2006 Acura MDX Owner's Manual

µµThe SCAN f unction gives
you a sampling of all channels while
in the channel mode. In the category
mode, only the stations within that
category are scanned. To activate
SCAN, press the SCAN button or
touch the SCAN icon on the audio
display (models with navigation
system). The system plays each
channel in numerical order f or a f ew
seconds, then selects the next
channel. When you hear a channel
you want to continue listening to,
press the button or touch the icon
again. Pick the preset button (icon) you
want f or that channel. Press and
hold the button (icon) until you
hear a beep.
Repeat steps 2 and 3 to store the
f irst six channels.
Once a channel is stored, simply
press and release the proper preset
button (icon) to tune to it.
The presets will be lost if your
vehicle’s battery goes dead, is
disconnected, or the radio f use is
removed. Press the XM button again. The
other XM band will show. Store
the next six channels using steps 2
and 3.
Youcanstoreupto12
preset channels using the six preset
buttons or preset icons (on models
with navigation system). Each button
stores one channel f rom the XM1
band and one channel f rom the XM2
band.
To store a channel: Press the XM button. Either XM1
or XM2 will show in the display.
Use the TUNE knob, or the
CATEGORY or SCAN buttons to
tune to a desired channel.
In the category mode, only channels
within that category can be selected.
In the channel mode, all channels
can be selected. 3.
4.
5.
1.
2.
Playing the XMSatellite Radio (U.S. Models)
SCA N Preset
120

The XM satellites are in orbit over
the equator; therefore, objects south
of the vehicle may cause satellite
reception interruptions. To help
compensate f or this, ground-based
repeaters are placed in major
metropolitan areas.
Satellite signals are more likely to be
blocked by tall buildings and
mountains the f arther north you
travel from the equator.
CONT INUED
Playing the XMSatellite Radio (U.S. Models)
Features
121
Signal may be blocked by
mountains or large obstacles to
the south.Signal weaker in
these areas.
SATELLITE GROUND
REPEATER

Depending on where you drive, you
may experience reception problems.
Interf erence can be caused by any of
these conditions:Driving on the south side of an
east/west mountain road.
Driving on the north side of a
large commercial truck on an
east/west road.
Driving in tunnels.
Driving on a road beside a vertical
wall, steep clif f , or hill to the south
of you.
Driving on the lower level of a
multi-tiered road.
Driving on a single lane road
alongside dense trees taller than
50 ft. (15 m) to the south of you. If you decide to purchase XM
satellite radio service, contact XM
Radio at, or at
1-800-852-9696. You will need to give
them your radio I.D. number and
your credit card number. To get your
radio I.D. number, turn the TUNE knob until ‘‘0’’ appears in the display.
Your I.D. will appear in the display.
After you’ve registered with XM
Radio, keep your audio system in the
Satellite Radio mode while you wait
f or activation. This should take about
30 minutes.
If your XM Radio service has expired
or you purchased your vehicle f rom
a previous owner, you can listen to a
sampling of the broadcasts available
on XM Satellite Radio. With the
ignition switch in the ACCESSORY
(I) or ON (II) position, push the
PWR/VOL knob to turn on the audio
system and press the XM button. A
variety of music types and styles will
play. While waiting f or activation, make
sure your vehicle remains in an open
area with good reception. Once your
audio system is activated,
‘‘CATEGORY’’ or ‘‘CH’’ will appear in
the display, and you’ll be able to
listen to XM Radio broadcasts. XM
Radio will continue to send an
activation signal to your vehicle f or
at least 12 hours from the activation
request. If the service has not been
activated after 36 hours, contact XM
Radio.
Cargo may be attached to roof
rack.
There may be other geographic
situations that could af f ect satellite
radio reception.As required by the FCC: Changes or modif ications not expresslyapproved by the party responsible f orcompliance could void the user’sauthority to operate the equipment.
www.xmradio.com
Playing the XMSatellite Radio (U.S. Models)
Receiving Satellite Radio Service
122

Playing a CD
Features
123
U.S. modelsCD BUTTON
REPEAT BUTTON
CD LOAD
BUTTON CD EJECT BUTTON
PWR/VOL
KNOB RANDOM BUTTON
REPEAT BUTTON
CD EJECT BUTTON
RANDOM BUTTON SKIP BUTTONS
CD SLOT
PWR/VOL KNOB
SKIP BUTTONS
CD LOAD BUTTON CD SLOT
(Touring Package With Rear Entertainment System)
(Touring Package Without Rear Entertainment System)
(Premium Package)
CD EJECT BUTTON
PWR/VOL
KNOB CD SLOT
REPEAT BUTTON RANDOM BUTTON SKIP BUTTONS

Playing a CD
124
Canadian modelsCD LOAD BUTTON CD SLOT
RANDOM BUTTON
REPEAT BUTTON
PWR/VOL
KNOB
CD BUTTONCD EJECT BUTTON
CD LOAD BUTTON
REPEAT BUTTON
PWR/VOL
KNOB
SKIP
BUTTONS
CD BUTTON CD EJECT BUTTON
CD SLOT
SKIP
BUTTONS RANDOM BUTTON
(Touring Package With Rear Entertainment System)
(Touring Package Without Rear Entertainment System)

µµ
´µ
µ
´
µPress the eject button to remove the
CD. If you eject the CD, but do not
remove it from the slot, the system
will automatically reload the CD
af ter 15 seconds and put it in pause
mode. To begin playing, press the
CD button. To continuously replay
a track, press and release the RPT
button. You will see RPT/REPEAT
in the display. Press the RPT button
again to turn it off.
This f eature plays the
tracks in random order. To activate
Random Play, press and release the
RDM button. You will see RDM in
the display. Press the RDM button
again to return to normal play.
Press the AM or FM button (AM/
FM button on the U.S. models) to
switch to the radio while a CD is
playing. If you turn the system of f while a CD
is playing, either with the PWR/VOL
knob or by turning off the ignition,
the disc will stay in the drive. When
youturnthesystembackon,theCD
will begin playing where it lef t of f .
To move rapidly within a track, press
andholdthe or skipbutton. Each time you press and
release the skip button the player
skips forward to the beginning of the
next track. Press and release the
skipbuttontoskipbackwardtothe
beginning of the current track. Press
it again to skip to the beginning of
the previous track. You operate the CD player with the
same controls used f or the radio.
The number of the track playing is
shown in the display. The system will
continuously play a CD until you
change modes. With the ignition in the
ACCESSORY (I) or ON (II) position,
insert a CD into the CD slot. The
drive will pull the CD in the rest of
the way and begin to play it.
CONT INUED
Premium model only
To Play a CD
To Stop Playing a CD REPEAT
RANDOM
SK IP
Playing a CD
Features
125

Press and hold the LOAD button
until you hear a beep, then release
the button.
To load only one CD, press and
release the Load button.
On the lef t side of the display, the
CD Loaded indicator f or an empty
position will begin blinking.
When you see LOAD in the
display, insert the disc into the CD
slot. Insert it only about half way,
the drive will pull it in the rest of
the way. You will again see the
dashes in the display as the CD is
loaded.
When LOAD appears again in the
display, insert the next disc into
the CD slot. Do not try to insert a
disc until LOAD appears. You
could damage the audio unit.Repeat this until all six positions
are loaded. The system will then
begin playing the last CD loaded.
If you are not loading CDs into all six
positions, press the LOAD button
again after the last CD has loaded.
The system will begin playing the
last CD loaded.
If you stop loading CDs bef ore all six
positions are f illed, and you do not
press the load button, the system will
wait f or 10 seconds, then stop the
load operation and begin playing the
last CD loaded.
You cannot load and play 3-inch
(8-cm)discsinthissystem. The audio system on your vehicle
has an in-dash CD changer that
holdsuptosixdiscs.
To load CDs or operate CD changer,
the ignition switch must be in the
ACCESSORY (I) or ON (II) position.
1.
2.
3.
4.5.
Touring Model
CD Changer
L oading CDs in the Changer
126

If you do not remove the disc f rom
the slot, the system will reload the
disc af ter 10 seconds and begin
playing it.
To remove a dif f erent CD f rom the
changer,firstselectitwiththe
appropriate preset button. When that
CD begins playing, press the eject
button.In any mode, if you press the eject
button and hold it until you hear a
beep, the system will eject all of the
discs in the changer.
You can also eject discs when the
ignition switch is of f . The disc that
was last selected is ejected f irst. You
can eject up to six discs, one at a
time.
To remove the disc that is currently
playing, press the eject button. You
will see ‘‘EJECT’’ in the display. The
system automatically begins the
Load sequence so you can load
another CD in that position. If you do
not load another CD, af ter 10
seconds the system begins playing
the next disc in the changer. If the
changer is empty, the system selects
the previous mode (AM, FM, or XM
radio).
If you press the Eject button while
listening to the radio, XM radio, or
with the audio system turned off, the
disc that was last selected is ejected.
Af ter that disc is ejected, pressing
the Eject button again will eject the
next disc in the numerical order. By
doing this six times, you can remove
all the CDs f rom the changer.
If you press the LOAD button while
a disc is playing, the system will stop
playing that disc and start the
loading sequence. It will then play
the disc just loaded.
You can also load a CD into an empty
position while a CD is playing by
pressing the appropriate preset
button. Select an empty position (the
CD loaded indicator is of f ), and press
the preset button for that position (1
to 6). The system will stop playing
the current CD and start the loading
sequence. It will then play the CD
just loaded. Removing CDs f rom the Changer
CD Changer
Features
127