2006 INFINITI FX35 low oil pressure

ACS-14
[ICC]
LASER BEAM AIMING ADJUSTMENT
Revision: 2006 December 2006 FX35/FX45
LASER BEAM AIMING ADJUSTMENTPFP:00026
OutlineNKS003EQ
Adjust the laser beam aiming every time the ICC sensor is removed or installed.
CAUTION:

Adjust laser beam aiming at a horizontal place as far as 12 m (39 ft) forward the vehicle can be
seen.

Adjust laser beam aiming 5 seconds after starting engine.

Never view ICC sensor integrated unit body window directly during laser beam aiming adjustment.

Follow the CONSULT-ll when adjusting the laser beam aiming (laser beam aiming adjustment can-
not be operated without CONSULT-ll).

Never ride on vehicle during laser beam aiming adjustment.

Idle and turn headlamps OFF during laser beam aiming adjustment.
PreparationNKS003ER

Adjust the tire pressure to the specified value.

See that there is no load in the vehicle.

Coolant, engine oil filled up to correct level and full fuel tank.

Shift the gear into “P” position and release the parking brake.

Clean the ICC sensor with a soft cloth.
Outline of Adjustment ProcedureNKS003ES
1. Set up the ICC target board [KV99110100 (J-45718)].
2. Adjust the sensor following the procedure on CONSULT-II. (Turn manually the screw for up-down position adjustment. ICC sensor automatically adjust the right-left position.)
Setting the ICC Target BoardNKS003ET
Accurate ICC target board setting is required for the laser beam aiming adjustment.
CAUTION:
ICC system does not function normally if laser beam aiming is not accurate.
ADJUSTING HEIGHT OF THE TARGET
1. Attach a triangle scale at the center.
SKIA6179E
SKIA5974E

AT-4Revision: 2006 December 2006 FX35/FX45 A/T Does Not Shift: 5th Gear
→ 4th Gear ........... .219
A/T Does Not Shift: 4th Gear → 3rd Gear ........... .221
A/T Does Not Shift: 3rd Gear → 2nd Gear .......... .223
A/T Does Not Shift: 2nd Gear → 1st Gear ........... .225
Vehicle Does Not Decelerate by Engine Brake ... .227
SHIFT CONTROL SYSTEM ................................... .229
Control Device Removal and Installation ............. .229
Control Rod Removal and Installation ................. .230
Adjustment of A/T Position .................................. .231
Checking of A/T Position ..................................... .231
A/T SHIFT LOCK SYSTEM .................................... .232
Description ........................................................... .232
Shift Lock System Electrical Parts Location ........ .232
Wiring Diagram — AT — SHIFT .......................... .233
Diagnostic Procedure .......................................... .234
KEY INTERLOCK CABLE ..................................... .236
Components ........................................................ .236
Removal and Installation ..................................... .237
ON-VEHICLE SERVICE ......................................... .239
Control Valve with TCM and A/T Fluid Temperature
Sensor 2 .............................................................. .239
Parking Components (2WD Models Only) ........... .251
Rear Oil Seal ....................................................... .258
Revolution Sensor Components (2WD Models
Only) .................................................................... .259
AIR BREATHER HOSE .......................................... .264
Removal and Installation ..................................... .264
TRANSMISSION ASSEMBLY ............................... .266
Removal and Installation (2WD Models) ............. .266
Removal and Installation (AWD Models) ............. .269 OVERHAUL ............................................................
.274
Components ......................................................... .274
Oil Channel .......................................................... .288
Locations of Adjusting Shims, Needle Bearings,
Thrust Washers and Snap Rings ......................... .291
DISASSEMBLY ...................................................... .294
Disassembly ......................................................... .294
REPAIR FOR COMPONENT PARTS ..................... .312
Oil Pump .............................................................. .312
Front Sun Gear, 3rd One-way Clutch ................... .315
Front Carrier, Input Clutch, Rear Internal Gear .... .317
Mid Sun Gear, Rear Sun Gear, High and Low
Reverse Clutch Hub ............................................. .323
High and Low Reverse Clutch ............................. .329
Direct Clutch ........................................................ .332
ASSEMBLY ............................................................ .335
Assembly (1) ........................................................ .335
Adjustment ........................................................... .349
Assembly (2) ........................................................ .352
SERVICE DATA AND SPECIFICATIONS (SDS) ... .359
General Specifications ......................................... .359
Vehicle Speed at Which Gear Shifting Occurs ..... .359
Vehicle Speed at Which Lock-up Occurs/Releases .360
Stall Speed ........................................................... .360
Line Pressure ....................................................... .360
A/T Fluid Temperature Sensor ............................. .360
Turbine Revolution Sensor ................................... .361
Vehicle Speed Sensor A/T (Revolution Sensor) .. .361
Reverse Brake ..................................................... .361
Total End Play ...................................................... .361

A/T CONTROL SYSTEM AT-35
D E
F
G H
I
J
K L
M A
B
AT
Revision: 2006 December 2006 FX35/FX45
During Shift Change
The necessary and adequate line pressure for shift change is set.
For this reason, line pressure pattern setting corresponds to input
torque and gearshift selection. Also, line pressure characteristic is
set according to engine speed, during engine brake operation.
At Low Fluid Temperature
When the A/T fluid temperature drops below the prescribed tempera-
ture, in order to speed up the action of each friction element, the line
pressure is set higher than the normal line pressure characteristic.
Shift ControlNCS001B3
The clutch pressure control solenoid is controlled by the signals from the switches and sensors. Thus, the
clutch pressure is adjusted to be appropriate to the engine load state and vehicle driving state. It becomes
possible to finely control the clutch hydraulic pressure with high precision and a smoother shift change charac-
teristic is attained.
SHIFT CHANGE
The clutch is controlled with the optimum timing and oil pressure by the engine speed, engine torque informa-
tion, etc.
PCIA0010E
PCIA0011E
PCIA0012E

AT-38
A/T CONTROL SYSTEM
Revision: 2006 December 2006 FX35/FX45
Engine Brake ControlNCS001B5

The forward one-way clutch transmits the drive force from the engine to the rear wheels. But the reverse
drive from the rear wheels is not transmitted to the engine because the one-way clutch is idling.
Therefore, the low coast brake solenoid is operated to prevent the forward one-way clutch from idling and
the engine brake is operated in the same manner as conventionally.

The operation of the low coast brake solenoid switches the low coast brake switching valve and controls
the coupling and releasing of the low coast brake.
The low coast brake reducing valve controls the low coast brake coupling force.
Control ValveNCS001B6
FUNCTION OF CONTROL VALVE
SCIA1520E
Name Function
Torque converter regulator valve In order to prevent the pressure supplied to the torque converter from being excessive,
the line pressure is adjusted to the optimum pressure (torque converter operating pres-
sure).
Pressure regulator valve
Pressure regulator plug
Pressure regulator sleeve Adjusts the oil discharged from the oil pump to the optimum pressure (line pressure) for
the driving state.
Front brake control valve When the front brake is coupled, adjusts the line pressure to the optimum pressure
(front brake pressure) and supplies it to the front brake. (In 1st, 2nd, 3rd, and 5th gears,
adjusts the clutch pressure.)
Accumulator control valve Adjusts the pressure (accumulator control pressure) acting on the accumulator piston
and low coast reducing valve to the pressure appropriate to the driving state.
Pilot valve A Adjusts the line pressure and produces the constant pressure (pilot pressure) required
for line pressure control, shift change control, and lock-up control.
Pilot valve B Adjusts the line pressure and produces the constant pressure (pilot pressure) required
for shift change control.
Low coast brake switching valve During engine braking, supplies the line pressure to the low coast brake reducing valve.
Low coast brake reducing valve When the low coast brake is coupled, adjusts the line pressure to the optimum pressure
(low coast brake pressure) and supplies it to the low coast brake.
N-R accumulator Produces the stabilizing pressure for when N-R is selected.
Direct clutch piston switching valve Operates in 4th gear and switches the direct clutch coupling capacity.
High and low reverse clutch control valve When the high and low reverse clutch is coupled, adjusts the line pressure to the opti-
mum pressure (high and low reverse clutch pressure) and supplies it to the high and low
reverse clutch. (In 1st, 3rd, 4th and 5th gears, adjusts the clutch pressure.)

A/T CONTROL SYSTEM AT-39
D E
F
G H
I
J
K L
M A
B
AT
Revision: 2006 December 2006 FX35/FX45
FUNCTION OF ATF PRESSURE SWITCH
Input clutch control valve When the input clutch is coupled, adjusts the line pressure to the optimum pressure
(input clutch pressure) and supplies it to the input clutch. (In 4th and 5th gears, adjusts
the clutch pressure.)
Direct clutch control valve When the direct clutch is coupled, adjusts the line pressure to the optimum pressure
(direct clutch pressure) and supplies it to the direct clutch. (In 2nd, 3rd, and 4th gears,
adjusts the clutch pressure.)
TCC control valve
TCC control plug
TCC control sleeve Switches the lock-up to operating or released. Also, by performing the lock-up operation
transiently, lock-up smoothly.
Torque converter lubrication valve Operates during lock-up to switch the torque converter, cooling, and lubrication system
oil passage.
Cool bypass valve Allows excess oil to bypass cooler circuit without being fed into it.
Line pressure relief valve Discharges excess oil from line pressure circuit.
N-D accumulator Produces the stabilizing pressure for when N-D is selected.
Manual valve Sends line pressure to each circuit according to the select position. The circuits to which
the line pressure is not sent drain.
Name Function
Name Function
ATF pressure switch 1 (FR/B) Detects any malfunction in the front brake hydraulic pressure. When it detects any mal-
function, it puts the system into fail-safe mode.
ATF pressure switch 2 (LC/B) Detects any malfunction in the low coast brake hydraulic pressure. When it detects any
malfunction, it puts the system into fail-safe mode.
ATF pressure switch 3 (I/C) Detects any malfunction in the input clutch hydraulic pressure. When it detects any mal-
function, it puts the system into fail-safe mode.
ATF pressure switch 5 (D/C) Detects any malfunction in the direct clutch hydraulic pressure. When it detects any mal-
function, it puts the system into fail-safe mode.
ATF pressure switch 6 (HLR/C) Detects any malfunction in the high and low reverse clutch hydraulic pressure. When it
detects any malfunction, it puts the system into fail-safe mode.

AT-54
TROUBLE DIAGNOSIS
Revision: 2006 December 2006 FX35/FX45
8. Cool down the ATF. CAUTION:
Run the engine at idle for at least 1 minute.
9. Repeat steps 5 through 8 with selector lever in “R” position.
Judgement of Stall Test
O: Stall speed within standard value position
H: Stall speed higher than standard value
L: Stall speed lower than standard value
Stall test standard value position
LINE PRESSURE TEST
Line Pressure Test Port
Line Pressure Test Procedure
1. Inspect the amount of engine oil and replenish if necessary.
2. Drive the car for about 10 minutes to warm it up so that the ATF reaches in range of 50 to 80 °C (122 to
176 °F), then inspect the amount of ATF and replenish if necessary.
NOTE:
The A/T fluid temperature rises in range of 50 to 80 °C (122 to 176 °F) during 10 minutes of driving.
3. Remove the front propeller shaft from vehicle (with AWD models). Refer to PR-5, "
Removal and Installa-
tion" .
Selector lever position
Expected problem location
“D”, “M” “R”
Stall speed HO

Forward brake

Forward one-way clutch

1st one-way clutch

3rd one-way clutch
OH

Reverse brake
LL

Engine and torque converter one-way clutch
HH

Line pressure low
Does not shift-up “D” or “M” position 1 → 2 Slipping in 2nd, 3rd or 4th gear Direct clutch slippage
Does not shift-up “D” or “M” position 2 → 3 Slipping in 3rd, 4th or 5th gear High and low reverse clutch slippage
Does not shift-up “D” or “M” position 3 → 4 Slipping in 4th or 5th gear Input clutch slippage
Does not shift-up “D” or “M” position 4 → 5 Slipping in 5th gear Front brake slippage
SCIA2187E

AT-56
TROUBLE DIAGNOSIS
Revision: 2006 December 2006 FX35/FX45
Judgement of Line Pressure Test
ROAD TEST
Description

The road test checks overall performance of the A/T and analyzes possible malfunction causes.

The road test is carried out in the following three stages.
1. Check before engine is started. Refer to AT- 5 7
.
2. Check at idle. Refer to AT- 5 7
.
3. Cruise test

Inspect all the items from Part 1 to Part 3. Refer to AT- 5 8 , AT- 6 0 , AT- 6 1 .

Before beginning the road test, check the test procedure and inspection items.

Test all inspection items until the symptom is uncovered. Diagnose NG items when all road tests are com-
plete.
Judgement Possible cause
Idle speed Low for all positions
(“P”, “R”, “N”, “D”,
“M”) Possible causes include malfunctions in the pressure supply system and low oil pump output.
For example

Oil pump wear

Pressure regulator valve or plug sticking or spring fatigue

Oil strainer
oil pump
pressure regulator valve passage oil leak

Engine idle speed too low
Only low for a spe-
cific position Possible causes include an oil pressure leak in a passage or device related to the position after
the pressure is distributed by the manual valve.
High Possible causes include a sensor malfunction or malfunction in the line pressure adjustment func-
tion.
For example

Accelerator pedal position signal malfunction

ATF temperature sensor malfunction

Line pressure solenoid malfunction (sticking in OFF state, filter clog, cut line)

Pressure regulator valve or plug sticking
Stall speed Line pressure does
not rise higher than
the line pressure for
idle. Possible causes include a sensor malfunction or malfunction in the pressure adjustment function.
For example

Accelerator pedal position signal malfunction

TCM breakdown

Line pressure solenoid malfunction (shorting, sticking in ON state)

Pressure regulator valve or plug sticking

Pilot valve sticking or pilot filter clogged
The pressure rises,
but does not enter
the standard posi-
tion. Possible causes include malfunctions in the pressure supply system and malfunction in the pres-
sure adjustment function.
For example

Accelerator pedal position signal malfunction

Line pressure solenoid malfunction (sticking, filter clog)

Pressure regulator valve or plug sticking

Pilot valve sticking or pilot filter clogged
Only low for a spe-
cific position Possible causes include an oil pressure leak in a passage or device related to the position after
the pressure is distributed by the manual valve.

AT-74
TROUBLE DIAGNOSIS
Revision: 2006 December 2006 FX35/FX45
28 Slips/Will
Not
Engage No shock at all or the
clutch slips when
vehicle changes
speed D
2 → D3 or
M
2 → M3 . ON vehicle
1. A/T fluid level and state
AT- 5 3
2. Vehicle speed sensor A/T and vehicle speed sensor MTR AT- 11 8,
AT- 1 3 9
3. ATF pressure switch 6, high and low reverse clutch sole-
noid valve AT- 1 7 7,
AT- 1 5 8
4. CAN communication line AT- 1 0 4
5. Line pressure test AT- 5 4
6. Control valve with TCMAT- 2 3 9
OFF vehicle 7. Torque converter
AT- 2 9 4
8. Oil pump assemblyAT- 3 1 2
9. 3rd one-way clutchAT- 3 1 5
10. Gear systemAT- 2 7 4
11. High and low reverse clutchAT- 3 2 9
12. Forward one-way clutch (Parts behind drum support is
impossible to perform inspection by disassembly. Refer to
AT-18, "
Cross-sectional View (2WD Models)" , AT- 1 9 ,
"Cross-sectional View (VQ35DE Models for AWD)" or AT-
20, "Cross-sectional View (VK45DE Models for AWD)" ) AT- 2 9 4
13. Forward brake (Parts behind drum support is impossible
to perform inspection by disassembly. Refer to AT-18,
"Cross-sectional View (2WD Models)" , AT-19, "Cross-sec-
tional View (VQ35DE Models for AWD)" or AT- 2 0 , "Cross-
sectional View (VK45DE Models for AWD)" ) AT- 2 9 4
29No shock at all or the
clutch slips when
vehicle changes
speed D
3 → D4 or
M
3 → M4 . ON vehicle
1. A/T fluid level and state
AT- 5 3
2. Vehicle speed sensor A/T and vehicle speed sensor MTR AT- 11 8,
AT- 1 3 9
3. ATF pressure switch 3 and input clutch solenoid valve AT- 1 7 3,
AT- 1 4 6

4. ATF pressure switch 1 and front brake solenoid valve AT- 1 7 1
,
AT- 1 5 0
5. CAN communication line AT- 1 0 4
6. Line pressure test AT- 5 4
7. Control valve with TCMAT- 2 3 9
OFF vehicle 8. Torque converter
AT- 2 9 4
9. Oil pump assemblyAT- 3 1 2
10. Input clutchAT- 3 1 7
11. Gear systemAT- 2 7 4
12. High and low reverse clutchAT- 3 2 9
13. Direct clutchAT- 3 3 2
No. Items Symptom Condition Diagnostic Item Reference
page