2006 ACURA CSX weight



(#'
 )

S

pecial Tools Required
20-127
Front Seat Cushion Cover Replacement
Fastener Locations
AB
C
:Screw,2
BFas

tener Locations
:Screw,1
C:Clip,1
AB
B
A
Passenger’s seat
Driver’s seat C
KTC trim tool set SOJATP2014
SRS components are located in this area. Review the
S
RS component locations (see page 24-11) and the
precautions and procedures (see page 24-13) before
doing repairs or service.
 Check the operation of the driver’s seat position sensor after any of these actions (see page 24-29):
– Driver’s seat position sensor replacement
– Cover plate (front side of driver’s seat slide rail) replacement
 Calibrate the ODS unit after any of these actions (see page 24-27):
– Front passenger’s seat replacement (including any seat components)
– Replacement of the front seat weight sensors
– After a vehicle collision
NOTE:  Use the appropriate tool from the KTC trim tool set to avoid damage when removing components.
 Take care not to tear or damage the seat covers.
 Put on gloves to protect your hands.
1. Remove the front seat (see page 20-118).
2. Remove the front seat belt buckle (see page 24-6).
3. Pull back the cap (A) to release the hooks (B), and remove the screws, then remove the height
adjuster handle (C). 4.

Remove the recline cover (A).
–1 Remove the recline knob (B) and the screw.
–2 Gently pull out the cover, then detach the clip, and release the hooks (C).
(cont’d)
08/08/21 15:03:59 61SNR030_200_0129
ProCarManuals.com
DYNOMITE -2009-


Î
(#'



") ’07-08 models
’09 model
22-176Exterior Lights
Fog Light Adjustment
A
A
Before adjusting the fog lights:  Park the vehicle on a level surface.
 Make sure the tire pressures are correct.
 The driver or someone who weights the same should sit in the driver’s seat.
Adjust the fog lights to local requirements by turning
the adjuster (A).
08/08/21 14:27:02 61SNR030_220_0178
ProCarManuals.com
DYNOMITE -2009-

(#'
/)
Restraints
Restraints
Seat Belts
SRS (Supplemental Restraint System)
................................................................ ................................................................
Special Tools . 24-2
..............................................................................
.......................................
..................................................................... ........................................
......................................
.......................................
.....................................................................
Component Location Index . 24-3
Front Seat Belt Replacement . 24-4
Rear Seat Belt Replacement . 24-7
Inspection . 24-9
.............................................................................. ......................
.................................................
................................................... ......................................... .......
....................................... ..............................
.....................................................
............................................................ ..........................................................................................
.............................................................. .........................................................
........................................... ..............................
..................................
.............................................
................................................ ................................
.............................. ......
............................................... .........................................
......................
........................................
...................................... ......................
.................................................
................................................... ......................................... .......
....................................... ..............................
.....................................................
............................................................ ..........................................................................................
.............................................................. .........................................................
........................................... ..............................
..................................
.............................................
................................................ ................................
.............................. ......
............................................... .........................................
......................
Component Location Index . 24-11
Precautions and Procedures . 24-13
General Troubleshooting Information . 24-22
ODS Unit Initialization . 24-26
ODS Unit Calibration . 24-27
ODS Unit Operation Check . 24-28
Driver’s Seat Position Sensor Operation Check . 24-29
DTC Troubleshooting Index . 24-30
Symptom Troubleshooting Index . 24-34
System Description . 24-35
Circuit Diagram . 24-40
DTC Troubleshooting . 24-48
Symptom Troubleshooting . 24-181
Component Replacement/Inspection After
Deployment . 24-185
Driver’s Airbag Replacement . 24-188
Front Passenger’s Airbag Replacement . 24-189
Side Airbag Replacement . 24-191
Side Curtain Airbag Replacement . 24-192
Airbag and Tensioner Disposal . 24-196
Cable Reel Replacement . 24-200
SRS Unit Replacement . 24-203
Side Impact Sensor (First) Replacement . 24-204
Side Impact Sensor (Second) Replacement . 24-205
Rear Safing Sensor Replacement . 24-206
Front Passenger’s Weight Sensor Replacement . 24-207
ODS Unit Replacement . 24-209
Front Impact Sensor Replacement . 24-210
Driver’s Seat Position Sensor Replacement . 24-211
Passenger’s Airbag Cutoff Indicator Illumination Bulb Test/Replacement . 24-212
08/08/21 13:54:05 61SNR030_240_0001
ProCarManuals.com
DYNOMITE -2009-

Î
(#')
24-11
SRS
Component Location Index
SRS INDICATOR
SIDE AIRBAG
CUTOFF INDICATOR
CABLE REEL
DRIVER’S AIRBAG
FRONT PASSENGER’S AIRBAG
PASSENGER’S AIRBAG CUTOFF INDICATOR
SRS UNIT OPDS SENSOR/SEAT-BACK
FRONT PASSENGER’S
SIDE AIRBAG
FRONT PASSENGER’S
SEAT BELT TENSIONER RIGHT SIDE
IMPACT SENSOR
(FIRST)
ODS UNIT
FRONT PASSENGER’S WEIGHT SENSORS
DRIVER’S SEAT BELT TENSIONER
LEFT SIDE IMPACT SENSOR (FIRST)
DRIVER’S SEAT POSITION SENSOR
DRIVER’S SIDE AIRBAG
DATA LINK
CONNECTOR (DLC) MEMORY ERASE
SIGNAL (MES)
CONNECTOR (2P)
(YELLOW)
FRONT PASSENGER’S SEAT BELT
BUCKLE TENSIONER
DRIVER’S SEAT BELT BUCKLE TENSIONER
(cont’d)
Troubleshooting, page 24-181
Troubleshooting, page 24-183
Replacement, page 24-200
Replacement, page 24-188
Disposal, page 24-196
Replacement, page 24-189
Disposal, page 24-196
Troubleshooting, page 24-184
Bulb Test/Replacement, page 24-212
Replacement, page 24-203 Replacement, page 20-122
Replacement,page 24-191
Disposal, page 24-196
Replacement, page 24-4
Disposal,
page 24-196 Replacement,
page 24-204
Initialization, page 24-26
Calibration, page 24-27
Operation Check, page 24-28
Replacement, page 24-209
Replacement, page 24-207
Replacement, page 24-4
Disposal, page 24-196
Replacement, page 24-204
Operation Check, page 24-29
Replacement, page 24-211
Replacement, page 24-188
Disposal, page 24-196Replacement, page 24-6
Replacement, page 24-6
08/08/21 13:54:16 61SNR030_240_0011
ProCarManuals.com
DYNOMITE -2009-


SRS Unit, Front and Side Impact Sensors,
Driver’s Seat Position Sensor, Front
Passenger’s Weight Sensors and, Rear
Safing Sensor
24-15
NOTE: Some systems store data in memory that is lost
when the battery is disconnected. Before disconnecting
the battery, refer to Battery Terminal Disconnection and
Reconnection (see page 22-68).
 Turn the ignition switch to LOCK (0), disconnect the negative cable from the battery, then wait at least 3
minutes before starting installation or replacement of
the SRS unit, or disconnecting the connectors from
the SRS unit.
 Be careful not to bump or impact the SRS unit, the front impact sensors, the side impact sensors, or the
rear safing sensor whenever the ignition switch is in
ON (II), or for at least 3 minutes after the ignition
switch is turned to LOCK (0).
 During installation or replacement, be careful not to bump (by impact wrench, hammer, etc.) the area
around the SRS unit, the front impact sensors, the
side impact sensors, or the rear safing sensor. The
airbags could accidentally deploy and cause damage
or injury.  After a collision where the front airbag, the side
airbag, or a the seat belt tensioner, the seat belt
buckle tensioner deployed, go to Component
Replacement/Inspection after Deployment (see page
24-185). After a collision where an airbag did not
deploy, inspect for any damage or any deformation
on the SRS unit, the front impact sensors, the side
impact sensors, or the rear safing sensor. If there is
any damage, replace the SRS unit and/or the sensors.
 Do not disassemble the SRS unit, front impact sensors, side impact sensors, driver’s seat position
sensor, front passenger’s weight sensors or rear
safing sensor.
 Always install the SRS unit, driver’s seat position sensor, and all impact sensors and the rear safing
sensor securely with new TORX bolts torqued to 9.8
N·m (1.0 kgf·m, 7.2 lbf·ft).
 Do not spill water or oil on the SRS unit or the any of the sensors, and keep them away from dust.
(cont’d)
08/08/21 13:54:19 61SNR030_240_0015
ProCarManuals.com
DYNOMITE -2009-


Checking Front Passenger’s Weight Sensors
After a Vehicle Collision
24-25
A
10. Shake the related wire harnesses and theconnectors, and look for loose connections, poor
pinfits, and poor grounds.
11. Take a test-drive (quick acceleration, quick braking, and cornering), turn the steering wheel fully left
and right, and hold it there for 5 to 10 seconds. If
the problem recurs, the SRS indicator will come on.
12. If you cannot duplicate the concern, ask the client about the conditions when it occurred, or ask the
client to demonstrate the concern.
13. If you cannot duplicate the intermittent failure, the system is OK at this time. 1. Position the front passenger’s seat to the rearmost
position, adjust the seat-back to the forwardmost
position. Do not move it from this position.
2. Drive the vehicle, accelerate to 20 mph (36 km/h), then stop on level ground.
3. Make sure the ignition switch is in LOCK (0).
4. Connect the HDS to the data link connector (DLC) (A).
5. Turn the ignition switch to ON (II).
6. Make sure the HDS communicates with the vehicle and the SRS unit. If does not communicate,
troubleshoot the DLC circuit (see page 11-204).
7. From the SRS inspection menu, select Seat Weight Sensor, then Misc test, then SEAT OUTPUT CHK
and follow the prompts until the front passenger’s
weight sensor operation check is complete.
08/08/21 13:54:22 61SNR030_240_0025
ProCarManuals.com
DYNOMITE -2009-

(#'
)
24-27
ODS Unit Calibration
A
When you replace the SRS unit, front passenger’s
weight sensors or ODS unit, calibrate the ODS unit.
While calibrating the ODS unit, observe these
precautions: Make sure all components of the front passenger’s seat are correctly installed.
 Make sure nothing is on or under the front passenger’s seat.
 Make sure there is nothing in the front passenger’s seat-back pocket.
 Keep the windows and moonroof closed.
 Do all calibration procedures except, test-driving, in the service bay.
 Make sure the vehicle is on level gr ound.
 Keep the A/C and the heater off.
 Do not touch the front passenger’s seat during calibration, unless you are prompted to or when you
have completed the calibration.
 Do not expose the front passenger’s seat to sudden temperature changes.
1. Position the front passenger’s seat to the rearmost position, and adjust the seat-back to the
forwardmost position. Do not move the seat from
these positions.
2. Make sure the ignition switch is in LOCK (0).
3. Connect the HDS to the data link connector (DLC) (A).
4. Turn the ignition switch to ON (II).
5. Make sure the HDS communicates with the vehicle and the SRS unit. If it does not communicate,
troubleshoot the DLC circuit (see page 11- 204).6. Drive the vehicle, and accelerate to 20 mph
(36 km/h), then stop on level ground.
7. From the Main Menu, select SRS, then Calibration, then Misc Test, then select SWS INITIALIZATION,
and follow the prompts until the calibration is
complete.
08/08/21 13:54:23 61SNR030_240_0027
ProCarManuals.com
DYNOMITE -2009-


(#'
")
Pre-operation Check Set-up After Replacing Front Passenger’s Seat
Component(s)
24-28SRS
ODS Unit Operation Check
A
Check the ODS operation after any of these actions.
 Replacement of front passenger’s seat component(s) (except ODS unit and/or weight sensors)
 After a vehicle collision
 SRS unit replacement
 Make sure all the components of the front passenger’s seat are correctly installed.
 Position the front passenger’s seat to the rearmost position.
 Adjust the seat-back to the forwardmost position.
 Do not move the seat from this position.
 Make sure nothing is on or under the front passenger’s seat.
 Make sure there is nothing in the front passenger’s seat-back pocket.
 Keep the windows and moonroof closed.
 Do all calibration procedures, except test-driving, in the service bay.
 Make sure the vehicle is on level gr ound.
 Turn the heater and the A/C off.
 Do not touch the front passenger’s seat during the calibration, unless you are prompted to or until you
have completed the operation check.
 Do not expose the front passenger’s seat to sudden temperature changes.
 Make sure all aftermarket devices such as amplifiers, fluorescent lights, air purifies, CB or HAM radios, etc.
are turned off. 1. Make sure the ignition switch is in LOCK (0).
2. Connect the HDS to the data link connector (DLC)
(A).
3. Turn the ignition switch to ON (II).
4. Make sure the HDS communicates with the vehicle and the SRS unit. If it does not communicate,
troubleshoot the DLC circuit (see page 11-204).
5. Drive the vehicle, accelerate to 20 mph (36 km/h), then stop on level ground.
6. From the HDS Main Menu, select SRS, then Inspection. In the HDS Inspection Menu, select
SEAT OUTPUT CHK and follow the prompts until
the ODS unit operation check is complete.
08/08/21 13:54:23 61SNR030_240_0028
ProCarManuals.com
DYNOMITE -2009-