2006 HONDA ACCORD COUPE ECU

µ
µ µ
µ
You
can also open both power
windows from outside the vehicle
with the remote transmitter (see
page ).
Press this button once
to unlock the driver’s door. Push it
twice to unlock the passenger’s door.
Some exterior lights will f lash twice
each time you push the button.
The ceiling light (if the ceiling light
switch is in the door activated
position) will come on when you
press the UNLOCK button. If you do
not open either door within 30
seconds, the lights f ade out. If you
relock the doors with the remote
transmitter before 30 seconds have
elapsed, the lights will go of f
immediately.
Press this button once to
lock both doors. Some exterior lights
will f lash once.
When you push the LOCK button
twice within 5 seconds, the lights will
flash and the horn will beep to verify
that the doors are locked and that
the security system has set. The
LOCK button will not work this way
if either door is not f ully closed. When the key is in the ignition
switch, the f unctions of each button
is disabled. Press this
button f or about 1 second to open
the trunk.
Press and hold this
button for about 2 seconds to attract
attention: the horn will sound and
the exterior lights will f lash f or about
30 seconds. To cancel panic mode,
press any other button on the remote
transmitter, or turn the ignition
switch to the ON (II) position.
If you do not open either door within
30 seconds, the doors automatically
relock and the security system sets. 92
UNL OCK
LOCK T RUNK REL EA SE
PA NIC
Remote Transmitter
78
UNLOCK
BUTTON
LOCK
BUTTON
TRUNK
RELEASE
BUTTON
PANIC
BUTTON
——y
y
(%y
y

To release the seat-back from inside
the trunk, pull the release under the
trunk panel. Push the seat-back
down, then let go of the release.
To lock the seat-back upright, push it
firmly against the trunk panel. Make
sure it is latched in place by pulling
on the top of the seat. Make
sure that the folded seat-back
does not interfere with the front
passenger’s seat-back. This will
cause the front passenger’s weight
sensors to work improperly (see
page ). Also check the passenger
airb ag off indicator to assu re proper
operation of the passenger’s
advanced front airbag.
Do not put any heavy items on the
seat-back when it is folded. Make
sure all items in the trunk, or
items extending through the opening
into the back seat, are secured.
Looseitemscanflyforwardand
cause injury if you have to brake
hard. See on page
.
Never drive with the seat-back
folded down and the trunk lid open.
See on
page .
Make sure all rear shoulder belts are
positioned in f ront of the rear seat-
back, and the center shoulder belt is
re-positioned in the guide whenever
the seat-back is in its upright position.
Be sure the center shoulder belt is
not twisted. 50
25
193
Seats
Carrying Cargo
Carbon Monoxide HazardInst rument s and Cont rols
89
Pull
——y

y
(%yy

The standard audio system has
many f eatures. This section de-
scribes those f eatures and how to
use them.
Your vehicle has an anti-theft audio
system that requires a code number
to enable it. The heating and cooling system in
your vehicle provides a comf ortable
driving environment in all weather
conditions.......
Heating and Cooling System .106
......................
Heating and A/C .108
..........
Climate Control System .113
Climate Control System
.......
with navigation system .117
.........
Dual Temperature Control .121
.............
Climate Control Sensors .123
...............................
Audio System .124
.................
AM/FM/CD Player .126
............
AM/FM/CD Changer .136
AM/FM/CD Changer
.......
with navigation system .149
...........
AM/FM Radio Reception .164
...
XM
Satellite Radio Reception . 166
...................
Protecting Your CDs .169
.........
Caring f or the Tape Player . 170
...............
Remote Audio Controls . 171
................
Radio Thef t Protection . 172
.........................
Setting the Clock .173
...........................
Security System .174
..............................
Cruise Control .175
HomeLink Universal ...............................
Transceiver .178
The security system helps to
discourage vandalism and thef t of
your vehicle.
On all models except the 4-cylinder LX
Features
Features
105
——y
y
(%y
y

Once the security system is set,
opening either door without using
the key or the remote transmitter,
the hood, or the trunk will cause the
system to alarm. It also alarms if the
radio is removed f rom the dashboard
or the wiring is cut.With the system set, you can still
open the trunk with the remote
transmitter without triggering the
alarm. The alarm will sound if the
trunk lock is f orced, or the trunk is
opened with the trunk release handle
or the emergency trunk opener.
The security system helps to protect
your vehicle and valuables f rom thef t.
The horn sounds and a combination
of headlights (low beam), parking
lights, side marker lights, and
taillights f lash if someone attempts
to break into your vehicle or remove
the radio. This alarm continues f or 2
minutes, then it stops. To reset an
alarming system before the 2
minutes have elapsed, unlock the
driver’s door with the key or the
remote transmitter.
The security system automatically
sets 15 seconds after you lock the
doors, hood, and trunk. For the
system to activate, you must lock the
doors f rom the outside with the key,
lock tab, door lock switch, or remote
transmitter. The security system
indicator on the instrument panel
starts blinking immediately to show
you the system is setting itself . The security system will not set if
the hood, trunk, or either door is not
f ully closed. Bef ore you leave the
vehicle, make sure the doors, trunk,
and hood are securely closed.
To see if the system is set
af ter you exit the vehicle, press the
LOCK button on the remote
transmitter within 5 seconds. If the
system is set, the horn will beep
once.
Do not attempt to alter this system
or add other devices to it.
Security System
174
NOTE:
SECURITY SYSTEM INDICATOR
——y
y
(%y
y

µ
If you are training HomeLink to
operate a garage door or gate, you
should unplug the motor for that
devi ce during training. Repeatedly
pressing the remote control button
could burn out the motor. They
do not have the safety feature
that causes the motor to stop and
reverse if an obstacle is detected
during closing, increasing the risk of
injury.
HomeLink stores the code in a
permanent memory. There should
be no need to retrain HomeLink if
your vehicle’s battery goes dead or is
disconnected. If your garage door
opener was manufactured before
April 1982, you may not be able to
program HomeLink to operate it.
The
HomeLinkuniversal
transceiver built into your vehicle
canbeprogrammedtooperateup to
three remotely controlled devices
around your home, such as garage
doors, lighting, or home security
systems.
For quick and accurate training,
make sure the remote control
transmitter for the device (garage
door, automatic gate, security
system, etc.) has a fresh battery. If
you just
receiv ed your vehicle and have not
trained any of the buttons in
HomeLink before, you should erase
any previously learned codes before
training the first button.
If you are training the second or
third buttons, go directly to step 1.
Unplug the garage door opener
motor from the electrical outlet.
Holdtheendofthegaragedoor
opener remote 2 to 5 inches from
HomeLink.Makesureyouarenot
blocking your view of the red
indicator in HomeLink.
Always
refer to the operating
instructions and safety information
that came with your garage door
opener or other equipment you
intend to operate with HomeLink. If
you do not have this information,
contact the manuf acturer of the
equipment. Todothis,pressandholdthetwo
outside buttons on the HomeLink
transceiver for about 20 seconds,
until the red indicator f lashes.
Release the buttons, then go to step
1.
2. 1.
On EX-V6 model
General Inf ormation
Important Saf ety PrecautionsT raining HomeL ink
Bef ore you begin
HomeL ink Universal Transceiver
178
——y

y
(%y

y

Plug in the garage door opener
motor, then test the HomeLink
button by pushing it for about 1 second.
If the button works,
programming is complete.
If the button does not work go
to step 6.
Press and hold the remote
transmitter button and one of the
HomeLink buttons at the same
time. If the red indicator in HomeLink
begins to flash slowly at first,
then rapidly, release both
buttons, and go to step 5. If the red indicator in HomeLink
continues to flash slowly (does
not flash rapidly), your remote
transmitter may stop
transmitting after a short time.
Go to step 4.
Press and hold the remote
transmitter button and one of the
HomeLink buttons at the same
time. While continuing to hold the
HomeLink button, press and
release the remote transmitter
button every 2 seconds. If the red indicator in HomeLink
begins to flash slowly at first,
then rapidly, release both
buttons, and go to step 5.
If the red indicator in HomeLink
continues to flash slowly (does
not begin to fl ash rapidly),
repeat steps 2 thru 4. Repeat these steps to train the
other two HomeLink buttons to
operate any other compatible
remotely controlled d
evices
around your home (lighting,
automatic gate, security system,
etc.). If
the indicator flashes rapidly
for 2 seconds then stays on, you
have a rolling code transmitter:
Go to ‘‘Training with a Rolling
Code System’’ (see page ). If the indicator stays on or
flashes slowly, repeat steps 2
thru 5.
PushandholdtheHomeLink
button f or a f ew seconds, then
watch the red indicator on
HomeLink.
3. 4.
5.6.
7.
180
HomeL ink Universal Transceiver
Features
179
——y
y
(%y
y

For security purposes, newer garage
door opening systems use a ‘‘rolling’’
or variable code. Information from
the remote control and the garage
door opener are needed bef ore
HomeLink can operate the garage
door opener.
The ‘‘Training HomeLink’’
procedure trains HomeLink to the
proper garage door opener code.
The f ollowing procedure
synchronizes HomeLink to the
garage door opener so it sends and
receives the correct codes.Make sure you have properly
completed the ‘‘Training
HomeLink’’ procedure. Press and hold the button on
HomeLink f or 3 to 4 seconds.
Press and hold the HomeLink
button again f or 3 to 4 seconds.
This should turn of f the training
indicator on the garage door
opener unit. (Some systems may
require you to press the button up
to three times.)
Press the HomeLink button again.
It should operate the garage door.
Find the ‘‘training’’ button on your
garage door opener unit. The
location will vary, depending on
the manufacturer. Press the training button on the
garage door opener unit until the
indicator next to the button comes
on. The indicator may blink, or
comeonandstayon.Youthen
have approximately 30 seconds to
complete the f ollowing steps.
6.
2. 4.
5.
1. 3.
T raining With a Rolling Code
System
HomeL ink Universal Transceiver
180
TRAINING BUTTON
——y
y
(%y
y

Lif t the hood up most of the way.
The hydraulic supports will lif t it
uptherestof thewayandholdit
up.
To close the hood, lif t it up slightly
to remove the support rod f rom
the hole. Put the support rod back
into its holding clip. Lower the
hood to about a f oot (30 cm) above
the fender, then let it drop. Make
sure it is securely latched. To close the hood, lower the hood to
about a f oot (30 cm) above the
f ender, then press down f irmly with
your hands. Make sure it is securely
latched.
Pull the support rod out of its clip
by holding the grip, and insert the
end into the designated hole in the
hood.
Put your f ingers under the f ront
edge of the hood. The hood latch
handle is above the ‘‘H’’ logo. Pull
this handle until it releases the
hood, then lif t the hood.
If the hood latch handle moves
stif f ly, or if you can open the hood
without lifting the handle, the
mechanism should be cleaned and
lubricated. 3.
2.
6-cylinder models
4-cylinder models
Service Station Procedures
Bef ore Driving
187
GRIP
CLIP
4-cylinder models 6-cylinder models
LATCH
——y
y
(%y
y