2006 INFINITI M35 ground

POWER DOOR LOCK SYSTEM
BL-35
C
D
E
F
G
H
J
K
L
MA
B
BL
Revision: 2006 January2006 M35/M45
Power Supply and Ground Circuit Check of BCMNIS001WZ
1. CHECK FUSE
Check the following fuse and fusible link.
50A fusible link (letter F , located in the fuse and fusible link box)
10A fuse [No.21, located in the fuse block (J/B)]
10A fuse [No.6, located in the fuse block (J/B)]
15A fuse [No.1, located in the fuse block (J/B)]
NOTE:
Refer to BL-24, "
Component Parts and Harness Connector Location" .
OK or NG
OK >> GO TO 2.
NG >> If fuse is blown, be sure to eliminate cause of malfunction before installing new fuse, refer to PG-
3, "POWER SUPPLY ROUTING CIRCUIT" .
2. CHECK POWER SUPPLY CIRCUIT
1. Turn ignition switch OFF.
2. Disconnect BCM connectors.
3. Check voltage between BCM and ground.
OK or NG
OK >> GO TO 3.
NG >> Repair or replace BCM power supply circuit.
3. CHECK GROUND CIRCUIT
Check continuity between BCM harness connector and ground.
OK or NG
OK >> Power supply and ground circuit are OK.
NG >> Repair or replace BCM ground circuit.
Terminals Condition
of ignition
switch
positionVoltage (V)
(Approx.) (+)
(–)
BCM connector Terminal
M311
GroundACC
Battery voltage 38 ON
M442
OFF
55
PIIB6296E
BCM connector Terminal Continuity
M2 52 Ground Yes
PIIB5935E

BL-36
POWER DOOR LOCK SYSTEM
Revision: 2006 January2006 M35/M45
Check Door Lock and Unlock Switch NIS001X0
1. CHECK POWER WINDOW SWITCH OUTPUT SIGNAL
With CONSULT-II
Check (“CDL LOCK SW ”, “CDL UNLOCK SW”) in DATA MONITOR mode with CONSULT-II.
Without CONSULT-II
1. Remove key from ignition switch, and the door of driver side and passenger side is closed.
2. Check signal between BCM connector and ground with oscilloscope when door lock and unlock switch
(driver side and passenger side) is turned “LOCK” or “UNLOCK”.
3. Make sure signals which are shown in the figure below can be detected during 10 second just after door
lock and unlock switch (driver side and passenger side) is turned “LOCK” or “UNLOCK”.
OK or NG
OK >> Door lock and unlock switch is OK.
NG >> GO TO 2.
Monitor item Condition
CDL LOCK SW LOCK : ON
UNLOCK : OFF
CDL UNLOCK SW LOCK : OFF
UNLOCK : ON
PIIA7068E
Terminal
Signal
(Reference value) (+)
(–)
BCM connector Terminal
M1 22 Ground
PIIB5957EPIIA1297E

POWER DOOR LOCK SYSTEM
BL-37
C
D
E
F
G
H
J
K
L
MA
B
BL
Revision: 2006 January2006 M35/M45
2. CHECK POWER WINDOW SWITCH GROUND
1. Turn ignition switch OFF.
2. Disconnect power window main switch and front power window switch (passenger side) connector.
3. Check continuity between power window main switch connector and ground.
4. Check continuity between power window sub-switch (front passenger side) connector and ground.
OK or NG
OK >> GO TO 3.
NG >> Repair or replace harness.
3. CHECK POWER WINDOW SERIAL LINK CIRCUIT
1. Disconnect BCM connector.
2. Check continuity between BCM connector and power window main switch connector.
3. Check continuity between BCM connector and power window sub-switch (front passenger side) connec-
tor.
OK or NG
OK >> Replace power window main switch.
NG >> Repair or replace harness.
Power window main
switch connectorTerminal Continuity
D11 17 Ground Yes
PIIB5937E
Power window
sub-switch
(front passenger side)
connectorTerminal Continuity
D46 11 Ground Yes
PIIB5941E
AB
Continuity
BCM connector TerminalPower window
main switch
connectorTerminal
M1 22 D10 14 Yes
PIIB5958E
AB
Continuity
BCM connector TerminalPower window
sub- switch
(front passenger side)
connectorTerminal
M1 22 D46 16 Yes
PIIB5959E

BL-38
POWER DOOR LOCK SYSTEM
Revision: 2006 January2006 M35/M45
Check Door Lock Actuator/Driver SideNIS001X1
1. CHECK OUTPUT SIGNAL
Check voltage between BCM connector and ground.
OK or NG
OK >> GO TO 2.
NG >> Replace BCM.
2. CHECK DOOR LOCK ACTUATOR CIRCUIT
1. Turn ignition switch OFF.
2. Disconnect BCM and front door lock actuator driver side connector.
3. Check continuity between BCM connector and front door lock
actuator driver side connector.
4. Check continuity between BCM connector and ground.
OK or NG
OK >> Replace front door lock actuator (driver side).
NG >> Repair or replace harness.
Terminals
Condition of
door lock and
unlock switchVoltage (V)
(Approx.) (+)
(–)
BCM connector Terminal
M250
GroundLock 0
Battery voltage 0
44 Unlock 0
Battery voltage 0
PIIB6060E
AB
Continuity
BCM connector TerminalDoor lock actu-
ator connectorTerminal
M250
D142
Ye s
44 1
A
Continuity
BCM connector Terminal
M250
Ground No
44
PIIB6061E

POWER DOOR LOCK SYSTEM
BL-39
C
D
E
F
G
H
J
K
L
MA
B
BL
Revision: 2006 January2006 M35/M45
Check Door Lock Actuator/Passenger SideNIS001X2
1. CHECK DOOR LOCK ACTUATOR SIGNAL
Check voltage between BCM connector and ground.
OK or NG
OK >> GO TO 2.
NG >> Replace BCM.
2. CHECK DOOR LOCK ACTUATOR CIRCUIT
1. Disconnect BCM and front door lock actuator passenger side connectors.
2. Check continuity between BCM connector and front door lock
actuator passenger side.
3. Check continuity between BCM connector and ground.
OK or NG
OK >> Replace front door lock actuator (passenger side).
NG >> Repair or replace harness.
Terminals
Condition of
door lock and
unlock switchVoltage (V)
(Approx.) (+)
(–)
BCM connector Terminal
M2 50
GroundLock 0
Battery voltage 0
M3 70 Unlock 0
Battery voltage 0
PIIB6062E
AB
Continuity
BCM connector TerminalDoor lock actu-
ator connectorTe r m i n a l
M2 50
D442
Ye s
M3 70 1
A
Continuity
BCM connector Terminal
M2 50
Ground No
M3 70
PIIB6063E

BL-40
POWER DOOR LOCK SYSTEM
Revision: 2006 January2006 M35/M45
Check Door Lock Actuator/Rear LHNIS001X3
1. CHECK DOOR LOCK ACTUATOR SIGNAL
Check voltage between BCM connector and ground.
OK or NG
OK >> GO TO 2.
NG >> Replace BCM.
2. CHECK DOOR LOCK ACTUATOR CIRCUIT
1. Disconnect BCM and rear door lock actuator LH connectors.
2. Check continuity between BCM connector and rear door lock
actuator LH connectors.
3. Check continuity between BCM connector and ground.
OK or NG
OK >> Replace door lock actuator/rear LH.
NG >> Repair or replace harness.
Check Door Lock Actuator/Rear RHNIS001X4
1. CHECK DOOR LOCK ACTUATOR SIGNAL
Check voltage between BCM connector and ground.
OK or NG
OK >> GO TO 2.
NG >> Replace BCM.
Terminals
Condition of
door lock and
unlock switchVoltage (V)
(Approx.) (+)
(–)
BCM connector Terminal
M250
GroundLock 0
Battery voltage 0
51 Unlock 0
Battery voltage 0
PIIB6064E
AB
Continuity
BCM connector TerminalDoor lock actu-
ator connectorTerminal
M250
D592
Ye s
51 1
A
Continuity
BCM connector Terminal
M250
Ground No
51
PIIB6383E
Terminals
Condition of
door lock and
unlock switchVoltage (V)
(Approx.) (+)
(–)
BCM connector Terminal
M250
GroundLock 0
Battery voltage 0
51 Unlock 0
Battery voltage 0
PIIB6064E

POWER DOOR LOCK SYSTEM
BL-41
C
D
E
F
G
H
J
K
L
MA
B
BL
Revision: 2006 January2006 M35/M45
2. CHECK DOOR LOCK ACTUATOR CIRCUIT
1. Disconnect BCM and rear door lock actuator RH connectors.
2. Check continuity between BCM connector and rear door lock
actuator RH connectors.
3. Check continuity between BCM connector and ground.
OK or NG
OK >> Replace door lock actuator/rear RH.
NG >> Repair or replace harness.
Check Fuel Lid Opener Actuator NIS001X5
1. CHECK FUEL LID OPENER ACTUATOR CIRCUIT
1. Turn ignition switch OFF.
2. Disconnect BCM and fuel lid lock actuator connector.
3. Check continuity between BCM connector and fuel lid lock actu-
ator connector.
4. Check continuity between BCM connector and ground.
OK or NG
OK >> Replace fuel lid lock actuator.
NG >> Repair or replace harness.
AB
Continuity
BCM connector TerminalDoor lock actu-
ator connectorTe r m i n a l
M250
D792
Ye s
51 1
A
Continuity
BCM connector Terminal
M250
Ground No
51
PIIB6383E
AB
Continuity
BCM connector TerminalFuel lid lock
actuator con-
nectorTe r m i n a l
M250
B1252
Ye s
51 1
A
Continuity
BCM connector Terminal
M250
Ground No
51
PIIB6066E

BL-42
POWER DOOR LOCK SYSTEM
Revision: 2006 January2006 M35/M45
Door Key Cylinder Switch CheckNIS001X6
1. CHECK DOOR KEY CYLINDER SWITCH INPUT SIGNAL
With CONSULT-II
Check (“KEY CYL LK-SW”, “KEY CYL UN-SW”) in “DATA MONITOR” mode for “POWER DOOR ROCK SYS-
TEM” with CONSULT-II.
Without CONSULT-II
1. Turn ignition switch OFF.
2. Check voltage between power window main switch connector and ground.
OK or NG
OK >> Key cylinder switch circuit is OK.
NG >> GO TO 2.
2. CHECK HARNESS CONTINUITY
1. Disconnect power window main switch and front door key lock assembly (driver side) connector.
2. Check continuity between power window main switch connector and front door lock assembly (driver side)
connector.
OK or NG
OK >> GO TO 3.
NG >> Repair or replace harness.
Monitor item Condition
KEY CYL LK-SWLock : ON
Neutral / Unlock : OFF
KEY CYL UN-SWUnlock : ON
Neutral / Lock : OFF
PIIA6285E
Te r m i n a l s
Key positionVoltage (V)
(Approx.) (+)
(–) Power window
main switch
connectorTerminal
D104
GroundLock 0
Neutral / Unlock 5
6Unlock 0
Neutral / Lock 5
PIIB5956E
AB
Continuity Power window
main switch
connectorTe r m i n a lFront door lock
assembly
(driver side)
connectorTerminal
D104
D146
Ye s
65
PIIB5973E