Page 97 of 295

The driving position memory
activated (Driver 1, Driver 2) is
shownonthebackof each
transmitter. Make sure you store
your desired driving position in the
memory that is activated by the
transmitter you normally carry.
You can turn of f this driving position
memory activation. Press and hold
the LOCK and UNLOCK buttons at
thesametime.TheLEDinthe
remote transmitter will blink twice.
Then release the buttons. Doing this
also cancels the keyless memory
settings f or that remote and restores
the default settings.
To turn it back on, repeat this
procedure. The LED will come on
for 1 second to indicate the feature
has been turned on.Avoid dropping or throwing the
transmitter.
Protect the transmitter from
extreme temperature.
Do not immerse the transmitter in
any liquid.
Each remote transmitter also
activates the driving position
memory system and changes the
keyless memory settings related to
that remote (see page ). When
you open the driver’s door af ter
unlocking it with the remote
transmitter, you will hear a beep.
The driver’s seat and outside mirrors
move to the positions stored in that
memory location. You will hear two beeps when the movement is
completed.
If you lose a transmitter, the
replacement needs to be
reprogrammed by your dealer.
103
Remote Transmitter
Recalling a Memorized Driving
PositionRemote Transmitter Care
96
With Driver 1 With Driver2
Page 98 of 295

µ
If it takes several pushes on the
button to lock or unlock the doors,
replace the battery as soon as
possible.
Battery type: CR2025
To replace the battery, place a cloth
on the edge of the transmitter and
remove the upper half by carefully
prying on the edge with a small f lat-
tip screwdriver. Remove the old
battery and insert a new battery with
the side f acing up. Snap the two
halves of the transmitter case back
together.
As required by the FCC:
This device complies with Part 15 of theFCC rules. Operation is subject to thef ollowing two conditions: (1) This devicemay not cause harmf ul interf erence, and(2) this device must accept anyinterf erence received, includinginterf erence that may cause undesiredoperation.
Changes or modif ications not expresslyapproved by the party responsible f orcompliance could void the user’sauthority to operate the equipment.
This device complies with IndustryCanada Standard RSS-210.Operation is subject to the f ollowing twoconditions: (1) this device may not causeinterf erence, and (2) this device mustaccept any interf erence that may causeundesired operation of the device.
Remote Transmitter
Replacing the Transmitter
Battery
Inst rument s and Cont rols
97
BATTERY
Page 99 of 295

µ
See pages f or important saf ety
inf ormation and warnings about how toproperly position seats and seat-backs. 13 14
The controls f or the power
adjustable front seats are on the
outside edge of each seat bottom.
You can adjust the seats with the
ignition switch in any position. Make
all seat adjustments bef ore you start
driving.
Moving the long horizontal switch on
the driver’s seat adjusts the seat
bottom in several directions. On the
passenger’s seat, the long horizontal
switch moves the seat only back and
f orth. The short vertical switch
adjusts the seat back angle.
The short horizontal switch on the
driver’s seat adjusts the degree of
lumbar support. Moves the seat forward
and backward.
Moves the seat up or
down and the rear of the
seat up or down.
(Driver’s seat only)
Raises or lowers the seat.
(Driver’s seat only)
Adjusts the seat-back
angle f orward or
backward.
Increases or decreases
the lumbar support.
(Driver’s seat only)
Seats
Front Seat Power A djustments
98
PASSENGER’S SEAT
DRIVER’S SEAT
Page 100 of 295

See page f or important saf etyinf ormation and a warning about how toproperly position the head restraints. 15
The head restraints help protect you
and your passengers f rom whiplash
and other injuries. They are most
ef f ective when you adjust them so
the back of the occupant’s head rests
against the center of the restraint. A
taller person should adjust the
restraint as high as possible.
All head restraints adjust f or height.
The tilt of the f ront head restraints is
also adjustable. You need both hands
to adjust the restraint. Do not
attempt to adjust it while driving. To
raise it, pull upward. To lower the
restraint, push the release button
sideways, and push the restraint
down. To adjust the tilt, pivot the
f ront head restraint to the desired
position.The lid of the console compartment
canbeusedasanarmrestbymoving
it f orward and backward. Make sure
the armrest is securely latched.
Make sure your passenger’s hands
orfingersareawayfromthearmrest
bef ore moving it.
Seats
Head Restraints
A rmrest
Inst rument s and Cont rols
99
RELEASE BUTTON
Page 101 of 295
Make sure all items in the trunk and
those extending through the pass-
through are secured.
Never drive with this cover open and
the trunk lid open.
Seeon
page .
The trunk pass-through cover can be
opened f rom either side; it f olds
f orward onto the center armrest.
Open the cover by sliding the knob
downward and pushing or pulling on
the cover. To close the cover, swing
it up and push f irmly on the top.
Make sure it latches properly.
The rear seat armrest is in the
center of the rear seat. Pivot it down
to use it. For security, this cover can be
locked and unlocked only with the
master key. To lock the cover, insert
thekey,andturnitclockwise.
53
Carbon Monoxide Hazard
T runk Pass-through Cover
Seats, Trunk Pass-through Cover
100
KNOB
COVER
Page 102 of 295
Keeptheinsideandoutsidemirrors
clean and adjusted f or best visibility.
Be sure to adjust the mirrors bef ore
you start driving.The inside mirror can automatically
darken to reduce glare. To turn on
this feature, press the button on the
bottom of the mirror. The AUTO
indicator comes on as a reminder.
When it is on, the mirror darkens
when it senses the headlights of a
vehicle behind you, then returns to
normal visibility when the lights are
gone. Press the button again to turn
of f this sensing. Move the selector switch to L
(driver’s side) or R (passenger’s
side).
Push the appropriate edge of the
adjustment switch to move the
mirrorright,left,up,ordown.
1.
2.
Mirrors
Adjusting the Power Mirrors
Inst rument s and Cont rols
101
SELECTOR SWITCH
ADJUSTMENT
SWITCH
Page 103 of 295

When you f inish, move the
selector switch to the center (off)
position. This turns of f the
adjustment switch to keep your
settings.The outside mirrors are heated to
remove fog and frost. With the
ignition switch in the ON (II)
position, turn on the heaters by
pressing the button. The indicator in
the button comes on as a reminder.
Press the button again to turn the
heaters off.
Depending on the position of the
selector switch, the lef t or right side
mirror will pivot downward slightly
when you shif t the transmission into
reverse. In the lef t position, the lef t
mirror pivots. In the right position,
the right mirror pivots. This gives
you a better view of that side of the
vehicle while parallel parking. The
mirror returns to its original position
when you take the transmission out
of reverse. To turn this f eature of f ,
leave the switch in the center
position.
Outside mirror positions can be
stored in the driving position
memory system (see page ). 3.
103
Mirrors
Power Mirror Heaters
102
HEATED MIRROR BUTTON
Page 104 of 295

Two seat and outside mirror
positionscanbestoredinseparate
memories. You select a memorized
position by pushing the appropriate
button or using the appropriate
remote transmitter (Driver 1 or
Driver 2).Adjust the outside mirrors f or best
visibility (see page ). Adjust the seat to a comfortable
position (see page ). Turn the ignition switch to the ON
(II) position. You cannot add a
new driving position in the
memory unless the ignition switch
is in the ON (II) position. You can
recall a memorized position with
the ignition switch in any position.
Store a driving position only when
the vehicle is parked.
Your vehicle has a memory feature
f or the driver’s seat and outside
mirror positions.
Press and release the MEMO
button on the driver’s door. You
will hear a beep. Immediately
press and hold one of the memory
buttons (1 or 2) until you hear two
beeps. The indicator in the
memory button will come on. The
current positions of the driver’s
seat and outside mirrors are now
stored.
3.
1.
2.
98
101
CONT INUED
Driving Position Memory System
Storing a Driving Position in
Memory
Inst rument s and Cont rols
103
MEMO BUTTON
MEMORY BUTTONS