2006 ACURA CSX immobilizer


(#')
µ
µ
µ
µ
YES
NO
YES
NO
22-93
Troubleshooting - B-CAN System Diagnosis Test Mode A
A
Check the ECM/PCM for DTCs and troubleshoot ECM/
PCM (see page 11-3) or F-CAN loss of communication
errors first, then do this diagnosis if the symptom is
relatedtotheB-CANsystem.
NOTE: If the HDS is not available, do the Test Mode 1 and Test Mode 2 (see page 22-97).
 Always cycle the ignition switch within 3 seconds when prompted in the DTC troubleshooting
procedures.
1. Compare the symptom with this list of B-CAN related systems:
 Gauge control module
 Exterior lights
 Turn signals
 Entry light control
 Interior lights
 Door-open and trunk-open indicators
 Horns (security and panic)
 Chimes (key-in, seat belt, lights-on, and parking brake)
 Power window/moonroof timer
 Wiper/washer
Security
 Keyless entry
 Power door locks
Keyinterlock
 Dash light brightness control
Go to step 2.
Go to the system troubleshooting for the
system with the symptom. 2. Connect the HDS to the data link connector (A),
then turn the ignition switch to ON (II).
3. From the BODY ELECTRICAL menu, select UNIT INFORMATION, and then select CONNECTED UNIT
listed to see if the following control units are
communicating with the HDS.
MICU
 Gauge control module
 Immobilizer-keyless control unit
 Climate control unit
 HandsFreeLink control unit
NOTE:  If one or more of the units are not communicating with the HDS, DETECT will be
displayed.
 If the unit is not communicating or the vehicle is not equipped, ‘‘Not Available’’ will be displayed.
Go to step 4.
If any of the control units are not
communicating, go to B-CAN System Diagnosis
Test Mode B (see page 22-94). If all units are not
communicating or only the MICU is communicating,
go to DTC B1000 troubleshooting (see page 22-102).
(cont’d)
Is the symptom related to the B-CAN system? Ar e al l cont r ol uni t s communi cat i ng w i t h t he H DS?
08/08/21 14:24:59 61SNR030_220_0095
ProCarManuals.com
DYNOMITE -2009-

(#')
µ
µ
µ
µ
YES
NO
YES
NOUnit not communicating
22-9422-94Multiplex Integrated Control System
Troubleshooting - B-CAN System
Diagnosis Test Mode A (cont’d)
Troubleshooting - B-CAN System
Diagnosis Test Mode B
4. Select the system that has the problem from the
BODY ELECTRICAL menu, then select DTCs.
Go to step 5.
If the problem is related to one of the
following items, go to B-CAN System Diagnosis
Test Mode C (see page 22-95) if the system does
not stop or turn off. Go to Test Mode D (see page
22-96) if the system does not run or turn on.
 Exterior lights
 Turn signals
 Entry light control
 Interior lights
 Horn (security and panic)
 Wiper/washer
If the problem is related to one of the following
items, go to the troubleshooting for that individual
system.  Gauge control module
 Door-open and trunk-open indicators
 Chimes (key-in, seat belt, lights-on, and parking brake)
Security
 Keyless entry
Keyinterlock
 Dash light brightness control
 Audio system
 Navigation (if equipped)
 HandsFreeLink (if equipped)
5. Record all DTCs, and sort them by DTC type.
6. Troubleshoot the DTC(s) in this order:  Battery voltage DTCs.
 Internal error DTCs.
 Loss of communication DTCs. Begintroubleshooting with the lowest number first
(Example: if DTC B1008 and B1011 are retrieved,
begin by troubleshooting B 1008).
 Signal error DTCs. Do this diagnosis if any of the control units are not
communicating (Not Available is displayed in the HDS)
as found by the B-CAN System Diagnosis Test Mode A
(see page 22-93).
1. Using the HDS, select the system that has the symptom from the BODY ELECTRICAL menu.
2. Select DTCs, and then check for loss of communication DTCs.
Go to step 3.
Replace the MICU.
3. Do the input test for the unit not communicating with the HDS.
MICU (see page 22-109)
Gauge control module (see page 22- 271)
Immobilizer-keyless control unit (see page
22-330)
Climate control unit (see page 21-24)
HandsFreeLink control unit (see page 23-388)
Are any DTCs indicated?
Ar e any l oss of communi cat i on DT Cs i nd i cat ed ?
08/08/21 14:24:59 61SNR030_220_0096
ProCarManuals.com
DYNOMITE -2009-

(#')
µ
µ
µ
µ
YES
NO
YES
NOUnit not communicating
22-9422-94Multiplex Integrated Control System
Troubleshooting - B-CAN System
Diagnosis Test Mode A (cont’d)
Troubleshooting - B-CAN System
Diagnosis Test Mode B
4. Select the system that has the problem from the
BODY ELECTRICAL menu, then select DTCs.
Go to step 5.
If the problem is related to one of the
following items, go to B-CAN System Diagnosis
Test Mode C (see page 22-95) if the system does
not stop or turn off. Go to Test Mode D (see page
22-96) if the system does not run or turn on.
 Exterior lights
 Turn signals
 Entry light control
 Interior lights
 Horn (security and panic)
 Wiper/washer
If the problem is related to one of the following
items, go to the troubleshooting for that individual
system.  Gauge control module
 Door-open and trunk-open indicators
 Chimes (key-in, seat belt, lights-on, and parking brake)
Security
 Keyless entry
Keyinterlock
 Dash light brightness control
 Audio system
 Navigation (if equipped)
 HandsFreeLink (if equipped)
5. Record all DTCs, and sort them by DTC type.
6. Troubleshoot the DTC(s) in this order:  Battery voltage DTCs.
 Internal error DTCs.
 Loss of communication DTCs. Begintroubleshooting with the lowest number first
(Example: if DTC B1008 and B1011 are retrieved,
begin by troubleshooting B 1008).
 Signal error DTCs. Do this diagnosis if any of the control units are not
communicating (Not Available is displayed in the HDS)
as found by the B-CAN System Diagnosis Test Mode A
(see page 22-93).
1. Using the HDS, select the system that has the symptom from the BODY ELECTRICAL menu.
2. Select DTCs, and then check for loss of communication DTCs.
Go to step 3.
Replace the MICU.
3. Do the input test for the unit not communicating with the HDS.
MICU (see page 22-109)
Gauge control module (see page 22- 271)
Immobilizer-keyless control unit (see page
22-330)
Climate control unit (see page 21-24)
HandsFreeLink control unit (see page 23-388)
Are any DTCs indicated?
Ar e any l oss of communi cat i on DT Cs i nd i cat ed ?
08/08/21 14:24:59 61SNR030_220_0096
ProCarManuals.com
DYNOMITE -2009-

Î(#')
22-100Multiplex Integrated Control System
Circuit Diagram
K5
G3 Q1 Q9
D2
LT BLU RED
No. 22 (7.5 A)
BLK
G501 T34
G602E6
BLK SG
G601E33
BLK
PG
H2
H1 Q6
B-CAN
MICU
G401 PNK
K4 G2
UNDER-DASH FUSE/RELAY BOX
UNDER-HOOD FUSE/RELAY BOX
WHTBRN
No. 10 (7.5 A)
BLK F20
No. 2 (IG) (50 A)
ORNIG1
BAT
BLU
WHT
No. 23 (10 A)
BATTERY
IGNITION SWITCH
No. 1 (BAT) (100 A)
MICU
SERVICE
CHECK
CONNECTOR IG1 HOT in ON (II)
and START (III)
CEILING
LIGHT
H1
D4 D2
LT BLU K-LINEQ8





 AUDIO UNIT*6
NAVIGATION
UNIT*5
DATA LINK
CONNECTOR
IMMOBILIZER-
KEYLESS
CONTROL UNIT
SRS UNIT
TPMS CONTROL
UNIT*3
ABS
MODULATOR-
CONTROL UNIT *1 EPS CONTROL
UNIT
VSA MODULATOR-
CONTROL UNIT *2 IG1
LT BLU
LT BLU F14
F28VBU
16
G501 BLK
1
18
PNK
No. 35 (7.5 A)
FUSE
(UNDER-DASH
FUSE/
RELAY BOX)
No. 23 (10 A)
FUSE
(UNDER-DASH
FUSE/
RELAY BOX)
15
PUR
WHT
HANDSFREELINK
CONTROL UNIT *4
(B-CAN)
PNK
PNK
(B-CAN)
08/08/21 14:25:00 61SNR030_220_0102
ProCarManuals.com
DYNOMITE -2009-

Î
µµ
µ
22-101







 124
19
1
RED
WHT CAN L
F-CAN TRANSCEIVER
CAN H
LT GRN
3
G504BLK
5
32
PNK
(B-CAN) (B-CAN) BRN/YELBRNLG
G101 BLK
7 2
IG1
YEL
VBU
B-CAN 1
4
PNK
16
BLK
G504 WHT
21
PNK GAUGE CONTROL MODULE (TACH)
BRN
WHT
17
18
MAIN CIRCUIT
B-CAN
TRANSCEIVER LCD DISPLAY
(DTC CODE DISPLAY)
IMMOBILIZER-KEYLESS
CONTROL UNIT
CLIMATE
CONTROL UNIT
No. 36 (10 A) FUSE
(UNDER-DASH
FUSE/RELAY BOX)
ABS MODULATOR-CONTROL UNIT*1
VSA MODURATOR-CONTROL UNIT*2
YAW RATE-LATERAL ACCELERATION
SENSOR*2
DATA LINK CONNECTOR
SRS UNIT
ECM/PCM
TPMS CONTROL UNIT*3
EPS CONTROL UNIT
WHT
: CAN line
No. 2 (15 A) FUSE
(UNDER-DASH
FUSE/RELAY BOX)
: Other communication line
*1: ’06 07 Touring and Premium models
*2: ’07 TYPE S and ’08 09 models
*3: ’08 09 models
*4: ’09 model with navigation system
*5: With navigation system
*6: Without navigation system
BLK*2
PNK
PNK
08/08/21 14:25:01 61SNR030_220_0103
ProCarManuals.com
DYNOMITE -2009-

(#' .
)

µ
µ
µ
µ µ
µ
DTC B1000:
YES
NO
YES
NO Control Unit Connector
YES
NO Control Unit Appropriate Connector
22-102Multiplex Integrated Control System
DTC Troubleshooting
Communication Bus Line Error
(BUS-OFF)
NOTE: If you are troubleshooting multiple DTCs, be
sure to follow the instructions in B-CAN System
Diagnosis Test Mode A (see page 22-93).
1. Clear the DTCs with the HDS.
2. Turn the ignition switch to LOCK (0), and then back to ON (II).
3. Wait for at least 6 seconds.
4. Check for DTCs with the HDS.
Go to step 5.
Intermittent failure, the communication bus
line is OK at this time. Check for loose or poor
connections, or worn/shorted wires. If the
connections are good, check the battery condition
(see page 22-67) and the charging system.
5. Check for DTCs with the HDS.
Go to step 6.
Faulty MICU; replace the under-dash fuse/
relay box (see page 22-66). 6. Turn the ignition switch to LOCK (0).
7. Disconnect the appropriate connector at each
control unit in the table one at a time. Clear the
DTCs, then recheck for DTCs after each unit is
disconnected.
Gauge control
module (tach) 36P connector
Immobilizer-keyless
control unit 7P connector
Climate control unit 32P connector
HandsFreeLink
control unit 28P connector
Go to step 8.
Check the power and grounds to the control
unit that was disconnected when B1000 did not
reset. If OK, replace the control unit.
8. Disconnect all of the appropriate connectors for each of the units in the table.
Gauge control
module (tach) 36P connector
Immobilizer-keyless
control unit 7P connector
Climate control unit 32P connector
HandsFreeLink
control unit 28P connector
Is DTC B1000 indicated?
Ar e DT Cs B1008, B1011, and B1032 al soindicated? Is DT C B1000 indicated with each individual unit
d i sconnect ed ?
08/08/21 14:25:01 61SNR030_220_0104
ProCarManuals.com
DYNOMITE -2009-

(#' .
)µ
µ
DTC B1900:
YES
NO
22-108 Multiplex Integrated Control System
DTC Troubleshooting (cont’d)
Communication Bus Line Error
(Bus OFF)
NOTE: If you are troubleshooting multiple DTCs, be
sure to follow the instructions in B-CAN System
Diagnosis Test Mode A (see page 22-93).
1. Clear the DTCs with the HDS.
2. Turn the ignition switch to LOCK (0), and then back to ON (II).
3. Wait for at least 6 seconds.
4. Check for DTCs with the HDS.
Troubleshoot DTC B 1000.
If only DTC B1900 is present, replace the
immobilizer-keyless control unit. If no DTCs are
present, it’s an intermittent failure, the system is
OK at this time. Check for loose or poor
connections at the immobilizer control unit 7P
connector, and at under-dash fuse/relay box
connector Q (16P).
Ar e DT Cs B1000, B1008, B1011, and B1032 also ind icated w ith DT C B1900?
08/08/21 14:25:02 61SNR030_220_0110
ProCarManuals.com
DYNOMITE -2009-

Î
(#')
22-112Keyless/Power Door Locks/Security System
Component Location Index
NAVIGATION UNIT or
AUDIO UNIT
IMMOBILIZER-KEYLESS
CONTORL UNIT
(With built-in receiver)
SECURITY INDICATOR GAUGE CONTORL MODULE
(SPEEDO)
HEADLIGHT
HOOD SWITCH
MICU
(Built into the under-
dash fuse/relay box)
HORN
TRANSMITTER
LOCK BUTTON TRUNK BUTTON
UNLOCK BUTTON
IGNITION KEY PANIC BUTTONSymptom Troubleshooting,
page 22-126
Replacement, page 22-332
Replacement, page 22-174
Adjustment, page 22-173
Bulb Replacement, page 22-177
Test, page 22-141
Input Test, page 22-131
Test/Replacement, page 22-146
Test/Replacement, page 22-142
08/08/21 14:25:04 61SNR030_220_0114
ProCarManuals.com
DYNOMITE -2009-