2006 LEXUS RX330 ECO mode

GAUGES, METERS AND SERVICE REMINDER INDICATORS
73
ODOMETER AND TRIP METER
Vehicles with dynamic laser cruise control
Vehicles without dynamic laser cruise control This
meter displays the odometer and two trip meters. To
change the mode indication, push the “ODO/TRIP” button
briefly. Each time you push the button, the mode changes
in order from the odometer to trip meter A to trip meter B,
then back to the odometer, etc.
The odometer records the total distance the vehicle has
been driven. The twin trip meter records two different
distances independently.
For example, you can use one meter to calculate the fuel
economy and the other to measure the distance on each trip.
To set the A trip meter to zero, display the A meter reading,
push the button and hold it. The same applies for the B trip
meter.
The data of trip meters will be cancelled if the electrical power
source is disconnected.

GAUGES, METERS AND SERVICE REMINDER INDICATORS
83
(l) “VSC” Warning Light
This light warns that there is a problem somewhere in the
vehicle stability control system or traction control system.
The light will come on when the ignition key is turned to the
“ON” position and will go off after a few seconds.
If the light comes on while driving, the vehicle stability control
system and traction control system do not work. However, as
conventional braking operates when applied, there is no
problem to continue your driving.
In the following cases, contact your Lexus dealer:
 The warning light does not come on after the ignition key is
turned to the “ON” position.
 The warning light remains on after the ignition key is turned
to the “ON” position.
 The warning light comes on while driving.
Tw o −wheel drive models only — The “TRAC OFF” indicator
light will come on when the “VSC” warning light comes on even
if the “TRAC OFF” switch is not pushed.
(m) Automatic Transmission Fluid Temperature Warning Light
(fourwheel drive models only)
This light warns that the automatic transmission fluid
temperature is too high.
If this light comes on while you are driving, slow down and pull
off the road. Stop the vehicle at a safe place and put the
selector lever in “P” and leave the engine idling until the light
goes off. If the light goes off, you can start the vehicle again.
If the light does not go off, call a Lexus dealer or qualified repair
shop for assistance.
NOTICE
Continued driving with the warning light on may
damage the automatic transmission.
(n) Low Washer Fluid Warning Light
This light comes on when the fluid level in the tank becomes
nearly empty. Fill the tank as soon as possible.

GAUGES, METERS AND SERVICE REMINDER INDICATORS
86
or or
or
13RY032
13RY033 13RY030
13RY029 13RY035
The following service reminder indicators go off after a few
seconds.
 Height control indicator lights
 Height control off indicator light
 Easy access mode indicator light
 Dynamic laser cruise control master warning light
or

13RY032
13RY033 13RY030 13RY029
13RY035

INTERIOR EQUIPMENT
98
1Foot lights (on some models)
2Meter ring light
3Ignition switch light
4Center console spot lights
5Front interior light (with the “DOOR” position)
6Inside door handle lights (on some models)
7Rear interior light (with the “DOOR” position)
8Scuff plate lights (on some models)
All of the lights except the center console spot lights and
meter ring light will come on when any of the side doors
are opened.* After all the doors are closed, the lights
remain on for about 15 seconds before fading out.** NOTE:
* The operating condition can be changed.
** The duration of lighting can be changed.
Ask your Lexus dealer for details. However, in
the following cases, the lights go out immediately:
 All of the lights except the center console spot lights and
meter ring light — All the side doors and back door are
locked.
 Ignition switch light, front interior light, rear interior light and
scuff plate lights — All the side doors are closed and the
ignition key is in the “ACC” or “ON” position.
When any of the side doors is unlocked, all of the lights except
the center console spot light and meter ring light will come on
and remain on for about 15 seconds before fading out.
To prevent the battery from being discharged, all of the lights
will automatically turn off when the ignition key is removed and
the door is left opened for about 20 minutes.
Ignition switch light, front interior light, rear interior light
and scuff plate lights
The ignition switch light, front interior light, rear interior light and
scuff plate lights also come on and remain on for about 15
seconds before fading out when the ignition switch is turned to
the “LOCK” position.

STEERING WHEEL AND MIRRORS
233
INSIDE REAR VIEW MIRROR
Adjust the mirror so that you can just see the rear of your
vehicle in the mirror. Pushing the “MIRROR” switch changes the mode
between AUTO and DAY.
The indicator comes on when the AUTO mode is selected.
DAY mode: The mirror surface is normal.
AUTO mode: If the mirror detects light from the headlights
of the vehicle behind you, the mirror surface darkens
slightly to reduce the reflected light.
When
the inside rear view mirror surface changes, the outside
rear view mirror surfaces will also become darker.
When the ignition key is inserted and turned on, the inside rear
view mirror always turns on in the AUTO mode.
When the outside air temperature is low, it may take a little
longer for the mirror to darken in response to the detection of
headlights.

AIR CONDITIONING
243
The automatic air conditioning automatically maintains
the set temperature.
In the automatic operation mode, the air conditioning selects
the most suitable fan speed, air flow, air intake and on−
off the
air conditioning according to the temperature.
The ignition key must be in the “ON” position.
NOTICE
To prevent the battery from being discharged, do not
leave the air conditioning on longer than necessary
when the engine is not running.
1Driver side temperature display (in degrees
Fahrenheit or Centigrade)
2Air flow display
3Fan speed display
4Passenger side temperature display (in degrees
Fahrenheit or Centigrade)
5“TEMP” (driver side temperature control) button
(At the independent mode that display shows
“DUAL”; mainly for driver and secondarily for
front passenger)
(At the linked mode that display does not show
“DUAL”; for driver)
6“AUTO” button
7“OFF” button
8Air intake control button
9“A/C” button
10Fan speed control button
11“MODE”(air flow control) button
12“DUAL” (temperature setting mode change) button
13Windshield air flow button
14“PASSENGER TEMP” (passenger side temperature
control) button
(Only for the independent mode that display
shows “DUAL”; mainly for front passenger and
secondarily for driver)

AIR CONDITIONING
246
INFORMATION
This automatic control has additional function as
described below, when the “AUTO” button is pushed.
The fan speed is stopped for a little while until warm
air preparation, when outside temperature is cold like
a winter season in the “Floor”, “Bilevel” or
“Floor/Windshield” air flow mode. If quick removal
for exterior frost, fog and inside fog on the windshield
is desired, use the high fan speed setting after the
“Windshield” air flow mode has been selected.
The fan speed is stopped few seconds until cool air
preparation, when outside temperature is hot like a
summer season in the “Panel” or “Bilevel” air flow
mode.
 The internal circulation may be applied for maximum
cooling in the automatic operation mode, when
outside temperature is hot like a summer season.
If fresh outside air is desired into the vehicle, push
the air intake control button to select the OUTSIDE
AIR mode.
The “Floor/Windshield” air flow mode may be applied
automatically, if the outside temperature is lowered
down to below 0C (32F).
This is not malfunction. The “Floor/Windshield” air
flow mode turns on the defogging and defrosting
function with the purpose of cleaning your front view
for safe driving.
If the “Floor” air flow mode is desired with the main
purpose of heating, “Floor” air flow mode can be
selected manually by pushing the “MODE” (air flow
control) button.

AIR CONDITIONING
251
If manual switching of air intake is desired —
The air intake control button is used to switch the air intake
between the OUTSIDE AIR mode and RECIRCULATED AIR
mode.
With the button in the OUTSIDE AIR mode, the indicator light
will turn off and the system will take fresh outside air into the
vehicle.
If quick circulation of cooled air is desired, push the air intake
control
button for RECIRCULATED AIR. The indicator light will
come on.
For normal use, it is best to keep the air intake control button
set to the OUTSIDE AIR mode. If recirculated air is used during
heating, the windows will fog up more easily. To prevent fogging up of the windshield, the air intake mode
may change automatically to the OUTSIDE AIR mode
depending on the condition of the air conditioning system.
For example, when the ambient temperature is low, the air
intake mode may change automatically to the OUTSIDE AIR
mode. This is not a malfunction.
When the air conditioning is ON, if the engine coolant
temperature becomes extremely high, the RECIRCULATED
AIR mode is automatically selected. This is not a malfunction.
When
the engine coolant temperature is lowered, the previous
mode resumes.
If manual onoff of the air conditioning is desired —
Push the “A/C” button to turn the air conditioning on and push
it again to turn the air conditioning off.
The air conditioning does not work if the outside temperature
is lowered down to around 0 C (32F).
If the system is used for ventilation, heating in dry weather or
removing frost or exterior fog on the windshield, turn the air
conditioning off once it is no longer required. This will improve
fuel economy. The air conditioning can be used for year− round
automatic temperature control including cooling and
dehumidifying operation.
If the air conditioning compressor does not operate, the
indicator of the “A/C” button will blink. If the indicator of the
“A/C” button blinks even when the “A/C” button is pushed
again, have the compressor checked by your nearest Lexus
dealer.