2006 ACURA CSX seat memory


(#' 
'-)
µ
µ
DTC 22-3x (‘‘x’’ can be 0 thru 9 or A thru F):
Special Tools Required
YES
NO
24-70SRS
DTC Troubleshooting (cont’d)
A
070AZ-SNAA200 07SAZ-TB4011A
Short to Another Wire or Decreased
Resistance in the Front Passenger’s Seat Belt
Tensioner
 SRS inflator simulator 07SAZ-TB4011A
 SRS simulator lead K 070AZ-SNAA200
NOTE: Before doing this troubleshooting procedure,
review SRS Precautions and Procedures (see page
24-13), General Troubleshooting Information (see page
24-22), and Battery Terminal Disconnection and
Reconnection (see page 22-68).
1. Clear the DTC memory (see page 24-23).
2. Turn the ignition switch to ON (II), and check that the SRS indicator comes on for about 6 seconds
and then goes off.
Go to step 3.
Intermittent failure, system is OK at this time.
Go to Troubleshooting Intermittent Failures
(see page 24-24). If another DTC is indicated,
troubleshoot the DTC.
3. Turn the ignition switch to LOCK (0). Disconnect the negative cable from the battery, then wait at least 3
minutes. 4. Remove the B-pillar lower trim (see page 20-72),
then disconnect the floor wire harness 4P
connector (A) from the front passenger’s seat belt
tensioner.
5. Connect the SRS inflator simulator (2 connectors) and simulator lead K to the floor wire
harness.
Does the SRS indicator stay on, and is DT C 22-3xindicated?
08/08/21 13:56:56 61SNR030_240_0070
ProCarManuals.com
DYNOMITE -2009-


µ
µ
µ
µ
YES
NO
YES
NO
24-71
SRS UNIT CONNECTOR B (28P)
6. Reconnect the negative cable to the battery.
7. Clear the DTC memory.
8. Read the DTC (see page 24-22).Go to step 9.
Short in the front passenger’s seat belt
tensioner; replace the front passenger’s seat belt
(see page 24-4), then clear the DTC.
9. Turn the ignition switch to LOCK (0). Disconnect the negative cable from the battery, then wait at least 3
minutes.
10. Disconnect both seat belt buckle tensioner connectors (see step 8 on page 24-21) and driver’s
seat belt tensioner connector (see step 7 on page
24-21).
11. Disconnect SRS unit connector B (28P) from the SRS unit (see step 9 on page 24-21).
12. Disconnect the simulator lead from the floor wire harness. 13. Measure the resistance between SRS unit
connector B (28P) terminals No. 3 and No. 4. There
should be an open circuit or at least 1 M .
Faulty SRS unit or poor connection at SRS
unit connector B (28P) and the SRS unit. Check the
connection; if the connection is OK, replace the
SRS unit (see page 24-203).
Short in the floor wire harness; replace the
floor wire harness, then clear the DTC.
Wire side of female terminals
Is DTC 22-3x indicated?
Is the resistance as specif ied?
08/08/21 13:56:56 61SNR030_240_0071
ProCarManuals.com
DYNOMITE -2009-


(#' 
'-)
µ
µ
DTC 22-8x (‘‘x’’ can be 0 thru 9 or A thru F):
Special Tools Required
YES
NO
24-72SRS
DTC Troubleshooting (cont’d)
A
070AZ-SNAA200 07SAZ-TB4011A
Short to Power in the Front Passenger’s Seat
Belt Tensioner
 SRS inflator simulator 07SAZ-TB4011A
 SRS simulator lead K 070AZ-SNAA200
NOTE: Before doing this troubleshooting procedure,
review SRS Precautions and Procedures (see page
24-13), General Troubleshooting Information (see page
24-22), and Battery Terminal Disconnection and
Reconnection (see page 22-68).
1. Clear the DTC memory (see page 24-23).
2. Turn the ignition switch ON (II), and check that the SRS indicator comes on for about 6 seconds and
then goes off.
Go to step 3.
Intermittent failure, system is OK at this time.
Go to Troubleshooting Intermittent Failures
(see page 24-24). If another DTC is indicated,
troubleshoot the DTC.
3. Turn the ignition switch to LOCK (0). Disconnect the negative cable from the battery, then wait at least 3
minutes. 4. Remove the B-pillar lower trim (see page 20-72),
then disconnect the floor wire harness 4P
connector (A) from the front passenger’s seat belt
tensioner.
5. Connect the SRS inflator simulator (2 connectors) and simulator lead K to the floor wire
harness.
6. Reconnect the negative cable to the battery.
7. Clear the DTC memory.
Does the SRS indicator stay on, and is DT C 22-8x indicated?
08/08/21 13:56:57 61SNR030_240_0072
ProCarManuals.com
DYNOMITE -2009-


(#' 
'-)
µ
µ
DTC 22-9x (‘‘x’’ can be 0 thru 9 or A thru F):
Special Tools Required
YES
NO
24-74SRS
DTC Troubleshooting (cont’d)
A
070AZ-SNAA200 07SAZ-TB4011A
Short to Ground in the Front Passenger’s
Seat Belt Tensioner
 SRS inflator simulator 07SAZ-TB4011A
 SRS simulator lead K 070AZ-SNAA200
NOTE: Before doing this troubleshooting procedure,
review SRS Precautions and Procedures (see page
24-13), General Troubleshooting Information (see page
24-22), and Battery Terminal Disconnection and
Reconnection (see page 22-68).
1. Clear the DTC memory (see page 24-23).
2. Turn the ignition switch to ON (II), and check that the SRS indicator comes on for about 6 seconds
and then goes off.
Go to step 3.
Intermittent failure, system is OK at this time.
Go to Troubleshooting Intermittent Failures
(see page 24-24). If another DTC is indicated,
troubleshoot the DTC.
3. Turn the ignition switch to LOCK (0). Disconnect the negative cable from the battery, then wait at least 3
minutes. 4. Remove the B-pillar lower trim (see page 20-72),
then disconnect the floor wire harness 4P
connector (A) from the front passenger’s seat belt
tensioner.
5. Connect the SRS inflator simulator (2 connectors) and simulator lead K to the floor wire
harness.
6. Reconnect the negative cable to the battery.
7. Clear the DTC memory.
Does the SRS indicator stay on, and is DT C 22-9x indicated?
08/08/21 13:56:57 61SNR030_240_0074
ProCarManuals.com
DYNOMITE -2009-


(#' 
'
-)
µ
µ
DTC 27-1x (‘‘x’’ can be 0 thru 9 or A thru F):
Special Tools Required
YES
NO
24-76SRS
DTC Troubleshooting (cont’d)
B
A
070AZ-SNAA200 07SAZ-TB4011A
Open in the Driver’s Seat Belt Buckle
Tensioner
 SRS inflator simulator 07SAZ-TB4011A
 SRS simulator lead K 070AZ-SNAA200
NOTE: Before doing this troubleshooting procedure,
review SRS Precautions and Procedures (see page
24-13), General Troubleshooting Information (see page
24-22), and Battery Terminal Disconnection and
Reconnection (see page 22-68).
1. Clear the DTC memory (see page 24-23).
2. Turn the ignition switch to ON (II), and check that the SRS indicator comes on for about 6 seconds
and then goes off.
Go to step 3.
Intermittent failure, system is OK at this time.
Go to Troubleshooting Intermittent Failures
(see page 24-24). If another DTC is indicated,
troubleshoot the DTC.
3. Turn the ignition switch to LOCK (0). Disconnect the negative cable from the battery, then wait at least 3
minutes. 4. Disconnect the floor wire harness 4P connector (A)
from the driver’s seat belt buckle tensioner
connector (B).
5. Connect the SRS inflator simulator (2 connectors) and simulator lead K to the floor wire
harness connector.
6. Reconnect the negative cable to the battery.
7. Clear the DTC memory.
Does the SRS indicator stay on, and is DT C 27-1x indicated?
08/08/21 13:56:58 61SNR030_240_0076
ProCarManuals.com
DYNOMITE -2009-


(#' 
'-)
µ
µ
DTC 27-3x (‘‘x’’ can be 0 thru 9 or A thru F):
Special Tools Required
YES
NO
24-78SRS
DTC Troubleshooting (cont’d)
B
A
070AZ-SNAA200 07SAZ-TB4011A
Short to Another Wire or Decreased
Resistance in the Driver’s Seat Belt Buckle
Tensioner
 SRS inflator simulator 07SAZ-TB4011A
 SRS simulator lead K 070AZ-SNAA200
NOTE: Before doing this troubleshooting procedure,
review SRS Precautions and Procedures (see page
24-13), General Troubleshooting Information (see page
24-22), and Battery Terminal Disconnection and
Reconnection (see page 22-68).
1. Clear the DTC memory (see page 24-23).
2. Turn the ignition switch to ON (II), and check that the SRS indicator comes on for about 6 seconds
and then goes off.
Go to step 3.
Intermittent failure, system is OK at this time.
Go to Troubleshooting Intermittent Failures
(see page 24-24). If another DTC is indicated,
troubleshoot the DTC.
3. Turn the ignition switch to LOCK (0). Disconnect the negative cable from the battery, then wait at least 3
minutes. 4. Disconnect the floor wire harness 4P connector (A)
from the driver’s seat belt buckle tensioner
connector (B).
5. Connect the SRS inflator simulator (2 connectors) and simulator lead K to the floor wire
harness connector.
6. Reconnect the negative cable to the battery.
7. Clear the DTC memory.
Does the SRS indicator stay on, and is DT C 27-3x indicated?
08/08/21 13:56:58 61SNR030_240_0078
ProCarManuals.com
DYNOMITE -2009-


(#' 
'-)
µ
µ
DTC 27-8x (‘‘x’’ can be 0 thru 9 or A thru F):
Special Tools Required
YES
NO
24-80SRS
DTC Troubleshooting (cont’d)
B
A
070AZ-SNAA200 07SAZ-TB4011A
Short to Power in the Driver’s Seat Belt
Buckle Tensioner
 SRS inflator simulator 07SAZ-TB4011A
 SRS simulator lead K 070AZ-SNAA200
NOTE: Before doing this troubleshooting procedure,
review SRS Precautions and Procedures (see page
24-13), General Troubleshooting Information (see page
24-22), and Battery Terminal Disconnection and
Reconnection (see page 22-68).
1. Clear the DTC memory (see page 24-23).
2. Turn the ignition switch to ON (II), and check that the SRS indicator comes on for about 6 seconds
and then goes off.
Go to step 3.
Intermittent failure, system is OK at this time.
Go to Troubleshooting Intermittent Failures
(see page 24-24). If another DTC is indicated,
troubleshoot the DTC.
3. Turn the ignition switch to LOCK (0). Disconnect the negative cable from the battery, then wait at least 3
minutes. 4. Disconnect the floor wire harness 4P connector (A)
from the driver’s seat belt buckle tensioner
connector (B).
5. Connect the SRS inflator simulator (2 connectors) and simulator lead K to the floor wire
harness connector.
6. Reconnect the negative cable to the battery.
7. Clear the DTC memory.
Does the SRS indicator stay on, and is DT C 27-8x indicated?
08/08/21 13:56:58 61SNR030_240_0080
ProCarManuals.com
DYNOMITE -2009-


(#' 
'-)
µ
µ
DTC 27-9x (‘‘x’’ can be 0 thru 9 or A thru F):
Special Tools Required
YES
NO
24-82SRS
DTC Troubleshooting (cont’d)
B
A
070AZ-SNAA200 07SAZ-TB4011A
Short to Ground in the Driver’s Seat Belt
Buckle Tensioner
 SRS inflator simulator 07SAZ-TB4011A
 SRS simulator lead K 070AZ-SNAA200
NOTE: Before doing this troubleshooting procedure,
review SRS Precautions and Procedures (see page
24-13), General Troubleshooting Information (see page
24-22), and Battery Terminal Disconnection and
Reconnection (see page 22-68).
1. Clear the DTC memory (see page 24-23).
2. Turn the ignition switch to ON (II), and check that the SRS indicator comes on for about 6 seconds
and then goes off.
Go to step 3.
Intermittent failure, system is OK at this time.
Go to Troubleshooting Intermittent Failures
(see page 24-24). If another DTC is indicated,
troubleshoot the DTC.
3. Turn the ignition switch to LOCK (0). Disconnect the negative cable from the battery, then wait at least 3
minutes. 4. Disconnect the floor wire harness 4P connector (A)
from the driver’s seat belt buckle tensioner
connector (B).
5. Connect the SRS inflator simulator (2 connectors) and simulator lead K to the floor wire
harness connector.
6. Reconnect the negative cable to the battery.
7. Clear the DTC memory.
Does the SRS indicator stay on, and is DT C 27-9x indicated?
08/08/21 13:56:59 61SNR030_240_0082
ProCarManuals.com
DYNOMITE -2009-