2006 MERCEDES-BENZ SPRINTER turn signal

TEST ACTION APPLICABILITY
4 Turn the ignition off.
NOTE: Check connectors - Clean/repair as necessary.
Disconnect the Automatic Temperature Control (ATC) C1 harness connector.
Disconnect the Evaporator Temperature Sensor harness connector.
Measure the resistance of the Evaporator Temperature Sensor Signal circuit between
the Automatic Temperature Control (ATC) C1 harness connector and the Evaporator
Temperature Sensor harness connector.
Is the resistance below 5.0 ohms?All
Ye s!Go To 5
No!Repair the Evaporator Temperature Sensor Signal circuit for an
open.
Perform BODY VERIFICATION TEST - VER 1.
5 Turn the ignition off.
NOTE: Check connectors - Clean/repair as necessary.
Disconnect the Automatic Temperature Control (ATC) C1 harness connector.
Disconnect the Evaporator Temperature Sensor harness connector.
Measure the resistance of the Sensor Ground circuit between the Automatic
Temperature Control (ATC) C1 harness connector and the Evaporator Temperature
Sensor harness connector.
Is the resistance below 5.0 ohms?All
Ye s!Replace the Evaporator Temperature Sensor in accordance with
the Service Information.
Perform BODY VERIFICATION TEST - VER 1.
No!Repair the Sensor Ground circuit for an open.
Perform BODY VERIFICATION TEST - VER 1.
157
HEATING & A/C
EVAP TEMP SENSOR HIGH OR OPEN (ACTIVE) ÐContinued

Symptom:
EVAP TEMP SENSOR SHORTED LOW (ACTIVE)
POSSIBLE CAUSES
EVAPORATOR TEMPERATURE SENSOR
EVAP TEMP SENSOR SIGNAL CIRCUIT SHORTED TO GROUND
EVAP TEMP SENSOR SIGNAL CIRCUIT SHORTED TO GROUND CIRCUIT
EVAP TEMP SENSOR SIGNAL CIRCUIT SHORTED TO SENSOR GROUND CIRCUIT
AUTOMATIC TEMPERATURE CONTROL (ATC)
TEST ACTION APPLICABILITY
1 Turn the ignition off.
Disconnect the Evaporator Temperature Sensor harness connector.
Turn the ignition on.
With the DRBIIIt, record and erase Automatic Temperature Control DTCs.
Turn the ignition off, wait 5 seconds, then turn the ignition on.
With the DRBIIIt, read the Automatic Temperature Control DTCs.
Does the DRBIIItdisplay: EVAP TEMP SENSOR HIGH OR OPEN?All
Ye s!Replace the Evaporator Temperature Sensor in accordance with
the Service Information.
Perform BODY VERIFICATION TEST - VER 1.
No!Go To 2
2 Turn the ignition off.
Disconnect the Automatic Temperature Control (ATC) C1 harness connector.
Measure the resistance between ground and the Evaporator Temperature Sensor
Signal circuit.
Is the resistance below 10k ohms?All
Ye s!Repair the Evaporator Temperature Sensor Signal circuit for a
short to ground.
Perform BODY VERIFICATION TEST - VER 1.
No!Go To 3
3 Turn the ignition off.
Disconnect the Automatic Temperature Control (ATC) C1 harness connector.
Measure the resistance between the Evaporator Temperature Sensor Signal circuit
and the Ground circuit.
Is the resistance below 10k ohms?All
Ye s!Repair the Evaporator Temperature Sensor Signal circuit for a
short to the Ground circuit.
Perform BODY VERIFICATION TEST - VER 1.
No!Go To 4
158
HEATING & A/C

TEST ACTION APPLICABILITY
4 Turn the ignition off.
Disconnect the Automatic Temperature Control (ATC) C1 harness connector.
Disconnect the Evaporator Temperature Sensor harness connector.
Measure the resistance between the Evaporator Temperature Sensor Signal circuit
and the Sensor Ground circuit.
Is the resistance below 10k ohms?All
Ye s!Repair the Evaporator Temperature Sensor Signal circuit for a
short to the Sensor Ground circuit.
Perform BODY VERIFICATION TEST - VER 1.
No!Replace the Automatic Temperature Control (ATC) in accordance
with the Service Information.
Perform BODY VERIFICATION TEST - VER 1.
159
HEATING & A/C
EVAP TEMP SENSOR SHORTED LOW (ACTIVE) ÐContinued

Symptom:
AMBIENT TEMP SENSOR OPEN/SHORT TO BATTERY
POSSIBLE CAUSES
AMBIENT TEMPERATURE SENSOR SIGNAL (+) CIRCUIT SHORT TO VOLTAGE
AMBIENT TEMPERATURE SENSOR
AMBIENT TEMPERATURE SENSOR SIGNAL RETURN CIRCUIT OPEN
AMBIENT TEMPERATURE SENSOR SIGNAL (+) CIRCUIT OPEN
INSTRUMENT CLUSTER
TEST ACTION APPLICABILITY
1 Turn the ignition off.
Disconnect the Ambient Temperature Sensor harness connector.
Disconnect the Instrument Cluster C1 harness connector.
Measure the voltage between the Ambient Temperature Sensor Signal (+) circuit and
ground.
Is the voltage above 0.2 volts?All
Ye s!Repair the Ambient Temperature Sensor Signal (+) circuit for a
short to voltage.
Perform BODY VERIFICATION TEST - VER 1.
No!Go To 2
2 Disconnect the Ambient Temperature Sensor harness connector.
Connect a jumper wire between the Ambient Temperature Sensor Signal (+) and
Ambient Temperature Sensor Signal Return circuit.
Turn the ignition on, with the DRBIIIt, read DTCs.
Does the DRBIIItdisplay Ambient Temperature Sensor Short to Ground?All
Ye s!Replace the Ambient Temperature Sensor.
Perform BODY VERIFICATION TEST - VER 1.
No!Go To 3
3 Turn the ignition off.
Disconnect the Ambient Temperature Sensor harness connector.
Disconnect the Instrument Cluster C1 harness connector.
Measure the resistance of the Ambient Temperature Sensor Signal Return circuit
between the Instrument Cluster C1 harness connector and the Ambient Temperature
Sensor harness connector.
Is the resistance above 10 ohms?All
Ye s!Repair the Ambient Temperature Sensor Signal Return circuit for
an open.
Perform BODY VERIFICATION TEST - VER 1.
No!Go To 4
179
INSTRUMENT CLUSTER

TEST ACTION APPLICABILITY
4 Turn the ignition off.
Disconnect the Instrument Cluster C1 harness connector.
Disconnect the Ambient Temperature Sensor harness connector.
Measure the resistance of the Ambient Temperature Sensor Signal (+) circuit
between the Instrument Cluster C1 harness connector and the Ambient Temperature
Sensor harness connector.
Is the resistance above 10 ohms?All
Ye s!Repair the Ambient Temperature Sensor Signal (+) circuit for an
open.
Perform BODY VERIFICATION TEST - VER 1.
No!Replace the Instrument Cluster in accordance with the Service
Information.
Perform BODY VERIFICATION TEST - VER 1.
180
INSTRUMENT CLUSTER
AMBIENT TEMP SENSOR OPEN/SHORT TO BATTERY ÐContinued

Symptom:
AMBIENT TEMP SENSOR SHORT TO GROUND
POSSIBLE CAUSES
AMBIENT TEMPERATURE SENSOR
AMBIENT TEMPERATURE SENSOR SIGNAL (+) CIRCUIT SHORT TO GROUND
AMBIENT TEMPERATURE SENSOR SIGNAL (+) CIRCUIT SHORT TO SENSOR RETURN CIR-
CUIT
INSTRUMENT CLUSTER
TEST ACTION APPLICABILITY
1 Turn the ignition off.
Disconnect the Ambient Temperature Sensor harness connector.
Turn the ignition on. With the DRBIIIt, read DTCs.
Does the DRBIIItdisplay Ambient Temperature Sensor Open/Short to Battery?All
Ye s!Replace the Ambient Temperature Sensor.
Perform BODY VERIFICATION TEST - VER 1.
No!Go To 2
2 Turn the ignition off.
Disconnect the Instrument Cluster C1 harness connector.
Disconnect the Ambient Temperature Sensor harness connector.
Measure the resistance between ground and the Ambient Temperature Sensor Signal
(+) circuit.
Is the resistance below 1000 ohms?All
Ye s!Repair the Ambient Temperature Sensor Signal (+) circuit for a
short to ground.
Perform BODY VERIFICATION TEST - VER 1.
No!Go To 3
3 Turn the ignition off.
Disconnect the Ambient Temperature Sensor harness connector.
Disconnect the Instrument Cluster C1 harness connector.
Measure the resistance between the Ambient Temperature Sensor Signal (+) circuit
and Ambient Temperature Sensor Signal Return circuit.
Is the resistance below 1000 ohms?All
Ye s!Repair the Ambient Temperature Sensor Signal (+) circuit for a
short to the Sensor Return circuit.
Perform BODY VERIFICATION TEST - VER 1.
No!Replace the Instrument Cluster in accordance with the Service
Information.
Perform BODY VERIFICATION TEST - VER 1.
181
INSTRUMENT CLUSTER

Symptom:
FUEL LEVEL SENSOR OPEN/SHORT TO BATTERY
POSSIBLE CAUSES
FUEL LEVEL SENSOR
FUEL LEVEL SENSOR SIGNAL (+) CIRCUIT SHORT TO VOLTAGE
FUEL LEVEL SENSOR SIGNAL RETURN CIRCUIT OPEN
FUEL LEVEL SENSOR SIGNAL (+) CIRCUIT OPEN
INSTRUMENT CLUSTER
TEST ACTION APPLICABILITY
1 Turn the ignition off.
Disconnect the Fuel Pump Module harness connector.
Disconnect the Instrument Cluster C1 harness connector.
Turn the ignition on.
Measure the voltage between Fuel Level Sensor Signal (+) circuit and ground.
Is the voltage above 0.2 volts?All
Ye s!Repair the Fuel Level Sensor Signal (+) circuit for a short to
voltage.
Perform BODY VERIFICATION TEST - VER 1.
No!Go To 2
2 Turn the ignition off.
Reconnect the Instrument Cluster C1 harness connector.
Disconnect the Fuel Pump Module harness connector.
Connect a jumper wire between the Fuel Level Sensor Signal (+) and the Fuel Level
Sensor Signal Return circuit.
Turn the ignition on.
With the DRBIIIt, read DTCs.
Does the DRBIIItdisplay Fuel Level Sensor Open/Short to Battery?All
Ye s!Go To 3
No!Replace the Fuel Level Sensor in accordance with the Service
Information.
Perform BODY VERIFICATION TEST - VER 1.
3 Turn the ignition off.
Disconnect the Fuel Pump Module harness connector.
Disconnect the Instrument Cluster C1 harness connector.
Measure the resistance of the Fuel Level Sensor Signal Return circuit between the
Fuel Pump Module harness connector and the Instrument Cluster harness connector.
Is the resistance above 10 ohms?All
Ye s!Repair the Fuel Level Sensor Signal Return circuit for an open.
Perform BODY VERIFICATION TEST - VER 1.
No!Go To 4
182
INSTRUMENT CLUSTER

TEST ACTION APPLICABILITY
4 Turn the ignition off.
Disconnect the Fuel Pump Module harness connector.
Disconnect the Instrument Cluster C1 harness connector.
Measure the resistance of the Fuel Level Sensor Signal (+) circuit between the Fuel
Pump Module harness connector and the Instrument Cluster harness connector.
Is the resistance above 10 ohms?All
Ye s!Repair the Fuel Level Sensor Signal (+) circuit for an open.
Perform BODY VERIFICATION TEST - VER 1.
No!Replace the Instrument Cluster in accordance with the Service
Information.
Perform BODY VERIFICATION TEST - VER 1.
183
INSTRUMENT CLUSTER
FUEL LEVEL SENSOR OPEN/SHORT TO BATTERY ÐContinued