2006 ACURA CSX clutch

Ø
ECM/PCM Inputs and Outputs at Connector A ( ) (44P)
Terminal
numberWire color Terminal name DescriptionSignal
11-27
NOTE: Standard battery voltage is about 12 V.
39 BRN BKSWNC (BRAKE PEDAL POSITION SWITCH) Detects brake pedal
position switch signalWith ignition switch ON (II) and brake pedal
released: battery voltage
With ignition switch ON (II) and brake pedal
pressed: about 0 V
40 LT GRN BKSW (BRAKE PEDAL POSITION SWITCH) Detects brake pedal
position switch signalWith brake pedal released: about 0 V
With brake pedal pressed: battery voltage
41 LT BLU CRMTCLS (CRUISE CLUTCH PEDAL POSITION
SIGNAL) Detects clutch pedal
position switch signal
With ignition switch ON (II) and clutch pedal
released: about 0 V
With ignition switch ON (II) and clutch pedal
pressed: battery voltage
42 RED WEN (WRITE ENABLE SIGNAL) Detects write enable signal With ignition switch ON (II): about 0 V
44 PNK S-NET5V (SERIAL COMMUNICATION FOR
IMMOBILIZER) Sends serial
communication signal
With ignition switch ON (II): pulses
With ignition switch OFF: about 5.0 V
2: M/T
(cont’d)
2
Terminal side of female terminals
08/08/21 14:12:43 61SNR030_110_0027
ProCarManuals.com
DYNOMITE -2009-

ÎÚ
ECM/PCM Inputs and Outputs at Connector B ( ) (44P)
Terminal
numberWire color Terminal name DescriptionSignal
11-28Fuel and Emissions Systems
System Description (cont’d)
NOTE: Standard battery voltage is about 12 V.




1BLK/RED
(BLK) PG2 (POWER GROUND) Ground circuit for ECM/
PCMLess than 1.0 V at all times
2 BLU/RED EGR (EXHAUST GAS RECIRCULATION (EGR)
VALVE) Drives EGR valve With EGR operating: duty controlled
With EGR not operating: about 0 V
3 YEL/BLU PCS (EVAPORATIVE EMISSION (EVAP)
CANISTER PURGE VALVE) Drives EVAP canister purge
valve
With engine running, engine coolant below 60 °C
(140 °F): battery voltage
With engine running, engine coolant above 60 °C
(140 °F): duty controlled
4 BLK/WHT SO2SHTC (SECONDARY HEATED OXYGEN SENSOR
(SECONDARY HO2S)
HEATER (SENSOR 2)) Drives secondary HO2S
heater (sensor 2)
With ignition switch ON (II): battery voltage
With warmed up engine running: duty controlled
7 YEL/RED OPSW (OIL PRESSURE SWITCH) Detects engine oil pressure
signalWith ignition switch OFF: about 0 V
With engine running: battery voltage
8 BLU/RED OP2SW (2ND CLUTCH TRANSMISSION FLUID
PRESSURE SWITCH) Detects 2nd clutch
transmission fluid pressure
switch inputWith ignition switch ON (II):
Without 2nd clutch pressure: about 5.0 V
With 2nd clutch pressure: about 0 V
9 BLU/WHT OP3SW (3RD CLUTCH TRANSMISSION FLUID
PRESSURE SWITCH) Detects 3rd clutch
transmission fluid pressure
switch inputWith ignition switch ON (II):
Without 3rd clutch pressure: about 5.0 V
With 3rd clutch pressure: about 0 V
10 BLU/BLK SHA (SHIFT SOLENOID VALVE A) Drives shift solenoid
valve AWith engine running in R, D, and S (in 1st, 4th, or
5th gears): battery voltage
With engine running in P, N, D, and S (in 2nd and
3rd gears): about 0 V
11 GRN/WHT SHB (SHIFT SOLENOID VALVE B) Drives shift solenoid
valve BWith engine running in P, R, N, D, and S (in 1st and
2nd gears): battery voltage
With engine running in D and S (in 3rd, 4th, 5th
gears): about 0 V
12 RED/BLK ATPN (TRANSMISSION RANGE SWITCH N) Detects transmission range
switch N position signal
inputIn N: about 0 V
In any position other than N: about 5.0 V
13 BLU/BLK ATPP (TRANSMISSION RANGE SWITCH P) Detects transmission range
switch P position signal
inputIn P: about 0 V
In any position other than P: about 5.0 V
14 WHT ATPR (TRANSMISSION RANGE SWITCH R) Detects transmission range
switch R position signal
inputIn R: about 0 V
In any position other than R: about 5.0 V
15 RED ATPS (TRANSMISSION RANGE SWITCH S) Detects transmission range
switch S position signal
inputIn S: about 0 V
In any position other than S: battery voltage
1: A/T
4: K20Z2 engine
5: ’07-09 models
5
4
1
1
1
1
1
1
1
1
Terminal side of female terminals
08/08/21 14:12:43 61SNR030_110_0028
ProCarManuals.com
DYNOMITE -2009-

´´´
´
µ
µ
µ
ÎÚ
ECM/PCM Inputs and Outputs at Connector B ( ) (44P)
Terminal
numberWire color Terminal name DescriptionSignal
11-29
NOTE: Standard battery voltage is about 12 V.


16 BLU/YEL SUPP (PADDLE SHIFTER
(UPSHIFT SWITCH)) Detects paddle shifter
(upshift switch)In S:
With paddle shifter (upshift switch) pressed:
about 0 V
With paddle shifter (upshift switch) released:
battery voltage
17 WHT/RED NM (INPUT SHAFT (MAINSHAFT) SPEED
SENSOR) Detects input shaft
(mainshaft) speed sensor
signalWith ignition switch ON (II): about 0 V
With engine idling in N: about 2.5 V
18 YEL/BLU (YEL)VCC2 (SENSOR VOLTAGE) Provides sensor reference
voltageWith ignition switch ON (II): about 5.0 V
20 GRN SHC (SHIFT SOLENOID VALVE C) Drives shift solenoid
valve CWith engine running in N and S (in 1st, 3rd, and 5th
gears): battery voltage
With engine running in P, R, D, and S (in 2nd and
4th gears): about 0 V
21 YEL/GRN ATPD (TRANSMISSION RANGE SWITCH D) Detects transmission range
switch D position signal
inputIn D: about 0 V
In any position other than D: battery voltage
22 RED/WHT ATPRVS (TRANSMISSION RANGE SWITCH RVS) Detects transmission range
switch RVS position signal
inputIn R: about 0 V
In any position other than R: battery voltage
23 RED/WHT ECT1 (ENGINE COOLANT TEMPERATURE (ECT)
SENSOR 1) Detects ECT sensor 1 signal With ignition switch ON (II): about 0.1 4.8 V
(depending on engine coolant temperature)
24 YEL SHE (SHIFT SOLENOID VALVE E) Drives shift solenoid
valve EWith engine running in P and R: battery voltage
With engine running in N, D, and S (in 1st gear):
about 0 V
25 BLU/YEL LSC (A/T CLUTCH PRESSURE CONTROL
SOLENOID VALVE C) Drives A/T clutch pressure
control solenoid valve C
With ignition switch ON (II): current controlled
26 GRN/RED SHD (SHIFT SOLENOID VALVE D) Drives shift solenoid
valve DWith engine running in D and S (in 2nd and 5th
gears): battery voltage
With engine running in P, R, N, D, and S (in 1st, 3rd,
and 4th gears): about 0 V
27 RED/YEL TATF (ATF TEMPERATURE SENSOR) Detects ATF temperature
signalWith ignition switch ON (II): about 0.2 4.0 V
(about 1.8 V at operating temperature)
(depending on ATF temperature)
28 BLU/YEL ATPFWD (TRANSMISSION RANGE SWITCH FWD) Detects transmission range
switch D and S positions
signalIn D and S: about 0 V
In any other position D and S: battery voltage
29 WHT/BLK EGRP (EXHAUST GAS RECIRCULATION (EGR)
VALVE POSITION SENSOR) Detects EGR valve position
sensor signal
With engine running: about 1.2 3.0 V
(depending on EGR valve lift)
1: A/T
3: K20Z3 engine
4: K20Z2 engine
(cont’d)
1
1
3
1
1
1
1
1
1
1
1
4
Terminal side of female terminals
08/08/21 14:12:44 61SNR030_110_0029
ProCarManuals.com
DYNOMITE -2009-

´´ µ
´µ µ
µ µ
µµ µ
µ
µ
ÎÚ
ECM/PCM Inputs and Outputs at Connector B ( ) (44P)
Terminal
numberWire color Terminal name DescriptionSignal
11-30Fuel and Emissions Systems
System Description (cont’d)
NOTE: Standard battery voltage is about 12 V.


30 RED/BLK VG (MASS AIR FLOW
(MAF) SENSOR SIDE) Detects MAF sensor signal At idle: about 1.1 1.6 V
(between VG terminal and VG terminal)
31 RED/YEL IAT (INTAKE AIR TEMPERATURE (IAT)
SENSOR) Detects IAT sensor signal With ignition switch ON (II): about 0.1 4.0 V
(about 1.8 V at normal operating temperature)
32 BLK/BLU VG (MASS AIR FLOW (MAF) SENSOR SIDE) Ground for MAF sensor
signal
33 GRN/BLK SG2 (SENSOR GROUND) Sensor ground Less than 1.0 V at all times
34 GRN/YEL VTS (ROCKER ARM OIL CONTROL SOLENOID) Drives rocker arm oil
control solenoidAt idle: about 0 V
35 BRN LSB (A/T CLUTCH PRESSURE CONTROL
SOLENOID VALVE B) Drives A/T clutch pressure
control solenoid valve B
With ignition switch ON (II): current controlled
36 BLK PG1 (POWER GROUND) Ground circuit for ECM/ PCMLess than 1.0 V at all times
40 BRN SDNP (PADDLE SHIFTER (DOWN SHIFT SWITCH)) Detects paddle shifter
(downshift switch) signalIn S:
With paddle shifter (downshift switch) pressed:
about 0 V
With paddle shifter (downshift switch) released:
about 5.0 V
41 WHT/GRN ALTC (ALTERNATOR CONTROL) Sends alternator control
signalWith warmed up engine running: about 5.0 V
(depending on electrical load)
42 WHT/BLU ALTL (ALTERNATOR L SIGNAL) Detects alternator L signal With ignition switch ON (II): about 0 V
With engine running: battery voltage
43 WHT/RED ALTF (ALTERNATOR FR SIGNAL) Detects alternator FR signal With engine running: about 2.6 3.4 V
(depending on electrical load)
44 RED/BLK LSA (A/T CLUTCH PRESSURE CONTROL
SOLENOID VALVE A) Drives A/T clutch pressure
control solenoid valve A
With ignition switch ON (II): current controlled
1: A/T
1
1
1
Terminal side of female terminals
08/08/21 14:12:44 61SNR030_110_0030
ProCarManuals.com
DYNOMITE -2009-








PGM-FI System
Air Conditioning (A/C) Compressor Clutch Relay
Air Fuel Ratio (A/F) Sensor
Barometric Pressure (BARO) Sensor
Camshaft Position (CMP) Sensor BCrankshaft Position (CKP) Sensor
Engine Coolant Temperature (ECT) Sensor 1 and 2
Ignition Timing Control
Injector Timing and Duration
11-33
ZIRCONIA
ELEMENT
SENSOR
TERMINALS
HEATER
TERMINALS
O-RING
MAGNET
TERMINAL TERMINAL
O-RING
MAGNET
THERMISTOR O-RING TERMINAL
The programmed fuel injection (PGM-FI) system is a
sequential multiport fuel injection system.
When the ECM/PCM receives a demand for cooling
from the A/C system, it delays the compressor from
being energized, and enriches the mixture to assure
smooth transition to the A/C mode.
The A/F sensor operates over a wide air/fuel range. The
A/F sensor is installed upstream of the TWC, and sends
signals to the ECM/PCM which varies the duration of
fuel injection accordingly.
The BARO sensor is inside the ECM/PCM. It converts
atmospheric pressure into a voltage signal that
modifies the basic duration of the fuel injection
discharge.
CMP sensor B detects the position of the No. 1 cylinder
as a reference for sequential fuel injection to each
cylinder. The CKP sensor detects crankshaft speed and is used by
the ECM/PCM to determine the ignition timing, timing
for the fuel injection of each cylinder, and engine
misfire detection.
ECT sensors 1 and 2 are temperature dependent
resistors (thermistors). The resistance decreases as the
engine coolant temperature increases.
The ECM/PCM contains the memory for basic ignition
timing at various engine speeds and manifold absolute
pressures. It also adjusts the timing according to engine
coolant temperature and intake air temperature.
The ECM/PCM contains the memory for basic discharge
duration at various engine speeds and manifold
pressures. The basic discharge duration, after being
read out from the memory, is further modified by
signals sent from various sensors to obtain the final
discharge duration.
By monitoring long term fuel trim, the ECM/PCM
detects long term malfunctions in the fuel system and
sets diagnostic trouble codes (DTCs) if needed.
(cont’d)
08/08/21 14:13:37 61SNR030_110_0033
ProCarManuals.com
DYNOMITE -2009-

Î

´
µ
ECM/PCM Circuit Diagram (K20Z2 engine) (cont’d)
11-48Fuel and Emissions Systems
System Description (cont’d)
1
2
3
BLK/YEL
4
GRN/BLK
5
RED/YEL
B30
VG
RED/BLK
B32
VG BLK/BLU
G
B33
SG2 GRN/BLK
B31
IAT RED/YEL F
N *1
ECT SENSOR 1
B23
ECT1
RED/WHT GRN/BLK
RED/WHT
B36
PG1 BLK
B1
PG2 BLK/RED
(BLK)*4
C2
PGMETCS BLK
G101
3
A39
BKSWNC BRN Brake pedal pressed: closed
Brake pedal released: open
Brake pedal pressed: open
Brake pedal released: closed
4
YEL 1
WHT 2
LT GRN
SU T BRAKE PEDAL
POSITION SWITCH
LT BLU Clutch pedal pressed: open
Clutch pedal released: closed
CLUTCH PEDAL
POSITION SWITCH
A41
CRMTCLS
3 2
G401 BLK
*2 C40
LG1
BRN/YEL
C44
LG2 BRN/YEL
G101D
IJ
H
18
1920 BRN
BRN
BRN/YEL C101
AF
AG
BRN/
YEL BRN/
YEL
21
*4
*3*4 1 2
MAF
SENSOR
IAT
SENSOR
6 5
*1: A/T
*2: M/T
*3: ’06 model
*4: ’07-09 models
08/08/21 14:13:46 61SNR030_110_0048
ProCarManuals.com
DYNOMITE -2009-

Î
ECM/PCM Circuit Diagram (K20Z2 engine) (cont’d)
11-50Fuel and Emissions Systems
System Description (cont’d)
ATF TEMPERATURE
SENSOR
N
WHT
WHT
SHIFT SOLENOID
VALVE A
BLU
SHIFT SOLENOID
VALVE B
ORN
GRN/BLK
6
SHIFT SOLENOID
VALVE C
GRN
7
5
2
1
A/T CLUTCH PRESSURE
CONTROL SOLENOID VALVE A
A/T CLUTCH PRESSURE
CONTROL SOLENOID VALVE BA/T CLUTCH PRESSURE
CONTROL SOLENOID VALVE C
INPUT SHAFT
(MAINSHAFT)
SPEED SENSOR
GRN/BLK YEL/BLU
E 1
2
1
2
1
2
BLK/RED
(BLK)*4
G101 1
2
3 SHIFT SOLENOID
VALVE D
YEL
8
SHIFT SOLENOID
VALVE E
RED
3
*1
B27RED/YEL
B10 BLU/BLK
B11 GRN/WHT
TATF
SHA SHBB20 GRN
SHC
RED/BLK
B44
BRNBLU/YEL
B35
B25
WHT/RED
B17 LSA
LSB
LSC
NMB26
GRN/RED
SHD
B24 YEL
SHE
BLK/RED
(BLK)*4BLK/RED
(BLK)*4
*1: A/T
*4: ’07-09 models
08/08/21 14:13:47 61SNR030_110_0050
ProCarManuals.com
DYNOMITE -2009-

Î

11-51
2ND CLUTCH
TRANSMISSION FLUID
PRESSURE SWITCH
3RD CLUTCH
TRANSMISSION FLUID
PRESSURE SWITCH
1
1
BLU/RED
BLU/WHT
BLU/WHT
RED/BLK
BLU/BLK
WHT 7
YEL/GRN
RED/WHT RED
BLU/YEL 4
9
3
8
6
10
1 P
R
N
D
TRANSMISSION
RANGE SWITCH S
G101 BLU/WHT
RED/BLK
BLK/BLU
WHT 4
PNK
BLK
WHT/RED BLU
YEL/RED 6
7
2 8
3
5
1
10
5
OUTPUT SHAFT
(COUNTERSHAFT)
SPEED SENSOR
YEL/RED
B
GRN/WHT1
2
3
C
*1
B8
B9 OP2SW
OP3SW 17
16 23 22
B13
B14 BLU/BLK
WHT
B21 B12 ATPP
ATPR
ATPD
ATPN
B15 ATPS
B28 ATPFWD
B22 ATPRVS BLU/
BLK
C101
BLK/WHT
C43
NC
4C101
O
ORN
CLUTCH
INTERLOCK
SWITCHClutch pedal pressed: closed
Clutch pedal released: open
BLK ORN 1
2
G401 BLK/RED
(BLK)*4
*2
WHT
20
*1: A/T
*2: M/T
*4: ’07-09 models
(cont’d)
08/08/21 14:13:48 61SNR030_110_0051
ProCarManuals.com
DYNOMITE -2009-