2006 GREAT WALL HOVER wheel

Safety airbag-26
Do the troubleshooting if the alarm lamp re-illuminates after its extinguishments following the 6-second-flashing (or it keeps
illuminating from the very beginning)
10. Test
a. Driver’s side airbag module test (Figure8-3)
Check the following items and replace the corresponding safety airbag module part with anything abnormal with a new one.
Abandon the safety airbag’s old parts after its release according to the instructed procedure.
Caution
Do not jam the clock spring wiring harness during the steering wheel and safety airbag module assembly installation.
After the installation, rotate the steering wheel to left and right positions as enough as possible to confirm whether something
abnormal is with it.
d. Post-installation test.
lightly rotate the steering wheel to the left and right to confirm whether something abnormal and noises will arise.(Driver’s side
safety airbag module, clock spring)
Place the ignition switch in ON place.
SRS alarm lamp flashes in 6 seconds and then extinguishes.
Caution
If without the clock spring central involution, the steering wheel will not be able to rotate at midway, or the clock spring
circuit will be damaged so that jeopardize SRS safety airbag’s normal activities.
The spacer must be removed after replacing a clock spring with a new one, otherwise it will damage the clock spring.
c. Steering wheel and safety airbag module assembly installation.
Install the steering wheel and safety airbag module assembly after clock spring’s central involution.
safety airbag system failure alarm lamp
Caution
The safety airbag module (squib) circuit resistance can even not be tested by the designated tester.
When testing the resistance with an experimental instrument, sometimes the improper release will be caused by the
static interference because of the current in explosion pipe and cause some major damaging accidents.
Whether depression, crack or deformation is with the shroud.
Whether the joint is broken and the terminal is deformed.
Whether depression, crack or deformation is with the gas generator shield.
Safety airbag module. Installation status.
Caution
Replace the safety airbag with depression, crack or deformation with a new one. Its old parts must be abandoned after
its release.

Safety airbag-31
release wiring harness.
driver’s side safety airbag module
release wiring harness
Installed the stand-by bolts on the driver’s side safety airbag module’s inside bolt and fasten a thick wire to the wheel rim to
fix it.
Connect the release wiring harness connecting with the driver’s side safety airbag module with the low part of an old tire loading
the wheel rim. ( refer to figure 9-6)
Lay three wheel-hub-free old tires on the tire fixing the driver’s side safety airbag module (Figure 9-7).
wheel-hub-free old tires
release wiring harness
Shut off the joint of driver’s side safety airbag release wiring harness somewhere far from the vehicle, and connect the joint with
the accumulator and make the safety airbag release (Figure9-8).
Caution
Release the driver’s side safety airbag module after the confirmation of nobody close to it.
Its gas generator is quite hot after the driver’s side safety airbag’s release, it can be used after its cooling down for more
than 30 minutes.
Contact with the local service station of the Great Wall Auto Stock Corporation if the driver’s side safety

Safety airbag-18
Nor mal Present failure code
Replace SRS safety airbag system
unit
Take references in
removal/installation of SRS
safety airbag system unit in safety
airbag system.
History-accumulated failure
codes
The end of failure diagnosis
4 Check the wiring harness between passengers’ side safety airbag
module and SRS safet y airbag system electronic-control unit
Place the ignition switch in LOCK position
Release accumulator negative wire and then wait for about 1
minute plus
Remove steering pillar shell
Release clock spring connector clip
Release driver’s and passengers’ side safety airbag module
connector clips
Release all SRS safety airbag system unit connector clips
Check whether the following troubles are with the circuit of the
connector clips terminals between SRS safety airbag system
electronic-control unit and passengers’ side safety airbag
module
Grounding
Power-supply shorting
Shutoff
Is the previous circuit normal? Abnormal Replace the relative wiring
harness
Impact-vehicle diagnosis
Test SRS-ECU diagnostic signals
1. Connect the (X-431 diagnostic test’s) diagnostic joint
2. Read the diagnostic results with X-431 diagnostic tester
Repairing procedure
1.When safety airbag is released.
The following parts should be replaced with new ones
a. Passengers’ side safety airbag module
b. SRS-ECU
c. Driver’s side safety airbag module
2 Check the following parts; replace them with new ones providing something wrong with them.
a. Clock spring
b. Steering-wheel, steering column, bottom steering shaft module
3.Driver’s side safety airbag module’s installation status towards the steering wheel.
a. Check whether abnormal knocking is with the steering wheel, its activity is in good condition and its clearance is normal.
b. Check whether the wiring harness joint is broken and its terminal is deformed.
Caution: Due to the impact, the diagnostic instrument cannot communicate with SRS-ECU when accumulator is lack of
power, in this case, check and maintain the instrument panel wiring harness or utilize the extension power supply.

Appendix A-3
1. (upper suspension arm steering knuckle ball pin nut) bolt
Locate the rear transverse stabilizer rob in the corresponding
position of carriage, symmetries the left and right during
installation.
Connection of rear transverse
stabilizer rod and rear axleViewing confirmation
the fixed torque of nut 2 in the Figure is 23
3NmTorque wrench
Connection of rear transverse
stabilizer rod and rear transverse
stabilizer robs connecting bar
assembly.the fixed torque of nut 1 in the Figure is 63
5NmTorque wrench
rear transverse stabilizer
rear transverse stabilizer rod connecting bar assembly bush
Upper suspension arm and upper suspension
arm steering knuckle ball pin
Steering gear cross tie ball pin
Lower suspension arm and lower suspension
arm steering knuckle ball pinthe fixed torque of nut 1 in the Figure is
145
15Nm
the fixed torque of nut 2 in the Figure is120
10Nm
the fixed torque of nut 3 in the Figure is 230
20Nm
Torque wrench
Torque wrench
Torque wrench
2. (steering gear cross tie ball pin nut) left steering
knuckle and wheel hub brake assembly
3. (lower suspension arm steering knuckle ball pin nut bolt 4. left steering knuckle and steering knuckle
and wheel hub brake assembly.

Appendix A-11
Driver seat assembly installationbolt 1 in the Figure tightening torque:is 3343Nm
Wheel nut fixing procedure
Wheel nut fixed torqueInstallation order is A-C-E-B-D-F as showed in the Figure
Torque wrench
Viewing and handle
confirmation The headrest can be up and down smoothly, angle-adjuster
handle can be normally used, driver, co-driver seat can move
freely and transmission trim cover can be freely opened.
seat assembly
the fixed torque of nut 1 in the Figure is 135
15Nm
brake disc assembly

Appendix D-17
Serial
No. Working region and
specification Torque
N·m Serial
No. Working region and specification Torque
N·m
1 upper arm shaft fixed
bolt M14×1.5-10.9 200 25 engine suspension connecting bolt M10×
1.25-10.9 78±10
2 front shaft of lower arm
connecting bolt M16×
1.5-10.9 270±25 26 transmission suspension connecting bolt M10×
1.25-10.9 78±10
3 rear shaft of lower arm
connecting bolt M18×
1.5-10.9 320±30 27 transmission-engine connecting bolt M10×
1.25-10.9 50±5
4 b ottom ar m l imit ing
stopper fixed bolt M10
×1.25-8.8 63±5 28 drive shaft connecting bolt M10×1.25-10.9 78±5
5 upper arm ball pin
pedestal connecting bolt
M10×1.25-10.9 78±10 29 drive shaft bearing fixed bolt M10×1.25-8.8
65±5
6 bottom ar m ball p in
pedestal connecting bolt
M12×1.25-10.9 140±10 30 wheel nut M12×1.25 135±15
7 front twisted bar
pedestal connecting bolt
M12×1.25-10.9 140±10 31 steering wheel lock nut M12×1.25-8 30±5
8 upper arm ball channel
fixing nut M16×1.5-10 145±15 32 steering gear-carriage fixing nut M12×1.25-8 90±10
70±10
9 front vibration damper
upper fixing nut M10×
1.25-8 Bush
co mpr es sed
by 1/3 33
steering angle drive co-carriage bolt M10×
1.5-9.8 50±5
10 bottom ar m ball p in
channel fixing nut M18
×1.5-10 230±20 34 steering system universal-joint lock bolt M8×
1.25-8.8 25±3
11 front vibration damper
bottom connecting bolt
M12×1.25-8.8 90±10 35 steering linkage ball fixing nut M14×1.5-8 120±10
12 rear vibration damper
upper fixing nut M10×
1.25-8 Bush
co mpr es sed
by 1/3 36 steering linkage adjustment lock nut M14×
1.5-8 60±5
13 rear vibration damper
bottom fixing nut M14
×1.5-8 170±15 37 front axle front shackle connecting bolt M14×
1.5-10.9 180±20
14 front cross stabilizer rod
-carriage fixed bolt M8
×1.25-8.8 23±3 38 front axle rear shackle connecting bolt M14
×1.5-10.9 180±20

Appendix D-18
15 front cross stabilizer rod
-connecting bar bottom
arm bolt M10×1.25-8 63±5 39 brake petrol pipe joint M10×1.25 16
16 long longitudinal tie
connecting bolt M14×
1.5-10.9 200±20 40 safety belt body connecting bolt 7/16″-8.8
40±2
17 short longitudinal tie
front connecting bolt
M14×1.5-10.9 180±15 41 safety belt seat connecting bolt 7/16″-8.8 40±2
18 short longitudinal tie rear
connecting bolt M14×
1.5-10.9 200±20 42 body suspension connecting bolt M10×1.25-9.8 63±5
19 cross tie -carriage
connecting bolt M14×
1.5-10.9 200±20 43 Engine oil pan drain bolt 40±5
20 cross tie -rear axle fixing
nut M14×1.5-8 180±15 44 Transmission/transfer case refueling/drain bolt 30～35
21 rear cross stabilizer rod
-rear axle fixed bolt M8
×1.25-8.8 23±3 45 front drive axle refueling bolt M20×1.5 145±5
22 rear cross stabilizer rod
-connecting bar -carriage
bolt M10×1.25-8 63±5 46 Front drive axle drain bolt Rc1/2 30～35
23 standby tire bracket fixed
bolt 10×1.25-8.8 63±5 47 rear drive axle refueling/drain bolt M20×1.5 145±5
24 standby tire lifter fixed
bolt M8×1.25-8.8 25±3 48 Starter and wheel box connecting bolt 30±3