2006 DODGE SPRINTER Owners Manual

MAINTAINING YOUR VEHICLE 289
7
Taillamps
Cargo/Passenger Van
Locked (1)
Unlocked (2)
Bulbs are changed from inside the cargo area.
The rear lamp cluster bulb holder is located behind the
interior paneling. Remove the paneling.Brake lamp, taillamp, standing lamp,
P21/5W – 12V 21/5W (1)
Backup lamp, P21W – 12V 21W (2)
Turn signal lamp, P21W – 12V 21W (3)
Side-marker lamp, R5W – 12V 5W (4)
1. Unclip and remove the bulb socket.
2. To change a bulb, press the bulb into the bulb
socket, turn it counterclockwise and remove.
3. Insert the new bulb.
4. Clip the bulb socket into place.

290 MAINTAINING YOUR VEHICLE
Chassis
(1) Retaining screws
(2) Clearance lamp, R5W - 12V 5W
(3) Turn signal lamp, P21W - 12V 21W
(4) Stop lamp, P21W - 12V 21W
(5) Taillamp, R5W - 12V 5W
(6) Backup lamp, P21W - 12V 21W
(7) License plate lamp (driver‘s side only),
R5W - 12V 5W1. Loosen retaining screw a and remove lamp
housing.
2. To change a bulb, press the bulb into the bulb
socket, turn it counterclockwise and remove.
3. Insert the new bulb.
4. Install lamp housing.

MAINTAINING YOUR VEHICLE 291
7
License Plate Lamps
(Cargo/Passenger Vans Only)
1. Press the bulb socket to the left, against the force of
the spring, and remove.
2. Replace the bulb, C5W – 12V 5W.
3. Install the cover.
4. Re-install the bulb socket.Additional Brake Lamp
(Cargo/Passenger Vans Only)
(1) Retaining screws
1. Take out the retaining screws (1) and remove the
lamp housing.
2. To change a bulb, P21W – 12V 21W
Press the bulb into the bulb socket, turn it
counterclockwise and remove.
3. Insert the new bulb.
4. Install the lamp housing.

292 MAINTAINING YOUR VEHICLE
Side-Mounted Turn Signals
1. Press the lamp housing to the front, against the
force of the spring, and remove.
2. Replace the bulb, W5W - 12V 5W
3. Install the bulb socket.Side-Marker Lamps,
Standing Lamps (Optional)
Retaining screws (1) Bulb socket (2)
1. Take out the retaining screws (1) and remove the
lamp housing.
2. Turn the bulb socket (2) counterclockwise and
remove.
3. Replace the bulb, W3W – 12V 3W.
4. Install the bulb socket (2).

MAINTAINING YOUR VEHICLE 293
7
Identification Lamps (Cargo/passenger vans only)
(1) Retaining screw
1. Take out the retaining screw (1) and remove the
lamp housing.
2. To change a bulb, 12V 4CP
Press the bulb into the bulb socket, turn it
counterclockwise and remove.
3. Insert the new bulb.
4. Install the lamp housing.Interior Lighting in Passenger Compartment and
Load Compartment
1. Align a screwdriver on the retaining spring, press it
in and pry the lamp housing out.
2. Replace the bulb, K – 12V 18W
3. Install the lamp housing.

294 MAINTAINING YOUR VEHICLE
Interior Lighting with Reading Lamp
1. Use a screwdriver on the catch spring to press in
and remove the bulb housing.
2. Replace the bulb, K – 12V 10W.
3. Install the lamp housing.Interior Lighting with Interior Sensor Protection
1. Use a screwdriver on the catch spring, remove the
bulb housing.
2. Turn the bulb holder with the bulb in the direction
of the arrow and remove it.
3. Replace the bulb holder and bulb, K – 12V 6W
4. Install the lamp housing.

MAINTAINING YOUR VEHICLE 295
7
Exit Lamps (Optional)
(1) Lamp housing
(2) Cable connector
(3) Bulb holder1. Use a screwdriver on the catch spring to remove the
lamp housing (1).
2. Press the locating spring on the cable connector (2),
hold it down, and remove the cable connector (2).
3. Turn the bulb holder (3) to the left and remove it.
4. Replace the bulb, W5W - 12V 5W.
5. Install the bulb holder (3) and attach the cable
connector (2).

296 MAINTAINING YOUR VEHICLE
CAPACITIES
Engine with oil filter
Engine oilFuel tank Cooling system Windshield washer
system
Including
reserve fuel
All vehicles about
9.5 US qt
(9.0 l)about
26.4 US gal
(100 l)about
2.8 US gal
(10.5 l)about
2.7 US gal
(10.0 l)about
7.4 US qt
(7.0 l)