
I
J
K
L
MA
B
PS
Revision: June 20062007 Versa
SERVICE DATA AND SPECIFICATIONS (SDS)PFP:00030
Steering WheelEGS00150
Steering AngleEGS00151
Steering ColumnEGS00152
Steering Outer Socket and Inner SocketEGS00153
Steering wheel axial end play 0 mm (0 in)
Steering wheel play 0 - 35 mm (0 - 1.38 in)
Steering wheel turning force Less than 36 N (3.7 kg-f, 8.2 lb-f)
Inner wheel
Degree minute (Decimal degree)Minimum 35° 00′ (35.0°)
Nominal 38° 00′ (38.0°)
Maximum 39° 00′ (39.0°)
Outer wheel
Degree minute (Decimal degree)33° 00′ (33.0°)
Steering column length “L”Minimum 462.1 mm (18.19 in)
Nominal 464.1 mm (18.27 in)
Maximum 466.1 mm (18.35 in)
Steering column assembly rotating torque 0 - 2.1 N·m (0 - 0.21 kg-m, 0 - 18 in-lb)
Tilt operating range20 mm (0.79 in)
SGIA1293E
Steering gear typeR24K
Outer socket ball studSwinging torque 0.3 - 2.9 N·m (0.03 - 0.29 kg-m, 3.0 - 25 in-lb)
Measurement on spring balance
Measuring point: ball stud upper side6.0 - 58 N (0.61 - 5.91 kg-f, 1.35 - 13.03 lb-f)
Axial end play 0.5 mm (0.020 in) or less
Inner socket ball jointSwinging torque 0.5 - 5.0 N·m (0.06 - 0.51 kg-m, 5 - 44 in-lb)

Measurement on spring balance

Measuring point at *mark shown4.3 - 43.5 N (0.44 - 4.44 kg-f, 0.97 - 9.79 lb-f)
Axial end play 0.2 mm (0.008 in) or less
Inner socket length “L”57.8 mm (2.276 in)
SGIA0950E