2006 INFINITI QX56 relay

INDEX FOR DTCAT-5
DE
F
G H
I
J
K L
M A
B
AT
Revision: November 2009 2006 QX56
INDEX FOR DTCPFP:00024
Alphabetical Index ECS00CDH
NOTE:
If DTC U1000 is displayed with other DTC, first perform the trouble diagnosis for DTC U1000. Refer to
AT- 9 6 , "
DTC U1000 CAN COMMUNICATION LINE" .
*1: These numbers are prescribed by SAE J2012.
*2: These malfunctions cannot be displayed MIL if another malfunction is assigned to MIL.Items
(CONSULT- II screen terms) DTC
Reference page
OBD- II Except OBD- II
CONSULT- II GST (*1) CONSULT- II only “ A/T”
A/T 1ST E/BRAKING —P1731AT- 1 3 7
ATF PRES SW 1/CIRC —P1841AT- 1 5 9
ATF PRES SW 3/CIRC —P1843AT- 1 6 1
ATF PRES SW 5/CIRC —P1845AT- 1 6 3
ATF PRES SW 6/CIRC —P1846AT- 1 6 5
A/T INTERLOCK P1730P1730AT- 1 3 4
A/T TCC S/V FNCTN P0744 P0744 AT- 1 2 0
ATF TEMP SEN/CIRC P0710P1710AT- 1 2 7
CAN COMM CIRCUIT U1000U1000AT- 9 6
D/C SOLENOID/CIRC P1762P1762AT- 1 4 7
D/C SOLENOID FNCTN P1764 (*2 )P1764 AT- 1 4 9
ENGINE SPEED SIG —P0725AT- 11 6
FR/B SOLENOID/CIRC P1757P1757AT- 1 4 3
FR/B SOLENOID FNCT P1759 P1759 AT- 1 4 5
HLR/C SOL/CIRC P1767P1767AT- 1 5 1
HLR/C SOL FNCTN P1769 (*2 ) P1769 AT- 1 5 3
I/C SOLENOID/CIRC P1752P1752AT- 1 3 9
I/C SOLENOID FNCTN P1754 (*2 ) P1754 AT- 1 4 1
L/PRESS SOL/CIRC P0745P0745AT- 1 2 2
LC/B SOLENOID/CIRC P1772P1772AT- 1 5 5
LC/B SOLENOID FNCT P1774 P1774 AT- 1 5 7
PNP SW/CIRC P0705P0705AT- 1 0 5
STARTER RELAY/CIRC —P0615AT- 1 0 0
TCC SOLENOID/CIRC P0740P0740AT- 11 8
TCM P0700P0700AT- 1 0 4
TP SEN/CIRC A/T —P1705AT- 1 2 4
TURBINE REV S/CIRC P0717P0717AT- 1 0 9
VEH SPD SE/CIR·MTR —P1721AT- 1 3 2
VEH SPD SEN/CIR AT P0720P0720AT- 111

AT-6
INDEX FOR DTC
Revision: November 20092006 QX56
DTC No. Index ECS00CDI
NOTE:
If DTC U1000 is displayed with other DTC, first perform the trouble diagnosis for DTC U1000. Refer to
AT- 9 6 , "
DTC U1000 CAN COMMUNICATION LINE" .
*1: These numbers are prescribed by SAE J2012.
*2: These malfunctions cannot be displayed MIL if another malfunction is assigned to MIL.DTC
Items
(CONSULT- II screen terms) Reference page
OBD- II
Except OBD- II
CONSULT- II GST (*1) C O N S U LT- I I
only “A/T ”
— P0615 STARTER RELAY/CIRC AT- 1 0 0
P0700P0700 TCM AT- 1 0 4
P0705P0705 PNP SW/CIRC AT- 1 0 5
P0710P1710 ATF TEMP SEN/CIRC AT- 1 2 7
P0717P0717 TURBINE REV S/CIRC AT- 1 0 9
P0720P0720 VEH SPD SEN/CIR AT AT- 111
—P0725 ENGINE SPEED SIG AT- 11 6
P0740P0740 TCC SOLENOID/CIRC AT- 11 8
P0744 P0744 A/T TCC S/V FNCTN AT- 1 2 0
P0745P0745 L/PRESS SOL/CIRC AT- 1 2 2
—P1705 TP SEN/CIRC A/T AT- 1 2 4
—P1721 VEH SPD SE/CIR· MTR AT- 1 3 2
P1730P1730 A/T INTERLOCK AT- 1 3 4
— P1731 A/T 1ST E/BRAKING AT- 1 3 7
P1752P1752 I/C SOLENOID/CIRC AT- 1 3 9
P1754 (*2 ) P1754 I/C SOLENOID FNCTN AT- 1 4 1
P1757P1757 FR/B SOLENOID/CIRC AT- 1 4 3
P1759 (*2 ) P1759 FR/B SOLENOID FNCT AT- 1 4 5
P1762P1762 D/C SOLENOID/CIRC AT- 1 4 7
P1764 (*2 )P1764 D/C SOLENOID FNCTN AT- 1 4 9
P1767P1767 HLR/C SOL/CIRC AT- 1 5 1
P1769 P1769 HLR/C SOL FNCTN AT- 1 5 3
P1772P1772 LC/B SOLENOID/CIRC AT- 1 5 5
P1774 P1774 LC/B SOLENOID FNCT AT- 1 5 7
—P1841 ATF PRES SW 1/CIRC AT- 1 5 9
—P1843 ATF PRES SW 3/CIRC AT- 1 6 1
—P1845 ATF PRES SW 5/CIRC AT- 1 6 3
—P1846 ATF PRES SW 6/CIRC AT- 1 6 5
U1000U1000 CAN COMM CIRCUIT AT- 9 6

AT-30
A/T CONTROL SYSTEM
Revision: November 20092006 QX56
TCM FunctionECS00CDW
The function of the TCM is to:

Receive input signals sent from various switches and sensors.

Determine required line pressure, shifting point, lock-up operation, and engine brake operation.

Send required output signals to the respective solenoids.
CONTROL SYSTEM OUTLINE
The automatic transmission senses vehicle operating conditions through various sensors or signals. It always
controls the optimum shift position and reduces shifting and lock-up shocks.
CONTROL SYSTEM DIAGRAM
SENSORS (or SIGNALS)

TCM

ACTUATORS
PNP switch
Accelerator pedal position sensor
Closed throttle position signal
Wide open throttle position signal
Engine speed signal
A/T fluid temperature sensor
Revolution sensor
Vehicle speed signal
Stop lamp switch signal
Turbine revolution sensor
1st position switch signal
4th position switch signal
ATF pressure switch signal
Tow mode switch signal Shift control
Line pressure control
Lock-up control
Engine brake control
Timing control
Fail-safe control
Self-diagnosis
CONSULT-II communication line
Duet-EA control
CAN system
Input clutch solenoid valve
Direct clutch solenoid valve
Front brake solenoid valve
High and low reverse clutch
solenoid valve
Low coast brake solenoid valve
Torque converter clutch solenoid
valve
Line pressure solenoid valve
A/T CHECK indicator lamp
Starter relay
Back-up lamp relay
SCIA5624E

AT-42
TROUBLE DIAGNOSIS
Revision: November 20092006 QX56
TROUBLE DIAGNOSISPFP:00004
DTC Inspection Priority ChartECS00CE9
If some DTCs are displayed at the same time, perform inspections one by one based on the following priority
chart.
NOTE:
If DTC U1000 is displayed with other DTCs, first perform the trouble diagnosis for DTC U1000. Refer to
AT- 9 6
.
Fail-SafeECS00CEA
The TCM has an electrical fail-safe mode. This mode makes it possible to operate even if there is an error in a
main electronic control input/output signal circuit. In fail-safe mode the transmission is fixed in 2nd, 4th or 5th
(depending on the breakdown position), so the customer should feel “slipping” or “poor acceleration ”.
Even when the electronic circuits are normal, under special conditions (for example, when slamming on the
brake with the wheels spinning drastically and stopping the tire rotation), the transmission can go into fail-safe
mode. If this happens, switch “OFF ” the ignition switch for 10 seconds, then switch it “ON” again to return to
the normal shift pattern. Therefore, the customer's vehicle has returned to normal, so handle according to the
“diagnostics flow ” (Refer to AT- 4 5 , "
WORK FLOW" ).
FAIL-SAFE FUNCTION
If any malfunction occurs in a sensor or solenoid, this function controls the A/T to make driving possible.
Vehicle Speed Sensor

Signals are input from two systems - from vehicle speed sensor A/T (revolution sensor) installed on the
transmission and from combination meter so normal driving is possible even if there is a malfunction in
one of the systems. And if vehicle speed sensor A/T (revolution sensor) has unusual cases, 5th gear is
prohibited.
Accelerator Pedal Position Sensor

If there is a malfunction in one of the systems, the accelerator opening angle is controlled by ECM accord-
ing to a pre-determined accelerator angle to make driving possible. And if there are malfunctions in tow
systems, the engine speed is fixed by ECM to a pre-determined engine speed to make driving possible.
Throttle Position Sensor

If there is a malfunction in one of the systems, the accelerator opening angle is controlled by ECM accord-
ing to a pre-determined accelerator angle to make driving possible. And if there are malfunctions in tow
systems, the accelerator opening angle is controlled by the idle signal sent from the ECM which is based
on input indicating either idle condition or off-idle condition (pre-determined accelerator opening) in order
to make driving possible.
PNP Switch

In the unlikely event that a malfunction signal enters the TCM, the position indicator is switched “OFF”, the
starter relay is switched “OFF ” (starter starting is disabled), the back-up lamp relay switched “OFF” (back-
up lamp is OFF) and the position is fixed to the “D” range to make driving possible.
Starter Relay

The starter relay is switched “OFF”. (Starter starting is disabled.)
Priority Detected items (DTC)
1 U1000 CAN communication line
2 Except above

TROUBLE DIAGNOSISAT-83
DE
F
G H
I
J
K L
M A
B
AT
Revision: November 2009 2006 QX56
TCM Input/Output Signal Reference ValuesECS00CEO
A/T ASSEMBLY HARNESS CONNECTOR TERMINAL LAYOUT
TCM INSPECTION TABLE
Data are reference value and are measured between each terminal and ground.
SCIA1658E
Terminal
No. Wire
color Item
Condition Data (Pyrex.)
1P Power supply
(Memory back-up) Always
Battery voltage
2P Power supply
(Memory back-up) Always
Battery voltage
3 L CAN-H – –
4V K-line (CONSULT-
II signal)
The terminal is connected to the data link connector for CONSULT-II.
–
5 B Ground Always0V
6 Y/R Power supply –
Battery voltage
– 0V
7R Back-up lamp
relay Selector lever in “
R” position. 0V
Selector lever in other positions. Battery voltage
8 P CAN-L ––
9 B/R Starter relay Selector lever in “
N”,“ P ” positions. Battery voltage
Selector lever in other positions. 0V
10 B Ground Always0V

TROUBLE DIAGNOSISAT-85
DE
F
G H
I
J
K L
M A
B
AT
Revision: November 2009 2006 QX56
ATF PRES SW 1Front brake engaged. Refer to
AT- 2 0ON
Front brake disengaged. Refer to AT- 2 0
OFF
ATF PRES SW 2 Low coast brake engaged. Refer to
AT- 2 0
ON
Low coast brake disengaged. Refer to AT- 2 0
OFF
ATF PRES SW 3 Input clutch engaged. Refer to
AT- 2 0
ON
Input clutch disengaged. Refer to AT- 2 0
OFF
ATF PRES SW 5 Direct clutch engaged. Refer to
AT- 2 0
ON
Direct clutch disengaged. Refer to AT- 2 0
OFF
ATF PRES SW 6 High and low reverse clutch engaged. Refer to
AT- 2 0
ON
High and low reverse clutch disengaged. Refer to AT- 2 0
OFF
I/C SOLENOID Input clutch disengaged. Refer to
AT- 2 0
0.6 - 0.8 A
Input clutch engaged. Refer to AT- 2 0
0 - 0.05 A
FR/B SOLENOID Front brake engaged. Refer to
AT- 2 0
0.6 - 0.8 A
Front brake disengaged. Refer to AT- 2 0
0 - 0.05 A
D/C SOLENOID Direct clutch disengaged. Refer to
AT- 2 0
0.6 - 0.8 A
Direct clutch engaged. Refer to AT- 2 0
0 - 0.05 A
HLR/C SOL High and low reverse clutch disengaged. Refer to
AT- 2 0
0.6 - 0.8 A
High and low reverse clutch engaged. Refer to AT- 2 0
0 - 0.05 A
ON OFF SOL Low coast brake engaged. Refer to
AT- 2 0
ON
Low coast brake disengaged. Refer to AT- 2 0
OFF
STARTER RELAY Selector lever in
“N ”,“ P ” position. ON
Selector lever in other position. OFF
ACCELE POSI Released accelerator pedal.
0.0/8
Fully depressed accelerator pedal. 8/8
CLSD THL POS Released accelerator pedal.
ON
Fully depressed accelerator pedal. OFF
W/O THL POS Fully depressed accelerator pedal.
ON
Released accelerator pedal. OFF
BRAKE SW Depressed brake pedal.
ON
Released brake pedal. OFF
Item name
Condition Display value (Approx.)

TROUBLE DIAGNOSISAT-87
DE
F
G H
I
J
K L
M A
B
AT
Revision: November 2009 2006 QX56
2. Touch “SELF-DIAG RESULTS ”.
Display shows malfunction experienced since the last erasing
operation.
Display Items List
X: Applicable, —: Not applicable
BCIA0031E
Items (CONSULT-II
screen terms) Malfunction is detected when... TCM self-
diagnosis OBD-II (DTC)
“ A/T ” with
CONSULT-II MIL indicator
lamp*1,
“ ENGINE ” with
CONSULT-II or
GST
CAN COMM CIRCUIT

When a malfunction is detected in CAN communications U1000 U1000
STARTER RELAY/
CIRC

If this signal is ON other than in P or N position, this is judged to be a
malfunction.
(And if it is OFF in P or N position, this too is judged to be a malfunc-
tion.) P0615
—
TCM

TCM is malfunctioning. P0700 P0700
PNP SW/CIRC

PNP switch 1-4 signals input with impossible pattern

“ P ” position is detected from N position without any other position
being detected in between. P0705 P0705
TURBINE REV S/CIRC

TCM does not receive the proper voltage signal from the sensor.

TCM detects an irregularity only at position of 4th gear for turbine revo-
lution sensor 2. P0717 P0717
VEH SPD SEN/CIR AT
(Revolution sensor)

Signal from vehicle speed sensor A/T (Revolution sensor) not input
due to cut line or the like

Unexpected signal input during running

After ignition switch is turned ON, unexpected signal input from vehicle
speed sensor MTR before the vehicle starts moving P0720 P0720
ENGINE SPEED SIG

TCM does not receive the CAN communication signal from the ECM. P0725 —
TCC SOLENOID/CIRC

Normal voltage not applied to solenoid due to cut line, short, or the like P0740 P0740
A/T TCC S/V FNCTN

A/T cannot perform lock-up even if electrical circuit is good.

TCM detects as irregular by comparing difference value with slip rota-
tion. P0744 P0744*2
L/PRESS SOL/CIRC

Normal voltage not applied to solenoid due to cut line, short, or the like

TCM detects as irregular by comparing target value with monitor value. P0745 P0745
TP SEN/CIRC A/T

TCM does not receive the proper accelerator pedal position signals
(input by CAN communication) from ECM. P1705 P1705
ATF TEMP SEN/CIRC

During running, the ATF temperature sensor signal voltage is exces-
sively high or low P1710 P0710
VEH SPD SE/CIR ·MTR

Signal (CAN communication) from vehicle speed sensor MTR not input
due to cut line or the like

Unexpected signal input during running P1721
—
A/T INTERLOCK

Except during shift change, the gear position and ATF pressure switch
states are monitored and comparative judgement made. P1730 P1730

AT-92
TROUBLE DIAGNOSIS
Revision: November 20092006 QX56
R POSI IND (ON-OFF display)——X
N POSI IND (ON-OFF display) ——X
D POSI IND (ON-OFF display) ——X
4TH POSI IND (ON-OFF display) ——X
3RD POSI IND (ON-OFF display) ——X
2ND POSI IND (ON-OFF display) ——X
1ST POSI IND (ON-OFF display) ——X
MANU MODE IND (ON-OFF display) ——X
Not mounted but displayed.
POWER M LAMP (ON-OFF display) ——X
F-SAFE IND/L (ON-OFF display) ——X
ATF WARN LAMP (ON-OFF display) ——X
BACK-UP LAMP (ON-OFF display) ——X
STARTER RELAY (ON-OFF display) ——X
PNP SW3 MON (ON-OFF display) ——X
C/V CLB ID1 ——X
C/V CLB ID2 ——X
C/V CLB ID3 ——X
UNIT CLB ID1 ——X
UNIT CLB ID2 ——X
UNIT CLB ID3 ——X
TRGT GR RATIO ——X
TRGT PRES TCC (kPa) ——X
TRGT PRES L/P (kPa) ——X
TRGT PRES I/C (kPa) ——X
TRGT PRE FR/B (kPa) ——X
TRGT PRES D/C (kPa) ——X
TRG PRE HLR/C (kPa) ——X
SHIFT PATTERN ——X
DRV CST JUDGE ——X
START RLY MON ——X
NEXT GR POSI ——X
SHIFT MODE ——X
MANU GR POSI ——X
VEHICLE SPEED (km/h) —XX Vehicle speed recognized by the TCM.
Voltage (V) ——XDisplays the value measured by the voltage
probe.
Frequency (Hz) ——X
The value measured by the pulse probe is dis-
played.
DUTY-HI (high) (%)
——X
DUTY-LOW (low) (%) ——X
PLS WIDTH-HI (ms) ——X
PLS WIDTH-LOW (ms) ——X
Monitored item (Unit)
Monitor Item Selection
Remarks
ECU
INPUT
SIGNALS MAIN SIG-
NALS SELEC-
TION
FROM
MENU