2006 INFINITI FX35 sensor

DI-24
COMBINATION METERS
Revision: 2006 December 2006 FX35/FX45
4. QUESTION 4
During driving, does the fuel gauge pointer move gradually toward EMPTY position?
YES >> Check the fuel level sensor unit. Refer to DI-24, "FUEL LEVEL SENSOR UNIT" .
NO >> The float arm may interfere or bind with any of the components in the fuel tank.
Odo/Trip Meter and Illumination Control Switch InspectionNKS002ZT
Symptom: Illumination control does not operate.
1. CHECK ODO/TRIP METER AND ILLUMINATION CONTROL SWITCH
1. Remove odo/trip meter and illumination control switch. Refer to DI-27, "
Removal and Installation of Odo/
Trip Meter and Illumination Control Switch" .
2. Check continuity odo/trip meter and illumination control switch. Refer to DI-24, "
ODO/TRIP METER AND
ILLUMINATION CONTROL SWITCH" .
OK or NG
OK >> Replace combination meter.
NG >> Replace odo/trip meter and illumination control switch.
Electrical Components InspectionNKS002ZW
ODO/TRIP METER AND ILLUMINATION CONTROL SWITCH
Check continuity between terminals 25, 26, 35 or 36 and 27.
FUEL LEVEL SENSOR UNIT
For removal, refer to FL-4, "FUEL LEVEL SENSOR UNIT, FUEL FILTER AND FUEL PUMP ASSEMBLY" .
Fuel Level Sensor Unit and Fuel Pump (Main)
Check the resistance between terminals 2 and 5.
*1 and *2: When float rod is in contact with stopper.

If the results of check are NG, check the fuel level sensor unit
and fuel pump (main) harness. Refer to DI-25, "
Fuel Level Sen-
sor Unit and Pump (Main) Harness" .
Terminal Condition Continuity
25
27 Illumination control switch (–) is pressed. Yes
Illumination control switch (–) is released. No
26 Illumination control switch (+) is pressed. Yes
Illumination control switch (+) is released. No
35 Trip transfer switch is pressed. Yes
Trip transfer switch is released. No
36 Trip reset switch is pressed. Yes
Trip reset switch is released. No
SKIB8529E
Terminal Float position [mm (in)] Resistance
value [ Ω]
25 *1 Full 236 (9.29) Approx. 3
*2 Empty 29 (1.14) Approx. 80
SKIB3550J

COMBINATION METERS DI-25
C
D E
F
G H
I
J
L
M A
B
DI
Revision: 2006 December 2006 FX35/FX45
Fuel Level Sensor Unit and Pump (Main) Harness
Check continuity at following terminals.

If the results of check are NG, replace fuel pump assembly. If the
results of check are OK, replace fuel level sensor unit.
Fuel Level Sensor Unit (Sub)
Check resistance between terminals 1 and 2.
*1 and *2: When float rod is in contact with stopper.
Removal and Installation of Combination MeterNKS003IC
Refer to IP-10, "INSTRUMENT PANEL ASSEMBLY" .
Disassembly and Assembly of Combination MeterNKS002ZY
Terminal Continuity
2 - Signal terminal (A) Ye s
5 - Ground terminal (B)
SKIB3551J
Terminal Float position [mm (in)] Resistance
value [ Ω]
12 *1 Full 6 (0.24) Approx. 3
*2 Empty 203 (7.99) Approx. 48
SKIB8530E
1. Rear cover 2. Screws 3. Plate
4. Unified meter control unit assembly 5. Front cover 6. Reinforcing metal
7. Switch and meter housing
SKIA5790E

DI-28
UNIFIED METER AND A/C AMP
Revision: 2006 December 2006 FX35/FX45
UNIFIED METER AND A/C AMPPFP:27760
System DescriptionNKS00300

For the unified meter and A/C amp., the signal required for controlling the combination meter are inte-
grated in the A/C auto amp.

The unified meter and A/C amp. corresponds to a CONSULT-II function (self-diagnosis results, CAN diag-
nosis support monitor, data monitor).
COMBINATION METER CONTROL FUNCTION

Unified meter and A/C amp. receives necessary information for combination meter from each unit by CAN
communication.

Unified meter and A/C amp. transmits a signals with communication line (TX, RX) between unified meter
and A/C amp. and combination meter.
Input/output signals between unified meter and A/C amp. and combination meter.
NOTE:
Combination meter performs fail-safe operation when unified meter and A/C amp. communication is malfunctioning. Refer to DI-8,
"FAIL-SAFE" . Unit Input Output
Unified meter and A/C amp.

Seat belt buckle switch signal (Driver's side)

Parking brake signal

Illumination control nighttime required signal

Refuel status signal

Low-fuel warning lamp condition signal

Combination meter receive error signal

Delivery destination data signal

Combination meter specifications signal

Vehicle speed signal (8-pulse)

Engine speed signal

Engine coolant temperature signal

Fuel level sensor signal (resistance value)

Malfunction indicator lamp signal

ABS warning lamp signal

Low tire pressure warning lamp signal

Brake warning lamp signal

A/T CHECK warning lamp signal

ICC warning lamp signal

Oil pressure switch signal

Door switch signal

AWD warning lamp signal

Key warning lamp signal

VDC OFF indicator lamp signal

SLIP indicator lamp signal

CRUISE indicator lamp signal

SET indicator lamp signal

High beam request signal

Turn indicator signal

Snow mode switch signal

ICC system display signal

Shift position indicator signal

Manual mode indicator signal

Manual mode gear position signal

CAN communication condition signal of A/T

Position lights request signal

Buzzer output signal

DI-96
LANE DEPARTURE WARNING SYSTEM
Revision: 2006 December 2006 FX35/FX45
Display Item
NOTE:

When a DTC is detected, the LDW system dose not operate.

When the DTC except “ABNRML TEMP DETECT [C1B03] ” is detected, the LDW indicator lamp turns ON.

When the DTC “ABNRML TEMP DETECT [C1B03] ” is detected, the LDW system ON indicator lamp blinks.
DATA MONITOR
Operation Procedure
1. Touch “DATA MONITOR” on “SELECT DIAG MODE” screen.
2. Touch any of “ALL SIGNALS” and “SELECTION FROM MENU” on selection screen.
3. Touch “START”.
4. Display the data monitor.
5. If necessary, touch “COPY” in turn, and print data.
Monitored Item
Display item [Code] Malfunctions detected where... Reference
page
CAMERA UNIT MALF [C1B00] LDW camera unit internal malfunction DI-100
CAM AIMING INCMP [C1B01] LDW camera aiming is not adjusted.DI-100
VHCL SPD DATA MALF [C1B02] LDW camera unit detected different vehicle speed signal from TCM and ABS
actuator and electric unit (control unit). DI-100
ABNRML TEMP DETECT [C1B03] Temperature around LDW camera unit is excessively high.
DI-101
CAN COMM CIRCUIT [U1000] LDW camera unit detected CAN communication malfunction.DI-101
CONTROL UNIT (CAN) [U1010] LDW camera unit detected internal CAN communication circuit malfunction.DI-101
Monitored Item [unit] Description
MAIN SW [ON/OFF] Displays [ON/OFF] status as judged from LDW switch signal.
SW ON LAMP [ON/OFF] Displays [ON/OFF] status of LDW system ON indicator signal output.
INDICATE LAMP [ON/OFF] Displays [ON/OFF] status of LDW indicator signal output.
BUZZER OUTPUT [ON/OFF] Displays [ON/OFF] status of LDW chime operation signal output.
LDW INACCURAT [ON/OFF] Displays LDW camera unit status.
VHCL SPD SE [km/h] or [mph] Displays vehicle speed calculated by LDW camera unit through CAN communication [ABS
actuator and electric unit (control unit) transmits wheel sensor signal through CAN commu-
nication].
VHCL SPD AT [km/h] or [mph] Displays vehicle speed calculated from A/T vehicle speed sensor by LDW camera unit
through CAN communication (TCM transmits A/T vehicle speed sensor signal through CAN
communication).
TURN SIGNAL [OFF/LH/RH] Displays “Turn signal” status, determined from BCM through CAN communication.
LANE DETCT LH [ON/OFF] Displays left lane marker is detected.
LANE DETCT RH [ON/OFF] Displays right lane marker is detected.
CROSS LANE LH [ON/OFF] Displays vehicle is crossing left lane.
CROSS LANE RH [ON/OFF] Displays vehicle is crossing right lane.
WARN LANE LH [ON/OFF] Displays warning for left lane.
WARN LANE RH [ON/OFF] Displays warning for right lane.
VALID POS LH [VLD/INVLD] Displays lateral position for left lane marker is valid.
VALID POS RH [VLD/INVLD] Displays lateral position for right lane marker is valid.
AIMING DONE [OK/NG] Displays camera aiming done.
AIMING RESULT [OK/NOK] Displays camera aiming result.
FCTRY AIM YAW [deg] Displays camera unit installation condition.
FCTRY AIM ROL [deg] Displays camera unit installation condition.

EC-1
ENGINE CONTROL SYSTEM
B ENGINE
CONTENTS
C
D E
F
G H
I
J
K L
M
SECTION EC
A
EC
Revision: 2006 December 2006 FX35/FX45
ENGINE CONTROL SYSTEM
VQ35DE
INDEX FOR DTC ................................................... ... 15
DTC No. Index .................................................... ... 15
Alphabetical Index ............................................... ... 19
PRECAUTIONS ..................................................... ... 23
Precautions for Supplemental Restraint System
(SRS) “AIR BAG” and “SEAT BELT PRE-TEN-
SIONER” ............................................................. ... 23
On Board Diagnostic (OBD) System of Engine and
A/T ....................................................................... ... 23
Precaution ........................................................... ... 23
PREPARATION ...................................................... ... 27
Special Service Tools .......................................... ... 27
Commercial Service Tools ................................... ... 29
ENGINE CONTROL SYSTEM ............................... ... 30
System Diagram .................................................. ... 30
Multiport Fuel Injection (MFI) System ................. ... 31
Electronic Ignition (EI) System ............................ ... 33
Fuel Cut Control (at No Load and High Engine
Speed) ................................................................. ... 34
AIR CONDITIONING CUT CONTROL .................. ... 35
Input/Output Signal Chart .................................... ... 35
System Description ............................................. ... 35
AUTOMATIC SPEED CONTROL DEVICE (ASCD) ... 36
System Description ............................................. ... 36
Component Description ....................................... ... 37
CAN COMMUNICATION ....................................... ... 38
System Description ............................................. ... 38
EVAPORATIVE EMISSION SYSTEM .................... ... 39
Description .......................................................... ... 39
Component Inspection ........................................ ... 42
Removal and Installation ..................................... ... 43
How to Detect Fuel Vapor Leakage .................... ... 43
ON BOARD REFUELING VAPOR RECOVERY
(ORVR) ................................................................... ... 46
System Description ............................................. ... 46
Diagnostic Procedure .......................................... ... 47
Component Inspection ........................................ ... 49 POSITIVE CRANKCASE VENTILATION ..............
... 51
Description ........................................................... ... 51
Component Inspection ......................................... ... 51
IVIS (INFINITI VEHICLE IMMOBILIZER SYSTEM-
NATS) ..................................................................... ... 53
Description ........................................................... ... 53
ON BOARD DIAGNOSTIC (OBD) SYSTEM ......... ... 54
Introduction .......................................................... ... 54
Two Trip Detection Logic ..................................... ... 54
Emission-Related Diagnostic Information ............ ... 55
Malfunction Indicator Lamp (MIL) ........................ ... 68
OBD System Operation Chart ............................. ... 72
BASIC SERVICE PROCEDURE ............................ ... 77
Basic Inspection .................................................. ... 77
Idle Speed and Ignition Timing Check ................. ... 82
VIN Registration .................................................. ... 83
Accelerator Pedal Released Position Learning ... ... 84
Throttle Valve Closed Position Learning .............. ... 84
Idle Air Volume Learning ..................................... ... 84
Fuel Pressure Check ........................................... ... 86
TROUBLE DIAGNOSIS ......................................... ... 88
Trouble Diagnosis Introduction ............................ ... 88
DTC Inspection Priority Chart .............................. ... 94
Fail-Safe Chart .................................................... ... 96
Symptom Matrix Chart ......................................... ... 97
Engine Control Component Parts Location ......... .101
Vacuum Hose Drawing ........................................ .107
Circuit Diagram .................................................... .108
ECM Harness Connector Terminal Layout .......... .110
ECM Terminals and Reference Value .................. .110
CONSULT-II Function (ENGINE) ......................... .119
Generic Scan Tool (GST) Function ...................... .130
CONSULT-II Reference Value in Data Monitor .... .133
Major Sensor Reference Graph in Data Monitor
Mode .................................................................... .136
TROUBLE DIAGNOSIS - SPECIFICATION VALUE .138
Description ........................................................... .138
Testing Condition ................................................. .138
Inspection Procedure ........................................... .138
Diagnostic Procedure .......................................... .139

EC-2Revision: 2006 December 2006 FX35/FX45
TROUBLE DIAGNOSIS FOR INTERMITTENT INCI-
DENT ...................................................................... .148
Description ........................................................... .148
Diagnostic Procedure .......................................... .148
POWER SUPPLY AND GROUND CIRCUIT .......... .149
Wiring Diagram .................................................... .149
Diagnostic Procedure .......................................... .150
Ground Inspection ............................................... .154
DTC U1000, U1001 CAN COMMUNICATION LINE .156
Description ........................................................... .156
On Board Diagnosis Logic ................................... .156
DTC Confirmation Procedure .............................. .156
Wiring Diagram .................................................... .157
Diagnostic Procedure .......................................... .158
DTC U1010 CAN COMMUNICATION .................... .159
Description ........................................................... .159
On Board Diagnosis Logic ................................... .159
DTC Confirmation Procedure .............................. .159
Diagnostic Procedure .......................................... .160
DTC P0011, P0021 IVT CONTROL ....................... .161
Description ........................................................... .161
CONSULT-II Reference Value in Data Monitor Mode .161
On Board Diagnosis Logic ................................... .162
DTC Confirmation Procedure .............................. .162
Diagnostic Procedure .......................................... .163
Component Inspection ......................................... .164
Removal and Installation ..................................... .164
DTC P0031, P0032, P0051, P0052 A/F SENSOR 1
HEATER ................................................................. .165
Description ........................................................... .165
CONSULT-II Reference Value in Data Monitor Mode
.165
On Board Diagnosis Logic ................................... .165
DTC Confirmation Procedure .............................. .165
Wiring Diagram .................................................... .167
Diagnostic Procedure .......................................... .170
Component Inspection ......................................... .172
Removal and Installation ..................................... .172
DTC P0037, P0038, P0057, P0058 HO2S2 HEATER .173
Description ........................................................... .173
CONSULT-II Reference Value in Data Monitor Mode .173
On Board Diagnosis Logic ................................... .173
DTC Confirmation Procedure .............................. .174
Wiring Diagram .................................................... .175
Diagnostic Procedure .......................................... .178
Component Inspection ......................................... .180
Removal and Installation ..................................... .180
DTC P0075, P0081 IVT CONTROL SOLENOID
VALVE .................................................................... .181
Component Description ....................................... .181
CONSULT-II Reference Value in Data Monitor Mode .181
On Board Diagnosis Logic ................................... .181
DTC Confirmation Procedure .............................. .181
Wiring Diagram .................................................... .182
Diagnostic Procedure .......................................... .186 Component Inspection .........................................
.187
Removal and Installation ...................................... .187
DTC P0101 MAF SENSOR .................................... .188
Component Description ....................................... .188
CONSULT-II Reference Value in Data Monitor Mode .188
On Board Diagnosis Logic ................................... .188
DTC Confirmation Procedure ............................... .189
Overall Function Check ........................................ .190
Wiring Diagram .................................................... .191
Diagnostic Procedure ........................................... .192
Component Inspection ......................................... .195
Removal and Installation ...................................... .196
DTC P0102, P0103 MAF SENSOR ........................ .197
Component Description ....................................... .197
CONSULT-II Reference Value in Data Monitor Mode .197
On Board Diagnosis Logic ................................... .197
DTC Confirmation Procedure ............................... .198
Wiring Diagram .................................................... .199
Diagnostic Procedure ........................................... .200
Component Inspection ......................................... .203
Removal and Installation ...................................... .204
DTC P0112, P0113 IAT SENSOR ........................... .205
Component Description ....................................... .205
On Board Diagnosis Logic ................................... .205
DTC Confirmation Procedure ............................... .205
Wiring Diagram .................................................... .207
Diagnostic Procedure ........................................... .208
Component Inspection ......................................... .209
Removal and Installation ...................................... .209
DTC P0117, P0118 ECT SENSOR ......................... .210
Component Description ....................................... .210
On Board Diagnosis Logic ................................... .210
DTC Confirmation Procedure ............................... .211
Wiring Diagram .................................................... .212
Diagnostic Procedure ........................................... .213
Component Inspection ......................................... .214
Removal and Installation ...................................... .214
DTC P0122, P0123 TP SENSOR ........................... .215
Component Description ....................................... .215
CONSULT-II Reference Value in Data Monitor Mode .215
On Board Diagnosis Logic ................................... .215
DTC Confirmation Procedure ............................... .216
Wiring Diagram .................................................... .217
Diagnostic Procedure ........................................... .218
Component Inspection ......................................... .221
Removal and Installation ...................................... .221
DTC P0125 ECT SENSOR ..................................... .222
Component Description ....................................... .222
On Board Diagnosis Logic ................................... .222
DTC Confirmation Procedure ............................... .223
Diagnostic Procedure ........................................... .223
Component Inspection ......................................... .224
Removal and Installation ...................................... .224
DTC P0127 IAT SENSOR ....................................... .225
Component Description ....................................... .225
On Board Diagnosis Logic ................................... .225

EC-3
C
D E
F
G H
I
J
K L
M
EC A
Revision: 2006 December 2006 FX35/FX45 DTC Confirmation Procedure ..............................
. 225
Diagnostic Procedure .......................................... . 226
Component Inspection ........................................ . 227
Removal and Installation ..................................... . 227
DTC P0128 THERMOSTAT FUNCTION ............... . 228
On Board Diagnosis Logic .................................. . 228
DTC Confirmation Procedure .............................. . 228
Diagnostic Procedure .......................................... . 228
Component Inspection ........................................ . 229
Removal and Installation ..................................... . 229
DTC P0130, P0150 A/F SENSOR 1 ...................... . 230
Component Description ....................................... . 230
CONSULT-II Reference Value in Data Monitor Mode . 230
On Board Diagnosis Logic .................................. . 230
DTC Confirmation Procedure .............................. . 230
Overall Function Check ....................................... . 231
Wiring Diagram ................................................... . 233
Diagnostic Procedure .......................................... . 236
Removal and Installation ..................................... . 239
DTC P0131, P0151 A/F SENSOR 1 ...................... . 240
Component Description ....................................... . 240
CONSULT-II Reference Value in Data Monitor Mode . 240
On Board Diagnosis Logic .................................. . 240
DTC Confirmation Procedure .............................. . 241
Wiring Diagram ................................................... . 242
Diagnostic Procedure .......................................... . 245
Removal and Installation ..................................... . 248
DTC P0132, P0152 A/F SENSOR 1 ...................... . 249
Component Description ....................................... . 249
CONSULT-II Reference Value in Data Monitor Mode
. 249
On Board Diagnosis Logic .................................. . 249
DTC Confirmation Procedure .............................. . 250
Wiring Diagram ................................................... . 251
Diagnostic Procedure .......................................... . 254
Removal and Installation ..................................... . 257
DTC P0133, P0153 A/F SENSOR 1 ...................... . 258
Component Description ....................................... . 258
CONSULT-II Reference Value in Data Monitor Mode . 258
On Board Diagnosis Logic .................................. . 258
DTC Confirmation Procedure .............................. . 259
Wiring Diagram ................................................... . 261
Diagnostic Procedure .......................................... . 264
Removal and Installation ..................................... . 269
DTC P0137, P0157 HO2S2 ................................... . 270
Component Description ....................................... . 270
CONSULT-II Reference Value in Data Monitor Mode . 270
On Board Diagnosis Logic .................................. . 270
DTC Confirmation Procedure .............................. . 271
Overall Function Check ....................................... . 271
Wiring Diagram ................................................... . 273
Diagnostic Procedure .......................................... . 276
Component Inspection ........................................ . 278
Removal and Installation ..................................... . 280 DTC P0138, P0158 HO2S2 ....................................
.281
Component Description ....................................... .281
CONSULT-II Reference Value in Data Monitor Mode .281
On Board Diagnosis Logic ................................... .281
DTC Confirmation Procedure .............................. .282
Overall Function Check ....................................... .283
Wiring Diagram .................................................... .284
Diagnostic Procedure .......................................... .287
Component Inspection ......................................... .291
Removal and Installation ..................................... .293
DTC P0139, P0159 HO2S2 .................................... .294
Component Description ....................................... .294
CONSULT-II Reference Value in Data Monitor Mode .294
On Board Diagnosis Logic ................................... .294
DTC Confirmation Procedure .............................. .295
Overall Function Check ....................................... .295
Wiring Diagram .................................................... .297
Diagnostic Procedure .......................................... .300
Component Inspection ......................................... .302
Removal and Installation ..................................... .304
DTC P0171, P0174 FUEL INJECTION SYSTEM
FUNCTION ............................................................. .305
On Board Diagnosis Logic ................................... .305
DTC Confirmation Procedure .............................. .305
Wiring Diagram .................................................... .307
Diagnostic Procedure .......................................... .311
DTC P0172, P0175 FUEL INJECTION SYSTEM
FUNCTION ............................................................. .317
On Board Diagnosis Logic ................................... .317
DTC Confirmation Procedure .............................. .317
Wiring Diagram .................................................... .319
Diagnostic Procedure .......................................... .323
DTC P0181 FTT SENSOR ..................................... .328
Component Description ....................................... .328
On Board Diagnosis Logic ................................... .328
DTC Confirmation Procedure .............................. .328
Wiring Diagram .................................................... .330
Diagnostic Procedure .......................................... .331
Component Inspection ......................................... .333
Removal and Installation ..................................... .333
DTC P0182, P0183 FTT SENSOR ......................... .334
Component Description ....................................... .334
On Board Diagnosis Logic ................................... .334
DTC Confirmation Procedure .............................. .334
Wiring Diagram .................................................... .335
Diagnostic Procedure .......................................... .336
Component Inspection ......................................... .338
Removal and Installation ..................................... .338
DTC P0222, P0223 TP SENSOR ........................... .339
Component Description ....................................... .339
CONSULT-II Reference Value in Data Monitor Mode .339
On Board Diagnosis Logic ................................... .339
DTC Confirmation Procedure .............................. .340
Wiring Diagram .................................................... .341
Diagnostic Procedure .......................................... .342

EC-4Revision: 2006 December 2006 FX35/FX45 Component Inspection .........................................
.345
Removal and Installation ..................................... .345
DTC P0300 - P0306 MULTIPLE CYLINDER MIS-
FIRE, NO. 1 - 6 CYLINDER MISFIRE .................... .346
On Board Diagnosis Logic ................................... .346
DTC Confirmation Procedure .............................. .347
Diagnostic Procedure .......................................... .347
DTC P0327, P0328 KS ........................................... .356
Component Description ....................................... .356
On Board Diagnosis Logic ................................... .356
DTC Confirmation Procedure .............................. .356
Wiring Diagram .................................................... .357
Diagnostic Procedure .......................................... .358
Component Inspection ......................................... .359
Removal and Installation ..................................... .360
DTC P0335 CKP SENSOR (POS) ......................... .361
Component Description ....................................... .361
CONSULT-II Reference Value in Data Monitor Mode .361
On Board Diagnosis Logic ................................... .361
DTC Confirmation Procedure .............................. .362
Wiring Diagram .................................................... .363
Diagnostic Procedure .......................................... .364
Component Inspection ......................................... .367
Removal and Installation ..................................... .367
DTC P0340, P0345 CMP SENSOR (PHASE) ........ .368
Component Description ....................................... .368
CONSULT-II Reference Value in Data Monitor Mode .368
On Board Diagnosis Logic ................................... .368
DTC Confirmation Procedure .............................. .369
Wiring Diagram .................................................... .370
Diagnostic Procedure .......................................... .373
Component Inspection ......................................... .376
Removal and Installation ..................................... .376
DTC P0420, P0430 THREE WAY CATALYST FUNC-
TION ....................................................................... .377
On Board Diagnosis Logic ................................... .377
DTC Confirmation Procedure .............................. .377
Overall Function Check ....................................... .378
Diagnostic Procedure .......................................... .379
DTC P0441 EVAP CONTROL SYSTEM ................ .383
System Description .............................................. .383
On Board Diagnosis Logic ................................... .383
DTC Confirmation Procedure .............................. .383
Overall Function Check ....................................... .384
Diagnostic Procedure .......................................... .385
DTC P0442 EVAP CONTROL SYSTEM ................ .388
On Board Diagnosis Logic ................................... .388
DTC Confirmation Procedure .............................. .389
Diagnostic Procedure .......................................... .390
DTC P0443 EVAP CANISTER PURGE VOLUME
CONTROL SOLENOID VALVE .............................. .397
Description ........................................................... .397
CONSULT-II Reference Value in Data Monitor Mode .397
On Board Diagnosis Logic ................................... .398
DTC Confirmation Procedure .............................. .398
Wiring Diagram .................................................... .399 Diagnostic Procedure ...........................................
.401
Component Inspection ......................................... .404
Removal and Installation ...................................... .404
DTC P0444, P0445 EVAP CANISTER PURGE VOL-
UME CONTROL SOLENOID VALVE ..................... .405
Description ........................................................... .405
CONSULT-II Reference Value in Data Monitor Mode .405
On Board Diagnosis Logic ................................... .406
DTC Confirmation Procedure ............................... .406
Wiring Diagram .................................................... .407
Diagnostic Procedure ........................................... .409
Component Inspection ......................................... .410
Removal and Installation ...................................... .411
DTC P0447 EVAP CANISTER VENT CONTROL
VALVE ..................................................................... .412
Component Description ....................................... .412
CONSULT-II Reference Value in Data Monitor Mode .412
On Board Diagnosis Logic ................................... .412
DTC Confirmation Procedure ............................... .413
Wiring Diagram .................................................... .414
Diagnostic Procedure ........................................... .415
Component Inspection ......................................... .417
DTC P0448 EVAP CANISTER VENT CONTROL
VALVE ..................................................................... .419
Component Description ....................................... .419
CONSULT-II Reference Value in Data Monitor Mode .419
On Board Diagnosis Logic ................................... .419
DTC Confirmation Procedure ............................... .420
Wiring Diagram .................................................... .421
Diagnostic Procedure ........................................... .422
Component Inspection ......................................... .423
DTC P0451 EVAP CONTROL SYSTEM PRESSURE
SENSOR ................................................................. .425
Component Description ....................................... .425
CONSULT-II Reference Value in Data Monitor Mode .425
On Board Diagnosis Logic ................................... .425
DTC Confirmation Procedure ............................... .426
Diagnostic Procedure ........................................... .426
Component Inspection ......................................... .427
DTC P0452 EVAP CONTROL SYSTEM PRESSURE
SENSOR ................................................................. .428
Component Description ....................................... .428
CONSULT-II Reference Value in Data Monitor Mode .428
On Board Diagnosis Logic ................................... .428
DTC Confirmation Procedure ............................... .429
Wiring Diagram .................................................... .430
Diagnostic Procedure ........................................... .431
Component Inspection ......................................... .433
DTC P0453 EVAP CONTROL SYSTEM PRESSURE
SENSOR ................................................................. .434
Component Description ....................................... .434
CONSULT-II Reference Value in Data Monitor Mode .434
On Board Diagnosis Logic ................................... .434