2006 ACURA CSX battery


(#' 
'
-)
µ
µ
µ
µ
DTC A2-1x (‘‘x’’ can be 0 thru 9 or A thru F):
YES
NO
YES
NO
24-173
SRS UNIT CONNECTOR A (28P)
Faulty Power Supply (VB Line)
NOTE: Before doing this troubleshooting procedure,
review SRS Precautions and Procedures (see page
24-13), General Troubleshooting Information (see page
24-22), and Battery Terminal Disconnection and
Reconnection (see page 22-68).1. Check the No. 11 (10 A) fuse in the under-dash fuse/relay box.
Go to step 2.
Replace the fuse, then turn the ignition switch
ON (II). If the fuse blows again, check for a short to
ground in the under-dash fuse/relay box No. 11
(10 A) fuse line, in the dashboard wire harness;
replace the under-dash fuse/relay box (see page
22-66), then clear the DTC.
2. Turn the ignition switch to LOCK (0). Disconnect the negative cable from the battery, then wait at least 3
minutes.
3. Disconnect SRS unit connector A (28P) from the SRS unit (see step 9 on page 24-21).
4. Reconnect the negative cable to the battery. 5. Connect a voltmeter between SRS unit connector A
(28P) terminal No. 18 and body ground. Turn the
ignition switch to ON (II), and measure the voltage.
There should be battery voltage when the ignition
switch is on.
Faulty SRS unit or poor contact at SRS unit
connector A (28P) and the SRS unit; check the
connection. If the connection is OK, replace the
SRS unit (see page 24-203).
Go to step 6.
(cont’d)
Wire side of female terminals
IsthefuseOK? Is there battery voltage?
08/08/21 14:00:56 61SNR030_240_0173
ProCarManuals.com
DYNOMITE -2009-

Î
(#')
µ
µ
µ
µ
µ
µ µ
µ
µ
µ
SRS indicator stays on, but no DTCs are
stored
YES
NO
YES
NO
YES
NO YES
NO
YES
NO
24-182
SRS
Symptom Troubleshooting (cont’d)
SRS UNIT CONNECTOR A (28P)
NOTE: Before doing this troubleshooting procedure,
review SRS Precautions and Procedures (see page
24-13), General Troubleshooting Information (see page
24-22), and Battery Terminal Disconnection and
Reconnection (see page 22-68).
1. Connect the HDS to the data link connector (DLC) (see page 24-22).
2. Turn the ignition switch to ON (II).
3. Make sure the HDS communicates with the vehicle and the SRS unit. If it does not communicate,
troubleshoot the DLC circuit (see page 11- 204).
4. Select Body Electrical status with the HDS.
5. Check for DTCs in the Gauge Menu with the HDS.
Go to the troubleshooting for DTC B 1187
(see page 22-265).
Go to step 6.
6. Check that the HDS communicates with the SRS unit.
Go to step 7.
If the HDS does not communicate with the
SRS unit, check for power and ground at the SRS
unit connector A (28P). If power and grounds are ok,
replace the SRS unit (see page 24-203).
7. From the HDS System Menu, select SRS, then SRS in Mode Menu, PARAMETER INFORMATION, then
SCS, MES, Indicator. Read the current status of the
SRS indicator.
Faulty SRS unit; replace the SRS unit
(see page 24-203).
Go to step 8. 8. Do the gauge self-diagnostic test (see page 22-241).
Go to step 9.
Faulty gauge control module (tach); replace
the gauge control module (tach) (see page 22-277).
9. Turn the ignition switch to LOCK (0). Disconnect the negative cable from the battery, and wait at least 3
minutes.
10. Disconnect the SRS unit connector A (28P) from the SRS unit (see step 8 on page 24-21).
11. Measure the resistance between SRS unit connector A (28P) terminal No. 5 and body ground.
There should be an open circuit or at least 1 M .
Faulty SRS unit or poor connection at SRS
unit connector A (28P) and the SRS unit. Check the
connection between the connector and the SRS
unit. If the connection is OK, replace the SRS unit
(see page 24-203).
Short in the dashboard wire harness; replace
the dashboard wire harness.
Wire side of female terminals
I s DT C B1187 i nd i cat ed ?
Does the HDS communicate with the SRS unit?
Is the status ON? Does the SRS indicator f lash?
Is the resistance as specif ied?
08/08/21 14:01:53 61SNR030_240_0182
ProCarManuals.com
DYNOMITE -2009-

Î
 
Î
(#'
 )
Removal Installation
24-188SRS
Driver’s Airbag Replacement
A
B
A
B
C
9.8 N·m (1.0 kgf·m, 7.2 lbf·ft)
A
B
A B
NOTE: If replacing the driver’s airbag after deployment,
refer to Component Replacement/Inspection After
Deployment (see page 24-185) for a complete list of
other parts that must also be replaced.
1. Do the battery terminal disconnection procedure (see page 22-68), then wait at least 3 minutes
before starting work.
2. Remove the access panel (A) from the steering wheel, then disconnect the driver’s airbag 4P
connector (B) from the cable reel.
3. Using a TORX T30 bit, remove the two TORX bolts (A) and discard them.
4. Disconnect the horn switch connector (1P), then remove the driver’s airbag (B). 1. Connect the horn switch connector (1P) (A) to the
driver’s airbag.
2. Place the driver’s airbag (B) in the steering wheel, and secure it with new TORX bolts (C).
3. Connect the driver’s airbag 4P connector (A) to the cable reel 4P connector, then install the access
panel (B) on the steering wheel.
4. Do the battery terminal reconnection procedure (see page 22-68).
5. Clear any DTCs (see page 24-23).
6. After installing the airbag, confirm proper system operation:
 Turn the ignition switch to ON (II); the SRS indicator should come on for about 6 seconds
andthengooff.
 Make sure the horn works.
Replace.
08/08/21 14:01:55 61SNR030_240_0188
ProCarManuals.com
DYNOMITE -2009-




(#'
 )
Removal
24-189
Front Passenger’s Airbag Replacement
A A
B
CC
NOTE: If replacing the front passenger’s airbag after
deployment, refer to Component Replacement/
Inspection After Deployment (see page 24-185) for a
complete list of other parts that must also be replaced.1. Do the battery terminal disconnection procedure (see page 22-68), then wait at least 3 minutes
before starting work.
2. Remove the glove box (see page 20-104).
3. Disconnect the front passenger’s airbag 4P connector (A) from the dashboard wire harness.
4. Remove the center panel:  Navigation unit, with navigation system.– ’06-08 models (see page 23-256)
– ’09 model (see page 23-355)
 Audio unit, without navigation system. – ’06-08 models (see page 23-80)
– ’09 model (see page 23-155) 5. Remove the three mounting nuts (A) from the
bracket. Cover the front passenger’s lid and
dashboard with a cloth, and pry carefully with a
screwdriver to lift the front passenger’s airbag
assembly (B) out of the dashboard. If you replacing
only the front passenger’s lid, go to step 6.
NOTE: The front passenger’s lid has pawls (C) on
each side which attach it to the dashboard.
(cont’d)
08/08/21 14:01:55 61SNR030_240_0189
ProCarManuals.com
DYNOMITE -2009-




Installation
24-190SRS
Front Passenger’s Airbag Replacement (cont’d)
A
A
B
A
B B
9.8 N·m
(1.0 kgf·m, 7.2 lbf·ft)
A
A
6. Cut the four parts (A) of the front passenger’s lid (B)as shown, and remove the front passenger’s airbag.
NOTE: Always replace the front passenger’s lid whenever you remove the front passenger’s
airbag from the lid.
 Replace the front passenger’s airbag if the airbag mounting hooks or its housing is damaged.
7. Insert the hooks (A) of the front passenger’s airbag housing into the new front passenger’s lid, then
insert the other hooks (B) into the lid.
NOTE: Make sure there are no objects between the airbag and the front passenger’s lid.
 Make sure the airbag is fully seated, and make sure the front passenger’s lid is not deformed or
damaged after the airbag is in place.
 Do not use tools when detaching the front passenger’s airbag in order to protect it. 1. Place the front passenger’s airbag assembly (A)
into the dashboard. Tighten the front passenger’s
airbag mounting nuts (B).
2. Connect the front passenger’s airbag 4P connector (A) to dashboard wire harness, then reinstall the
glove box and center panel.
3. Do the battery terminal reconnection procedure (see page 22-68).
4. Clear any DTC (see page 24-23).
5. After installing the airbag, confirm proper system operation: Turn the ignition switch to ON (II); the
SRS indicator should come on for about 6 seconds
andthengooff.
08/08/21 14:01:56 61SNR030_240_0190
ProCarManuals.com
DYNOMITE -2009-


Î
(#'
 )
Removal Installation
24-191
Side Airbag Replacement
AB
A
B
6.3 N·m
(0.64 kgf·m, 4.65 lbf·ft)
NOTE: If replacing the side airbag after deployment,
refer to Component Replacement/Inspection After
Deployment (see page 24-185) for a complete list of
other parts that must also be replaced. 1. Do the battery terminal disconnection procedure (see page 22-68), then wait at least 3 minutes
before starting work.
2. Remove the seat assembly (see page 20-118) and seat-back cover (see page 20-123).
3. Remove the mounting screws (A) and the side airbag (B). NOTE:
 If the side airbag lid is secured by tape, remove the tape.
 Do not open the lid of the side airbag cover.
 Use new mounting screws tightened to the specified torque. When you replace a side airbag, make sure
that the seat-back cover is installed properly.
Improper installation may prevent proper
deployment.
 Be sure to install the harness wires so that they are not pinched or interfering with other parts.
1. Place the side airbag on the seat-back frame (A). Install new side airbag mounting screws (B).
2. Install the seat-back cover in the reverse order of removal (see page 20-123).
3. Install the seat assembly (see page 20-118).
4. Move the front seat and the seat-back through their full ranges of movement, making sure the harness
wires are not pinched or interfering with other parts.
5. Do the battery terminal reconnection procedure (see page 22-68).
6. Clear any DTCs (see page 24-23).
7. After installing the side airbag, confirm proper system operation: Turn the ignition switch to ON
(II); the SRS indicator should come on for about
6 seconds and then go off.
Replace.
08/08/21 14:01:56 61SNR030_240_0191
ProCarManuals.com
DYNOMITE -2009-


(#' )
Removal
24-192SRS
Side Curtain Airbag Replacement
A
NOTE: If replacing the side curtain airbag after deployment, refer to Component Replacement/Inspection After
Deployment (see page 24-185) for a complete list of other parts that must also be replaced.
NOTE:
 Review the interior trim replacement procedure before doing repair or service (see page 20-69).
 Removal of the side curtain airbag must be done according to the Precautions and Procedures (see page 24-13).
 The side curtain airbag system consists of the side curtain airbag module, including the roof trim, front grab handle, all grab handle brackets and shielding protector. After the side curtain airbag has been deployed, replace these parts
(see page 24-185).
1. Do the battery terminal disconnection procedure (see page 22-68), then wait at least 3 minutes before starting work.
2. Remove the headliner (see page 20-84).
3. Disconnect the side curtain airbag 2P connector (A) from the floor wire harness.
Left side shown; right side is similar.
08/08/21 14:01:56 61SNR030_240_0192
ProCarManuals.com
DYNOMITE -2009-


24-195
A
2. Connect the side curtain airbag 2P connector (A) to the floor wire harness.
3. Do the battery terminal reconnection procedure (see page 22-68).
4. Clear any DTCs (see page 24-23).
5. After installing the side curtain airbag, confirm proper system operation: Turn the ignition switch to ON (II); theSRS indicator should come on for about 6 seconds and then go off.
6. Install all removed parts.
7. Confirm proper headliner/pillar trim overlap (see page 24-187).
Left side shown; right side is similar.
08/08/21 14:01:57 61SNR030_240_0195
ProCarManuals.com
DYNOMITE -2009-