2006 ACURA CSX weight

(#' '

) (#' '

)
DTC 24-11:
DTC 24-12:
DTC 24-13:
DTC 24-14:DTC 26-11:
DTC 26-12:
DTC 26-13:
DTC 26-14:
24-18024-180SRS
DTC Troubleshooting (cont’d)
Short to Power in the Front
Passenger’s Weight Sensor (front outer side)
Power Circuit
Short to Ground in the Front
Passenger’s Weight Sensor (front outer side)
Power Circuit
Open in the Front Passenger’s
Weight Sensor (front outer side) Output
Circuit
Short to Ground in the Front
Passenger’s Weight Sensor (front outer side)
Output Circuit Short to Power in the Front
Passenger’s Weight Sensor (rear outer side)
Power Circuit
Short to Ground in the Front
Passenger’s Weight Sensor (rear outer side)
Power Circuit
Open in the Front Passenger’s
Weight Sensor (rear outer side) Output
Circuit
Short to Ground in the Front
Passenger’s Weight Sensor (rear outer side)
Output Circuit
NOTE: Only read DTCs from the SRS menu, not from
the SWS menus unless instructed to check SWS DTCs.
SWS (ODS unit) DTCs are subcodes of SRS unit DTCs.
Only troubleshoot the corresponding SRS DTCs.
Do the troubleshooting for SRS unit DTC 82-24
(see page 24-159). NOTE: Only read DTCs from the SRS menu, not from
the SWS menus unless instructed to check SWS DTCs.
SWS (ODS unit) DTCs are subcodes of SRS unit DTCs.
Only troubleshoot the corresponding SRS DTCs.
Do the troubleshooting for SRS unit DTC 83-26
(see page 24-163).
08/08/21 14:00:58 61SNR030_240_0180
ProCarManuals.com
DYNOMITE -2009-

(#' '
-)(#')µ
µ
µ
µ
DTC 15-3x:
DTC 17-3x:
DTC 25-3x:
DTC 27-3x: SRS indicator does not come on
YES
NO
YES
NO
24-18124-181
Symptom Troubleshooting
No Signal From the Front Inner
Side Front Passenger’s Weight Sensor
No Signal From the Rear Inner
Side Front Passenger’s Weight Sensor
No Signal From the Front Outer
Side Front Passenger’s Weight Sensor
No Signal From the Rear Outer
Side Front Passenger’s Weight Sensor
NOTE: Only read DTCs from the SRS menu, not from
the SWS menus unless instructed to check SWS DTCs.
SWS (ODS unit) DTCs are subcodes of SRS unit DTCs.
Only troubleshoot the corresponding SRS DTCs.
Do the troubleshooting for SRS unit DTC 82-15, 82-17,
83-25, and 83-27 (see page 24-155). 1. Turn the ignition switch to LOCK (0), then wait for
10 seconds.
2. Turn the ignition switch to ON (II), and check that the SRS indicator comes on for about 6 seconds
and then goes off.
Intermittent failure, system is OK at this
time.
Go to step 3.
3. Connect the HDS to the data link connector (DLC) (see page 24-22).
4. Make sure the HDS communicates with the vehicle and the SRS unit. If it does not communicate,
troubleshoot the DLC circuit (see page 11-204).
5. Do the gauge control module self-diagnostic function (see page 22-241).
Faulty SRS unit; replace the SRS unit
(see page 24-203).
Faulty gauge control module (tach); replace
the gauge control module (tach) (see page 22-277).
Does the SRS indicators come on?
Does t he SRS i nd i cat or come on?
08/08/21 14:01:52 61SNR030_240_0181
ProCarManuals.com
DYNOMITE -2009-

(#' '
-)(#')µ
µ
µ
µ
DTC 15-3x:
DTC 17-3x:
DTC 25-3x:
DTC 27-3x: SRS indicator does not come on
YES
NO
YES
NO
24-18124-181
Symptom Troubleshooting
No Signal From the Front Inner
Side Front Passenger’s Weight Sensor
No Signal From the Rear Inner
Side Front Passenger’s Weight Sensor
No Signal From the Front Outer
Side Front Passenger’s Weight Sensor
No Signal From the Rear Outer
Side Front Passenger’s Weight Sensor
NOTE: Only read DTCs from the SRS menu, not from
the SWS menus unless instructed to check SWS DTCs.
SWS (ODS unit) DTCs are subcodes of SRS unit DTCs.
Only troubleshoot the corresponding SRS DTCs.
Do the troubleshooting for SRS unit DTC 82-15, 82-17,
83-25, and 83-27 (see page 24-155). 1. Turn the ignition switch to LOCK (0), then wait for
10 seconds.
2. Turn the ignition switch to ON (II), and check that the SRS indicator comes on for about 6 seconds
and then goes off.
Intermittent failure, system is OK at this
time.
Go to step 3.
3. Connect the HDS to the data link connector (DLC) (see page 24-22).
4. Make sure the HDS communicates with the vehicle and the SRS unit. If it does not communicate,
troubleshoot the DLC circuit (see page 11-204).
5. Do the gauge control module self-diagnostic function (see page 22-241).
Faulty SRS unit; replace the SRS unit
(see page 24-203).
Faulty gauge control module (tach); replace
the gauge control module (tach) (see page 22-277).
Does the SRS indicators come on?
Does t he SRS i nd i cat or come on?
08/08/21 14:01:52 61SNR030_240_0181
ProCarManuals.com
DYNOMITE -2009-

(#')
µ
µ µ
µ
µ
µ
Passenger’s airbag cutoff indicator stays on
or comes on suddenly
YES
NO YES
NO
YES
NO
24-184SRS
Symptom Troubleshooting (cont’d)
NOTE: Under the following conditions, the passenger’s
airbag cutoff indicator stays on or comes on suddenly.
 No one is sitting the front passenger’s seat, but there is an object on the seat more than 5 kg (11 lbs).
 The seat belt is buckled, but no one is sitting on the front passenger’s seat.
 Someone who is less than 30 kg (66 lbs) is sitting on the front passenger’s seat.
 Someone who is more than 30 kg (66 lbs) but is supporting some of their body weight on their legs,
feet, arms, or hands.
1. Check for these items, then recheck the passenger’s airbag cutoff indicator.
 The front passenger’s seat is/was installed correctly.
 Nothing is/was on the front passenger’s seat.
 Nothing is/was under the front passenger’s seat.
 Nothing is/was in the front passenger’s seat-back pocket.
 Whoever was sitting on the passenger’s seat was sitting in the proper sitting position.
Go to step 2.
Troubleshooting is complete.
2. Connect the HDS to the data link connector (DLC) (see page 24-22).
3. Turn the ignition switch to ON (II).
4. Make sure the HDS communicates with the vehicle and the SRS unit. If it does not communicate,
troubleshoot the DLC circuit (see page 11- 204).5. Select the INSPECTION menu on the HDS, then
select AFTER REPLACING FRONT PASSENGER’S
SEAT COMPONENT(S), and follow the prompts.
Go to step 6.
Troubleshooting is complete.
6. Select the INSPECTION menu on the HDS, then select AFTER A VEHICLE COLLISION, and follow
the prompts.
Replace the SRS unit (see page 24-203). If the
problem is still present, replace the ODS unit
(see page 24-209), and then if the problem is still
present, replace the passenger’s weight sensors
(see page 24-207).
Troubleshooting is complete.
Does the passenger’s airbag cutof f indicator stayon? Does t he passenger ’ s ai r bag cut of f i nd i cat or st ay
on?
Does t he passenger ’ s ai r bag cut of f i nd i cat or st ayon?
08/08/21 14:01:53 61SNR030_240_0184
ProCarManuals.com
DYNOMITE -2009-




(#' )
Special Tools Required
Removal
Installation
24-207
Front Passenger’s Weight Sensor Replacement
A
E B
D
D
C
BUSHING
(BLACK) SPRING WASHER
WASHER
(SILVER)
COLLAR
(BLACK)
BUSHING
(WHITE)
SPRING WASHER
WASHER (SILVER) COLLAR
(SILVER)
Pin driver, 3.5 mm 07744-0010300
NOTE: Removal of the front passenger’s weight sensors
must be done according to Precautions and Procedures
(see page 24-13).
1. Do the battery terminal disconnection procedure (see page 22-68), then wait at least 3 minutes
before starting work.
2. Remove the front passenger’s seat assembly (see page 20-118).
3. Remove the cushion cover/pad from the seat cushion frame (see page 20-127).
4. Using a TORX E18 socket, remove the TORX nuts (A) attaching the seat track (B) to the seat slide
assembly including all four front passenger’s
weight sensors (C).
5. Disconnect the sensor connectors (D) from the seat weight sensors (E), then remove the front
passenger’s weight sensors. NOTE: Be sure to install the wire harness so they are
not pinched or interfering with other parts.
1. Install the new front passenger’s seat slide assembly including all four front passenger’s
weight sensors with under the seat track.
2. Apply multipurpose grease to the spring washer and bushing.
(cont’d)
08/08/21 14:02:02 61SNR030_240_0207
ProCarManuals.com
DYNOMITE -2009-


Î
24-208SRS
Front Passenger’s Weight Sensor Replacement (cont’d)
A
42 N·m
(4.2 kgf·m, 30 lbf·ft)
07744-0010300
MORE THAN
4mm(0.2in.)
A
B B B
B
3. Insert the special tool into the hole in the cushion frame to position the spring washers, then tighten
the TORX nuts (A). Begin with , and tighten them
in crisscross pattern in two or more steps.
4. Using the pin driver to position the spring washer’s, torque the TORX nuts in the sequence shown in
two or more steps. 5. Make sure the gap between the spring washer (A)
and the seat track (B) is more than 4 mm (0.2 in.) as
shown.
6. Reassemble the front passenger’s seat cushion cover/pad (see page 20-127).
7. Reinstall the front passenger’s seat (see page 20-118).
8. Do the battery terminal reconnection procedure (see page 22-68).
9. Calibrate the ODS unit (see page 24-27).
10. Clear any DTCs (see page 24-23).
11. Confirm proper operation: Turn the ignition switch to ON (II); the SRS indicator should come on for
about 6 seconds and then go off.
08/08/21 14:02:03 61SNR030_240_0208
ProCarManuals.com
DYNOMITE -2009-