2006 Acura TL Owner's Manual

µ
µ Pick the preset button (icon) you
want f or that channel. Press and
hold the button (icon) until you
hear a beep.
Repeat steps 2 and 3 to store the
f irst six channels.
Press the button again.
The other XM band will show.
Store the next six channels using
steps 2 and 3.
Once a channel is stored, simply
press and release the proper preset
button (icon) to tune to it.
Youcanstoreupto12
preset channels using the six preset
buttons or preset icons (on models
with navigation system). Each button
stores one channel f rom the XM1
band and one channel f rom the XM2
band.
To store a channel: Press the button. Either
XM1 or XM2 will show in the
display.
Use the TUNE knob, or the
CATEGORY or SCAN buttons to
tune to a desired channel.
In category mode, only channels
within that category can be selected.
In channel mode, all channels can be
selected.
The SCAN f unction gives
you a sampling of all channels while
in the channel mode. In the category
mode, only the stations within that
category are scanned. To activate
SCAN, press the SCAN button or
touch the SCAN icon on the audio
display (models with navigation
system). The system plays each
channel in numerical order f or 5
seconds, then selects the next
channel. When you hear a channel
you want to continue listening to,
press the button or touch the icon
again. 1.
2.3.
4.
5.
Playing the XMSatellite Radio (U.S. Models)
Preset
SCAN
136

µ
µ µ
µ
µ
µ
CONT INUED
The signal is
currently too
weak. Move the
vehicle to an area
away from tall
buildings, and
with an
unobstructed view
of the southern
horizon.
The selected channel
number does not exist or
isnotpartofyour
subscription, or this
channel has no artist or
title information at this
time.
There is a problem
with the XM
antenna. Please
consult your dealer.
XM is loading the
audio or program
inf ormation.
The channel currently selected is
no longer
broadcasting.
The encryption
code is being
updated. Wait
until the
encryption code is
f ully updated.
Channels 0 and 1
should still work
normally.
Playing the XMSatellite Radio (U.S. Models)
XM Radio Display Messages ‘‘NO SIGNA L ’’
‘‘----’’
‘‘A NT ENNA ’’
‘‘L OA DING’’
‘‘OFF A IR’’
‘‘UPDA T ING’’
Features
137

The XM satellites are in orbit over
the equator; therefore, objects south
of the vehicle may cause satellite
reception interruptions. To help
compensate f or this, ground-based
repeaters are placed in major
metropolitan areas.
Satellite signals are more likely to be
blocked by tall buildings and
mountains the f arther north you
travel from the equator.
Playing the XMSatellite Radio (U.S. Models)
138
Signal may be blocked by
mountains or large obstacles to
the south.Signal weaker in
these areas.
SATELLITE GROUND
REPEATER

Depending on where you drive, you
may experience reception problems.
Interf erence can be caused by any of
these conditions:Driving on the north side of a
large commercial truck on an
east/west road.
Driving in tunnels.
Driving on a road beside a vertical
wall, steep clif f , or hill to the south
of you.
Driving on the lower level of a
multi-tiered road.
Driving on a single lane road
alongside dense trees taller than
50 ft. (15 m) to the south of you. If your XM Radio service has expired
or you purchased your vehicle f rom
a previous owner, you can listen to a
sampling of the broadcasts available
on XM Satellite Radio. With the
ignition switch in the ACCESSORY
(I) or ON (II) position, push the
PWR/VOL knob to turn on the audio
system and press the button.
A variety of music types and styles
will play.
If you decide to purchase XM
satellite radio service, contact XM
Radio at
, or at
1-800-852-9696. You will need to give
them your radio I.D. number and
your credit card number. To get your
radio I.D. number, turn the TUNE knob until ‘‘0’’ appears in the display.
Your I.D. will appear in the display.
After you’ve registered with XM
Radio, keep your audio system in the
Satellite Radio mode while you wait
f or activation. This should take about
30 minutes.
Driving on the north side of an
east/west mountain road.
While waiting f or activation, make
sure your vehicle remains in an open
area with good reception. Once your
audio system is activated, you should
be able to listen to XM radio
broadcasts. XM Radio will continue
to send an activation signal to your
vehicle for at least 12 hours from the
activation request. If the service has
not been activated after 36 hours,
contact XM Radio.
There may be other geographic
situations that could af f ect XM radio
reception.As required by the FCC:
Changes or modif ications not expresslyapproved by the party responsible f orcompliance could void the user’sauthority to operate the equipment.
www.xmradio.com
Receiving Satellite Radio Service
Playing the XMSatellite Radio (U.S. Models)
139

´´
µ
µ
Playing Discs
140
DISC
BUTTON LOAD
BUTTON
SEEK
BUTTONS
EJECT
BUTTON
SEEK
BUTTONS DISC
SLOT
DISC BUTTON
DISC BUTTON
RANDOM BUTTON
DISC BUTTON
RANDOM BUTTON REPEAT BUTTON
SCAN BUTTON DISC
SLOT
CD/DVD BUTTON
U.S. Models (with Navigation System)
Canadian Models (without Navigation System)
REPEAT
BUTTON SCAN
BUTTON LOAD
BUTTON DISC/TAPE
BUTTON AM/FM
BUTTON
PWR/VOL
KNOB PWR/VOL
KNOB
EJECT
BUTTON AM
BUTTON
FM
BUTTON

The disc changer can play these disc
formats:CD
CD-R
DVD-A
DTS
DVD-A discs not meeting DVD
verification standards may not be
playable.
The changer cannot play DVD-V,
DVD-R/RW, MP3, or WMA f ormats.
Some CD-DA and CD-ROM mixed
discs are not playable.
‘‘DTS’’ and ‘‘DTS Digital Surround’’
are registered trademarks of Digital
Theater System, Inc. To load multiple discs in one
operation:
Your vehicle’s audio system has an
in-dash disc changer that holds up to
six discs. You operate this disc
changer with the same controls used
f or the radio. To operate the disc
changer, the ignition switch must be
in the ACCESSORY (I) or ON (II)
position.
With the ignition switch in the
ACCESSORY (I) or ON (II)
position, press and hold the LOAD
button until you hear a beep and
see ‘‘LOAD’’ in the display, then
release the button.
Insert a disc into the slot. Insert it
only about half way; the drive will
pull it in the rest of the way.
When the ‘‘DISC LOAD’’ appears
in the display, insert the next disc
into the slot.
Repeat this until all six positions
are loaded. The system will thenbegin playing the last disc loaded.
If you stop loading discs bef ore all
six positions are f illed, the system
will wait f or 15 seconds, stop the load
operation, and begin playing the last
disc loaded.
If you press the LOAD button while
a disc is playing, the system will stop
playing that disc and start the
loading sequence. It will then play
the disc just loaded. The disc number f or an empty
position is highlighted and the
green load indicator comes on.
When you see ‘‘LOAD’’ in the
display, insert the disc into the slot.
Insert it only about halfway; the
drive will pull it in the rest of the
way. Press and release the LOAD
button.
To load a single disc:
1.
2.
3.
4. 1.
2.
L oading Discs in the Changer
Playing Discs
141
TM
Do not use discs with adhesive labels.
The label can curl up and cause the
disc to jam in the unit.

µ´µ´
µ
µ
´
Select the disc changer by pressing
the DISC/TAPE button (U.S.
models) or CD/DVD button
(Canadian models). The system will
begin playing the last selected disc in
the disc changer. You will see the
disc and track numbers displayed.
To select a dif f erent disc when all six
positions are loaded, use the preset 5
(DISC ) or preset 6 (DISC )
button. Otherwise, press the
corresponding number on the preset
buttons or icons. On models with
navigation system, you can also
touch the appropriate disc icon (1
6) to select a dif f erent disc.
WhenyoupressandholdtheSCAN
button until you see D-SCAN in the
display, or when you touch the DISC
SCAN icon on the audio display
(models with navigation system), the
f irst track of the current disc plays
f or about 10 seconds. You will see D-
SCAN (DISC SCAN) in the display.
To hear the rest of the disc, press
the SCAN button or touch DISC
SCAN again, within 10 seconds. If
you don’t, the system advances to
the next disc, plays about 10 seconds
of it, and continues throughout the
rest of the discs the same way.
When the system reaches the last
disc, DISC SCAN is cancelled, and
the disc you originally had on plays
normally.
Each time you press and release the
SEEK button, the player skips
f orward to the beginning of the next
track. Press and release the SEEK
buttontoskipbackwardtothe
beginning of the current track or to
skip back to previous track.
When you press the SCAN button or
touchtheTRACKSCANicononthe
audio display (models with
navigation system), the f irst track of
the current disc plays f or about 10
seconds. You will see SCAN
(TRACK SCAN) highlighted in the
display. To hear the rest of the track,
press the SCAN button or touch
TRACK SCAN again within 10
seconds. If you don’t, the system
advances to the next track, plays
about 10 seconds of it, and continues
through the rest of the tracks the
same way.
The preset 5 (DISC ) and preset 6
(DISC ) buttons are f or use with
an optional, external CD changer. T o Play a Disc
T o Change T racks Disc Scan
Track Scan
Playing Discs
Features
142

To take the system out of disc mode,
press the AM/FM button (AM or
FMbuttononCanadianmodels),
press the button (U.S.
models), or insert a tape in the tape
player. To return to disc mode, press
the DISC/TAPE button (CD/DVD
buttononCanadianmodels).
When you press the RPT button or
touch the TRACK RPT icon on the
audio display (models with
navigation system), the system
continuously replays the current
track. As a reminder, you will see
REPEAT (TRACK REPEAT) in the
display. To turn this feature off,
press the RPT button, or touch
TRACK REPEAT again.
If you turn the system off while a
disc is playing, either with the PWR/
VOL knob or by turning of f the
ignition switch, the disc will stay in
the drive. When you turn the system
back on, the disc will begin playing
where it lef t of f .
WhenyoupressandholdtheRPT
button until D-RPT is in the display,
or when you touch the DISC RPT
icon on the audio display (models
with navigation system), the system
continuously replays the current disc.
To turn this feature off, press the
RPT button or touch DISC RPT
again. You can also play DVD-As in your
audio system the same way as
playing discs. When you press the RDM button or
touch the TRACK RDM icon
(models with navigation system), the
system plays the tracks of the
current disc in random order. You
will see RDM (TRACK RANDOM)
in the display. To turn this f eature
off, press the RDM button (touch
the TRACK RDM icon) again.
T rack Repeat
Random PlayT o Stop Playing a Disc
Disc Repeat Playing a DVD
Playing Discs
143