(#'
'
)
µ
µ
µ
µ µ
µ
DTC 82-14:
YES
NO
YES
NO YES
NO
24-151
A
A
No Signal from the Front
Passenger’s Weight Sensor (front inner side)
NOTE: Before doing this troubleshooting procedure,
review SRS Precautions and Procedures (see page
24-13) and General Troubleshooting Information
(see page 24-22).
1. Clear the DTC memory (see page 24-23).
2. Read the DTC (see page 24-22).
Go to step 3.
Intermittent failure, system is OK at this time.
Go to Troubleshooting Intermittent Failures
(see page 24-24).
3. From the SRS INSPECTION menu on the HDS, select SWS DTC CHECK.
DTC 14-11: Short to power in the ODS unit harness; replace the ODS unit harness, then clear
the DTC.
DTC 14-12: Go to step 4.
DTC 14-13: Go to step 11.
DTC 14-14: Go to step 19.
Intermittent failure, system is OK at this time.
Go to Troubleshooting Intermittent Failures
(see page 24-24).
4. Turn the ignition switch to LOCK (0). 5. Disconnect the ODS unit harness 3P connector (A)
from the front passenger’s weight sensor (front
inner side).
6. Read the DTC. Go to step 7.
Faulty front passenger’s weight sensor (front
inner side); replace the front passenger’s seat slide
assembly including all four front passenger’s
weight sensors (see page 24-207), then clear the
DTC.
7. Turn the ignition switch to LOCK (0).
8. Disconnect the ODS unit harness 18P connector (A) from the ODS unit.
(cont’d)
Is DTC 82-14 indicated?I s anot her DT C al so i nd i cat ed ? Is DTC 14-12 indicated?
08/08/21 14:00:48 61SNR030_240_0151
ProCarManuals.com
DYNOMITE -2009-
Î
(#'
'
)
µ
µµ
µ
YES
NO YES
NO
DTC 82-15:
DTC 82-17:
DTC 83-25:
DTC 83-27:
24-15524-155
ODS UNIT HARNESS 18P CONNECTOR
BRN BLK
25. Measure the resistance between ODS unit harness18P connector terminals No. 8 and No. 13. There
should be an open circuit or at least 1 M .
Faulty ODS unit; replace the ODS unit
(see page 24-209), then clear the DTC.
Short in the ODS unit harness; replace the
ODS unit harness, then clear the DTC. NOTE: Before doing this troubleshooting procedure,
review SRS Precautions and Procedures (see page
24-13) and General Troubleshooting Information
(see page 24-22).
1. Clear the DTC memory (see page 24-23).
2. Read the DTC (see page 24-22).
Faulty front passenger’s weight sensor;
replace the front passenger’s seat frame including
all four front passenger’s weight sensors (see page
24-207), then clear the DTC.
Intermittent failure, the system is OK at this
time. Go to Troubleshooting Intermittent Failures
(see page 24-24).Internal Failure of the Front
Passenger’s Weight Sensor (front inner side)
Internal Failure of the Front
Passenger’s Weight Sensor (rear inner side)
Internal Failure of the Front
Passenger’s Weight Sensor (front outer side)
Internal Failure of the Front
Passenger’s Weight Sensor (rear outer side
Wire side of female terminals
Is the resistance as specif ied?
Is DT C 82-15, 82-17 , 83-25, or 83-27 indicated?
08/08/21 14:00:50 61SNR030_240_0155
ProCarManuals.com
DYNOMITE -2009-
(#'
'
)
µ
µ
µ
µ µ
µ
DTC 82-16:
YES
NO
YES
NO YES
NO
24-156SRS
DTC Troubleshooting (cont’d)
A
A
No Signal from the Front
Passenger’s Weight Sensor (rear inner side)
NOTE: Before doing this troubleshooting procedure,
review SRS Precautions and Procedures (see page
24-13) and General Troubleshooting Information
(see page 24-22).
1. Clear the DTC memory (see page 24-23).
2. Read the DTC (see page 24-22).
Go to step 3.
Intermittent failure, system is OK at this time.
Go to Troubleshooting Intermittent Failures
(see page 24-24).
3. From INSPECTION the SRS menu on the HDS, select SWS DTC CHECK.
DTC 16-11: Short to power in the ODS unit harness; replace the ODS unit harness, then clear
the DTC.
DTC 16-12: Go to step 4.
DTC 16-13: Go to step 11.
DTC 16-14: Go to step 19.
Intermittent failure, system is OK at this time.
Go to Troubleshooting Intermittent Failures
(see page 24-24).
4. Turn the ignition switch to LOCK (0). 5. Disconnect the ODS unit harness 3P connector (A)
from the front passenger’s weight sensor (rear
inner side).
6. Read the DTC. Go to step 7.
Faulty front passenger’s weight sensor (rear
inner side); replace the front passenger’s seat slide
assembly including all four front passenger’s
weight sensors (see page 24-207), then clear the
DTC.
7. Turn the ignition switch to LOCK (0).
8. Disconnect the ODS unit harness 18P connector (A) from the ODS unit.
Is DTC 82-16 indicated?
I s anot her DT C al so i nd i cat ed ? Is DTC 16-12 indicated?
08/08/21 14:00:50 61SNR030_240_0156
ProCarManuals.com
DYNOMITE -2009-
(#'
')
µ
µ
µ
µ µ
µ
DTC 83-26:
YES
NO
YES
NO YES
NO
24-163
A
A
No Signal from the Front
Passenger’s Weight Sensor (rear outer side)
NOTE: Before doing this troubleshooting procedure,
review SRS Precautions and Procedures (see page
24-13) and General Troubleshooting Information
(see page 24-22).
1. Clear the DTC memory (see page 24-23).
2. Read the DTC (see page 24-22).
Go to step 3.
Intermittent failure, system is OK at this time.
Go to Troubleshooting Intermittent Failures
(see page 24-24).
3. From INSPECTION menu on the HDS, select SWS DTC CHECK.
DTC 26-11: Short to power in the ODS unit harness; replace the ODS unit harness, then clear
the DTC.
DTC 26-12: Go to step 4.
DTC 26-13: Go to step 11.
DTC 26-14: Go to step 19.
Intermittent failure, system is OK at this time.
Go to Troubleshooting Intermittent Failures
(see page 24-24).
4. Turn the ignition switch to LOCK (0). 5. Disconnect the ODS unit harness 3P connector (A)
from the front passenger’s weight sensor (rear
outer side).
6. Read the DTC. Go to step 7.
Faulty front passenger’s weight sensor (rear
outer side); replace the front passenger’s seat slide
assembly including all four front passenger’s
weight sensors (see page 24-207), then clear the
DTC.
7. Turn the ignition switch to LOCK (0).
8. Disconnect the ODS unit harness 18P connector (A) from the ODS unit.
(cont’d)
Is DTC 83-26 indicated?I s anot her DT C al so i nd i cat ed ? Is DTC 26-12 indicated?
08/08/21 14:00:53 61SNR030_240_0163
ProCarManuals.com
DYNOMITE -2009-
(#'
'
)(#'
')
µ
µ
µ
µ
µ
µ µ
µ
µ
µ
DTC 85-71, 85-78: DTC 85-79:
YES
NO
YES
NO
YES
NO YES
NO
YES
NO
24-16724-167
ODS Unit Not Initialize
OPDS Sensor Initial Check Failure
NOTE: Before doing this troubleshooting procedure,
review SRS Precautions and Procedures (see page
24-13) and General Troubleshooting Information
(see page 24-22).
1. Clear the DTC memory (see page 24-23).
2. Turn the ignition switch to ON (II), and check that the SRS indicator comes on for about 6 seconds
and then goes off.
Go to step 3.
Intermittent failure, system is OK at this time.
Go to Troubleshooting Intermittent Failures
(see page 24-24). If another DTC is indicated,
troubleshoot the DTC.
3. Initialize the ODS unit (see page 24-26).
4. Turn the ignition switch to ON (II), and check that the SRS indicator comes on for about 6 seconds
and then goes off.
The system is OK.
Go to step 5.
5. Replace the ODS unit (see page 24-209), then clear the DTC.
6. Turn the ignition switch to ON (II), and check that the SRS indicator comes on for about 6 seconds
and then goes off.
The system is OK.
Replace the SRS unit (see page 24-203). NOTE: Before doing this troubleshooting procedure,
review SRS Precautions and Procedures (see page
24-13) and General Troubleshooting Information
(see page 24-22).
1. Clear the DTC memory (see page 24-23).
2. Turn the ignition switch to ON (II), and check that the SRS indicator comes on for about 6 seconds
and then goes off.
Go to step 3.
Intermittent failure, the system is OK at this
time. Go to Troubleshooting Intermittent Failures
(see page 24-24).
3. Turn the ignition switch to LOCK (0).
4. Make sure nothing is on the front passenger’s seat.
5. Clear the DTC memory (see page 24-23).
6. Turn the ignition switch to ON (II), and check that the SRS indicator comes on for about 6 seconds
and then goes off.
Go to step 7.
Intermittent failure, the system is OK at this
time. Go to Troubleshooting Intermittent Failures
(see page 24-24).
(cont’d)
Does the SRS indicator stay on, and is DT C 85-71or 85 -7 8 i nd i cat ed ?
Does the SRS indicator go of f ?Does the SRS indicator go of f ? Does the SRS indicator go of f ?
Does the SRS indicator go of f ?
08/08/21 14:00:55 61SNR030_240_0167
ProCarManuals.com
DYNOMITE -2009-
(#'
'
-)
µ
µ
µ
µ
YES
NO
YES
NO
DTC 86-1x (‘‘x’’ can be 0 thru 9 or A thru F):
DTC 86-2x (‘‘x’’ can be 0 thru 9 or A thru F):
24-16824-168SRS
DTC Troubleshooting (cont’d)
7. Initialize the ODS unit (see page 24-26).
8. Turn the ignition switch to ON (II), and check that
the SRS indicator comes on for about 6 seconds
and then goes off.
Replace the ODS unit (see page 24-209), then
clear the DTC. If the problem is still present, replace
the OPDS sensor/seat-back (see page 20-123).
Intermittent failure, the system is OK at this
time. Go to Troubleshooting Intermittent Failures
(see page 24-24). NOTE: Before doing this troubleshooting procedure,
review SRS Precautions and Procedures (see page
24-13) and General Troubleshooting Information
(see page 24-22).
1. Clear the DTC memory (see page 24-23).
2. Turn the ignition switch to ON (II), and check that the SRS indicator comes on for about 6 seconds
and then goes off.
Go to step 3.
Intermittent failure, system is OK at this time.
Go to Troubleshooting Intermittent Failures
(see page 24-24). If another DTC is indicated,
troubleshoot the DTC.
NOTE: Aftermarket devices (fluorescent lights,
laptop computers, etc.) used near the front
passenger’s seat-back can interfere with the seat-
back sensors and cause a false DTC 86-1x or 86-2x.
If one of these devices was used, clear the DTC,
operate the device near the seat-back, and recheck
for DTCs. If DTC 86-1x or 86-2x is set, clear it, and
do not use the device near the seat-back.
Faulty OPDS Seat-Back Sensor
Faulty OPDS Seat Support Sensor
Does the SRS indicator go of f ?
Does the SRS indicator stay on, and is DT C 86-1xor 86-2x indicated?
08/08/21 14:00:55 61SNR030_240_0168
ProCarManuals.com
DYNOMITE -2009-
(#'
'
-)
µ
µ
µ
µ µ
µ
YES
NO
YES
NO YES
NO
DTC 92-1x (‘‘x’’ can be 0 thru 9 or A thru F):
24-16924-169
A
B
3. Check the connection at the OPDS sensor harness
connectors (A) and the ODS unit harness 18P
connector (B).
Go to step 4.
Repair the poor connection, then clear the
DTC.
4. Replace the OPDS sensor/seat-back foam (see page 20-123), and initialize the ODS unit (see page 24-26),
then clear the DTC.
5. Clear the DTC memory, then check for DTC 86-1x or 86-2x.
Replace the ODS unit (see page 24-209), then
clear the DTC.
The system is OK. NOTE: Before doing this troubleshooting procedure,
review SRS Precautions and Procedures (see page
24-13), General Troubleshooting Information (see page
24-22), and Battery Terminal Disconnection and
Reconnection (see page 22-68).
1. Clear the DTC memory (see page 24-23).
2. Turn the ignition switch to ON (II), and check that the SRS indicator comes on for about 6 seconds
and then goes off.
Go to step 3.
Intermittent failure, system is OK at this time.
Go to Troubleshooting Intermittent Failures
(see page 24-24). If another DTC is indicated,
troubleshoot the DTC.
3. Turn the ignition switch to LOCK (0). Disconnect the negative cable from the battery, then wait at least
3 minutes.
4. Disconnect the passenger’s airbag cutoff indicator 4P connector (see page 24-212).
(cont’d)
Open in the Passenger’s Airbag Cutoff
Indicator
I s t he connect i on OK ?Is DT C 86-1x or 86-2x indicated? Does the SRS indicator stay on, and is DT C 92-1x
indicated?
08/08/21 14:00:55 61SNR030_240_0169
ProCarManuals.com
DYNOMITE -2009-
(#'
'
-)
µ
µ
µ
µ µ
µ
µ
µ
YES
NO
YES
NO YES
NO
YES
NO
DTC A1-1x (‘‘x’’ can be 0 thru 9 or A thru F):
24-17124-171
SRS UNIT CONNECTOR A (28P)
PASSENGER’S AIRBAG CUTOFF
INDICATOR 4P CONNECTOR BLU
SRS UNIT CONNECTOR A (28P)
6. Measure the resistance between SRS unitconnector A (28P) terminal No. 13 and passenger’s
airbag cutoff indicator 4P connector terminal No. 4.
There should be less than 1.0 .
Go to step 7.
Open in the dashboard wire harness; replace
the dashboard wire harness, then clear the DTC.
7. Measure the resistance between SRS unit connector A (28P) terminal No. 13 body ground.
There should be an open circuit or at least 1 M .
Check for a faulty SRS unit or passenger’s
airbag cutoff indicator; replace the passenger’s
airbag cutoff indicator (see page 24-212), then clear
the DTC. If the problem is still present, replace the
SRS unit (see page 24-203).
Short to ground in the dashboard wire
harness; replace the dashboard wire harness, then
clear the DTC. NOTE: Before doing this troubleshooting procedure,
review SRS Precautions and Procedures (see page
24-13), General Troubleshooting Information (see page
24-22), and Battery Terminal Disconnection and
Reconnection (see page 22-68).
1. Clear the DTC memory (see page 24-23).
2. Turn the ignition switch to ON (II), and wait for 10 seconds.
3. Read the DTC (see page 24-22).
Go to step 4.
Intermittent failure, system is OK at this time.
Go to Troubleshooting Intermittent Failures
(see page 24-24). If another DTC is indicated,
troubleshoot the DTC.
4. Turn the ignition switch to LOCK (0).
5. Check the No. 9 (7.5 A) fuse in the under-dash fuse/ relay box.
Go to step 6.
Replace the fuse, then turn the ignition switch
to ON (II). If the fuse blows again, check for a short
in the No. 9 (7.5 A) fuse circuit (dashboard wire
harness, floor wire harness, front passenger’s seat
wire harness (with seat heater), or ODS unit
harness), then clear the DTC.
6. Disconnect the negative cable from the battery, then wait at least 3 minutes.
7. Disconnect the SRS unit connector A (28P) from the SRS unit (see step 9 on page 24-21).
8. Reconnect the negative cable to the battery.
9. Turn the ignition switch to ON (II).
(cont’d)
Faulty Power supply (VA Line)
Wire side of female terminals
Wire side of female terminals
Wire side of female terminals
Is the resistance as specif ied?
Is the resistance as specif ied? I s DT C A1-1x i nd i cat ed ?
IsthefuseOK?
08/08/21 14:00:56 61SNR030_240_0171
ProCarManuals.com
DYNOMITE -2009-