2006 INFINITI QX56 rack

OVERHAULAT-257
DE
F
G H
I
J
K L
M A
B
AT
Revision: November 2009 2006 QX56
7. Pawl shaft8. Bracket9. Self-sealing bolt
10. Seal ring 11. Needle bearing12. Gasket
13. Revolution sensor 14. Parking gear15. Output shaft
16. Bearing race 17. Needle bearing18. Manual plate
19. Parking rod 20. Manual shaft oil seal21. Manual shaft
22. O-ring 23. Band servo anchor end pin 24. Detent spring
25. Spacer 26. Seal rings27. Return spring
28. O-ring 29. Servo assembly30. Snap ring
31. Snap ring 32. Sub-harness33. Control valve with TCM
34. Bracket 35. A/T fluid temperature sensor 2 36. Oil pan
37. Magnets 38. Drain plug39. Drain plug gasket
40. Oil pan bolt 41. Oil pan gasket42. Terminal cord assembly
43. O-ring 44. Retaining pin45. Transmission case

DISASSEMBLYAT-267
DE
F
G H
I
J
K L
M A
B
AT
Revision: November 2009 2006 QX56
14. Loosen lock nut and remove band servo anchor end pin from
transmission case.
15. Remove brake band from transmission case.

To prevent brake linings from cracking or peeling, do not
stretch the flexible band unnecessarily. When removing
the brake band, always secure it with a clip as shown.
Leave the clip in position after removing the brake band.

Check brake band facing for damage, cracks, wear or
burns.
16. Remove mid carrier assembly and rear carrier assembly as a unit.
SCIA5016E
SCIA5345E
SAT655
SCIA5344E

DISASSEMBLYAT-271
DE
F
G H
I
J
K L
M A
B
AT
Revision: November 2009 2006 QX56
32. Straighten terminal clips to free revolution sensor harness.
33. Remove bolts A, B and C from control valve with TCM.
34. Remove control valve with TCM from transmission case.
CAUTION:
When removing, be careful with transmission assembly ter-
minal connector and the manual valve notch and manual
plate height. Remove it vertically.
35. Remove A/T fluid temperature sensor 2 with bracket from con- trol valve with TCM.
36. Remove bracket from A/T fluid temperature sensor 2.
SCIA7023E
Bolt symbol Length mm (in) Number of bolts
A 42 (1.65) 5
B 55 (2.17) 6
C 40 (1.57) 1
SCIA5025E
SCIA5308E
SCIA5301E
SCIA5264E

DISASSEMBLYAT-273
DE
F
G H
I
J
K L
M A
B
AT
Revision: November 2009 2006 QX56
a.2WD models

Self-sealing bolts (2)
i. Remove bolts for rear extension assembly and transmission case.
ii. Remove brackets (1).
iii. Tap rear extension assembly using suitable tool.
iv. Remove rear extension assembly with needle bearing from transmission case.
b. 4WD models

Self-sealing bolts (2)
i. Remove bolts for adapter case assembly and transmission case.
ii. Remove brackets (1).
WCIA0562E
SCIA5028E
SCIA5029E
WCIA0563E

AT-288
REPAIR FOR COMPONENT PARTS
Revision: November 20092006 QX56
4. Disassemble input clutch assembly.
a. Remove O-ring and seal rings from input clutch assembly.
b. Remove needle bearing from input clutch assembly.
c. Remove snap ring from input clutch drum using suitable tool.
d. Remove drive plates, driven plates and retaining plate from input
clutch drum.
INSPECTION
Front Carrier Snap Ring

Check for deformation, fatigue or damage.
CAUTION:
If necessary, replace the snap ring.
Input Clutch Snap Ring

Check for deformation, fatigue or damage.
CAUTION:
If necessary, replace the input clutch assembly.
Input Clutch Drum

Check for deformation, fatigue or damage or burns.
CAUTION:
If necessary, replace the input clutch assembly.
Input Clutch Drive Plates

Check facing for burns, cracks or damage.
CAUTION:
If necessary, replace the input clutch assembly.
Input Clutch Retaining Plate and Driven Plates

Check facing for burns, cracks or damage.
SCIA5235E
SCIA2853E
SCIA2864E

AT-296
REPAIR FOR COMPONENT PARTS
Revision: November 20092006 QX56
High and Low Reverse ClutchECS00EOG
COMPONENTS
DISASSEMBLY
1. Remove bearing race from high and low reverse clutch drum.
2. Remove snap ring from high and low reverse clutch drum using
suitable tool.
3. Remove drive plates, driven plates and retaining plate from high and low reverse clutch drum.
INSPECTION

Check the following, and replace high and low reverse clutch assembly if necessary.
High and Low Reverse Clutch Snap Ring

Check for deformation, fatigue or damage.
High and Low Reverse Clutch Drive Plates

Check facing for burns, cracks or damage.
1. High and low reverse clutch drum 2. Driven plate 3. Retaining plate
4. Snap ring 5. Drive plate 6. Bearing race
SCIA5239E
SCIA5240E
SCIA2868E

REPAIR FOR COMPONENT PARTSAT-297
DE
F
G H
I
J
K L
M A
B
AT
Revision: November 2009 2006 QX56
High and Low Reverse Clutch Retaining Plate and Driven Plates

Check facing for burns, cracks or damage.
ASSEMBLY
1. Install drive plates, driven plates and retaining plate in high and
low reverse clutch drum.
CAUTION:
Take care with the order of plates.
2. Install snap ring in high and low reverse clutch drum using suit- able tool.
3. Install bearing race to high and low reverse clutch drum. CAUTION:
Apply petroleum jelly to bearing race.
SCIA5241E
SCIA2868E
SCIA5240E

AT-298
REPAIR FOR COMPONENT PARTS
Revision: November 20092006 QX56
Direct ClutchECS00EOH
COMPONENTS
DISASSEMBLY
1. Remove snap rings from direct clutch drum using suitable tool.
2. Remove drive plates, driven plates and retaining plate from
direct clutch drum.
INSPECTION

Check the following, and replace direct clutch assembly if necessary.
Direct Clutch Snap Rings

Check for deformation, fatigue or damage.
Direct Clutch Drive Plates

Check facing for burns, cracks or damage.
Direct Clutch Retaining Plate and Driven Plates

Check facing for burns, cracks or damage.
1. Direct clutch drum 2. Driven plate 3. Retaining plate
4. Snap ring 5. Drive plate
SCIA5242E
SCIA2868E