2006 LEXUS LX470 display

AIR CONDITIONING
203
1 Temperature control knob
2 Automatic control button
3 Temperature display (in degrees Fahrenheit or
Centigrade)
4 Fan speed display
5 Air flow display
6 Air conditioning onoff button
7 Air flow control button
8 Windshield air flow button
9 Fan speed control button
10 Air intake control button
11 OFF button

AIR CONDITIONING
205
(a) Climate control
SETTING OPERATION automatic control
20X019d
1. Push the “AUTO” button.
Air flow quantity, switching of the diffusers, on−off of the air
conditioning, and switching of the air intake between
RECIRCULATED AIR and OUTSIDE AIR are automatically
adjusted. The operation status is shown by each indicator.
When one of the manual control buttons is depressed while
operating in automatic mode, the mode relevant to the
depressed button is set. Other conditions continue to be
adjusted automatically.
It is recommended that you close the lower vent. For details
about this, see page 212.
Push the “OFF” button to turn the air conditioning off.
20X020d
2. Turn the “TEMP” knob until the desired temperature is
displayed.
The “TEMP” knob is used to set the desired passenger
compartment temperature. The temperature of air delivered
to the passenger compartment will be controlled automatically
according to the setting. The figures on the panel indicate
degrees Fahrenheit or Centigrade.

AIR CONDITIONING
206SETTING OPERATION manual control
When one of the manual control buttons is depressed
while operating in automatic mode, the mode relevant to
the depressed button is set. Other conditions continue to
be adjusted automatically.
If manual air flow selection is desired
20X021a
The outlets from which air is delivered can be selected
manually by pressing the button. The function of each mode
is as follows:
1
Panel − Air flows mainly from the instrument panel vents.
2
Bilevel − Air flows from both the floor vents and the
instrument panel vents.
3 Floor − Air flows mainly from the floor vents.
It is recommended that you close the lower vent. For details
about this, see page 212.
4 Floor/Windshield − Air flows mainly from the floor vents
and windshield vents.
It is recommended that you close the lower vent. For details
about this, see page 212.
If quick heating or cooling is desired
Turn the “TEMP” knob until “MAX. HOT” or “MAX. COLD”
appears on the display.
If manual fan speed control is desired
21x600
 1 Fan speed at low 2Fan speed at high
The fan speed can be set to your desired speed by pushing the
appropriate side of fan speed control button. The higher the
fan speed is, the more air is delivered. Pushing the “OFF”
button turns off the fan.
To remove exterior windshield frost, use the high speed
setting.

AIR CONDITIONING
207
If manual switching of air intake is desired
20X023a
Each time you push the air intake control button, the mode
changes in order from the RECIRCULATED AIR mode to
AUTOMATIC mode to OUTSIDE AIR mode, then back to the
RECIRCULATED
AIR mode. Each indicator light shows which
mode is now selected.
1 RECIRCULATED mode If quick circulation of cooled air
is desired, select this mode.
2 EXHAUST GAS AUTOMATIC mode If the outside air
contains harmful substances like exhaust gas (i.e., when
the vehicle running just in front of your vehicle accelerates
rapidly), the system changes automatically from the
OUTSIDE AIR mode (with indicators
2
and 3 on) to
the RECIRCULATED mode (with indicators 1
and 2
on).
3 OUTSIDE AIR mode The system will take fresh outside
air into the vehicle. Turning off the air conditioning manually will cancel the
EXHAUST
GAS AUTOMATIC mode. If you select the “AUTO”
mode during fan operating, the air conditioning turns on and
the EXHAUST GAS AUTOMATIC mode will operate.
For normal use, it is best to keep the air intake control button
set to OUTSIDE AIR mode. If recirculated air is used during
heating, the windows will fog up more easily.
In the following cases, the RECIRCULATED mode may
change to the OUTSIDE AIR mode automatically to prevent
interior fog.
 When the outside temperature becomes lower than 4 C
(39 F).
 When the air conditioning compressor malfunctions.
 When the air conditioning cooler refrigerant decreases.
To change the sensitivity of the sensor switching between
the RECIRCULA TED and OUTSIDE AIR in the AUTOMATIC
mode, push the air intake control button until the “AUTO”
indicator light flashes. The display changes as illustrated
below.
The sensitivity of the sensor can be adjusted only while the
vehicle has stopped.

AIR CONDITIONING
208
20X062d
When you turn the “TEMP” knob, the sensitivity changes from
“+3” down to “−3”. If you do not operate any button for a few
seconds or if you push a button other than the air intake control
button and temperature control knob, the previous display
returns.
If manual onoff of the air conditioning is desired
Push the “A/C” button to turn the air conditioning on and push
it again to turn the air conditioning off. If you turn off the air
conditioning manually, the EXHAUST GAS AUTOMATIC
mode will be cancelled.
If the outside temperature is lowered down to around 0 C
(32 F), the air conditioning will turn off automatically. At this
time, the indicator on the A/C button is off and the EXHAUST
GAS AUTOMATIC indicator light remains on. However, the
EXHAUST GAS AUTOMA TIC mode does not operate. When
the air conditioning turns on as with the raised temperature, the
EXHAUST GAS AUTOMATIC mode resumes. If the system is used for ventilation, heating in dry weather or
removing frost or exterior fog on the windshield, turn the air
conditioning off
once it is no longer required. This will improve
fuel economy. The air conditioning can be used for year −round
automatic temperature control including cooling and
dehumidifying operation.
If the air conditioning compressor does not operate, the
indicator of the “A/C” button will blink. If the indicator of the
“A/C” button blinks even when the “A/C” button is pushed
again, have the compressor checked by your nearest Lexus
dealer.

AUDIO
218
AUDIO SYSTEM
Quick reference for your audio system
22X611a
You can adjust the brightness of the display. See “Instrument panel light control” on page 66 for details.

AUDIO
219
1Stopping and ejecting a CD
(See page 239 for details.)
2CD slot
(See page 238 for details.)
3Display of functions in TAPE mode
RPT: Automatic repeat
(See page 236 for details.)
:DOLBY NR
(See page 235 for details.)
:
Side change
(See page 236 for details.)
 :Rewinding or Fast forwarding
 :(See page 236 for details.)
3
Display of functions in CD mode
RAND: Random access
(See page 242 for details.)
RPT: Automatic repeat
(See page 241 for details.)
:CD selection
(See page 240 for details.)
 :Reversing or Fast forwarding
 :(See page 241 for details.)
4
Scan button
(See page 226, 231 or 240 for details.)
5Load button
(See page 238 for details.)
6TEXT button
(See page 227, 232 or 242 for details.)
7AUDIO·TUNE knob
(See page 221 or 225 for details.)
8 Traffic announcement button
(See page 227 for details.)
9 Program type button
(See page 226 for details.)
10 Mode selectors
(See page 220 for details.)
11 AM·FM mode: Seek tuning
(See page 224 or 225 for details.)
SAT mode: Manual tuning
(See page 230 for details.)
TAPE or CD Direct access to a desired program
mode: (See page 237 or 241 for details.)
12Cassette tape slot
(See page 235 for details.)
13Stopping and ejecting a cassette tape
(See page 235 for details.)
14Turning the system on and adjusting the volume
(See page 220 for details.)
15Function buttons
1 6: Station selector buttons
(See page 225 for details.)

AUDIO
221
21X553
In the “TAPE” or “CD” mode, the applicable functions are
shown in the lowest part of the display. Push the switch
just below to turn on each function.
(b) Tone and balance
How good an audio program sounds to you is largely
determined by the mix of the treble, mid −range, and bass
levels. In fact, different kinds of music and vocal programs
usually sound better with different mixes of treble, mid− range,
and bass.
A good balance of the left and right stereo channels and of the
front and rear sound levels is also important.
Keep in mind that if you are listening to a stereo recording or
broadcast, changing the right/left balance will increase the
volume of one group of sounds while decreasing the volume
of another.
22X612
Each time you push the “AUDIOTUNE” knob, the display
changes as in the following. To adjust the tone and
balance or turn on or off the automatic sound levelizer,
turn the knob.
BAS: Adjusts low− pitched tones.
MID: Adjusts mid− pitched tones.
TRE: Adjusts high− pitched tones.
FAD: Adjusts the sound balance between the front and rear
speakers.
BAL: Adjusts the sound balance between the right and left
speakers.
ASL: Turns on or off the automatic sound levelizer.
Automatic Sound Levelizer (ASL): When the audio sound
becomes difficult to be heard due to road noise, wind noise,
etc. during driving, the system adjusts to the optimum volume
and tone quality according to the noise level. While the
Automatic Sound Levelizer (ASL) is on, “ASL” appears on the
display.