(#'
)
µ
µ
µ
µ µ
µ
µ
µ
YES
NO
YES
NO
YES
NO
YES
NO
DTC P0761:
14-13314-133
13. Check for Temporary DTCs or DTCs with the HDS.
Go to step 8.
Go to step 14.
14. Monitor the OBD STATUS for P0756 or P0757 in the DTCs MENU with the HDS.
Troubleshooting is complete. If any other
Temporary DTCs or DTCs were indicated in step 13,
go to the indicated DTC’s troubleshooting.
If the HDS indicates FAILED, go to step 8. If
the HDS indicates NOT COMPLETED, go to step 12. NOTE: Before you troubleshoot, record all freeze data
and any on-board snapshot with the HDS, and review
General Troubleshooting Information (see page 14-3).
1. Warm up the engine to normal operating temperature (the radiator fan comes on).
2. Make sure that the transmission is filled to the proper level, and check for fluid leaks.
3. Drain the ATF (see step 3 on page 14-232) through a strainer. Inspect the strainer for metal debris or
excessive clutch material.
Replace the transmission, then go to step 12.
Replace the ATF (see page 14-232), then go to
step 4.
4. Turn the ignition switch to ON (II).
5. Clear the DTC with the HDS.
6. Test-drive the vehicle with the shift lever in D, and let the transmission shift through all five gears.
7. Monitor the OBD STATUS for P0761 in the DTCs MENU with the HDS.
Go to step 8.
If the HDS indicates PASSED, intermittent
failure, the system is OK at this time. If the HDS
indicates NOT COMPLETED, go to step 6.
8. Clear the DTC with the HDS.
(cont’d)Shift Solenoid Valve C Stuck OFF
I s DT C P07 5 6 or P07 5 7 i nd i cat ed ?Does the HDS ind icate PASSED? Does t he st r ai ner hav e met al d ebr i s or ex cessi v eclutch mater ial?
Does the HDS ind icate F AILED?
08/08/21 14:42:32 61SNR030_140_0135
ProCarManuals.com
DYNOMITE -2009-
(#'
)
µ
µ
µ
µ µ
µ
µ
µ
DTC P0771:
YES
NO
YES
NO YES
NO
YES
NO
14-135
Shift Solenoid Valve E Stuck OFF
NOTE: Before you troubleshoot, record all freeze data
and any on-board snapshot with the HDS, and review
General Troubleshooting Information (see page 14-3).
1. Warm up the engine to normal operating temperature (the radiator fan comes on).
2. Make sure that the transmission is filled to the proper level, and check for fluid leaks.
3. Drain the ATF (see step 3 on page 14-232) through a strainer. Inspect the strainer for metal debris or
excessive clutch material.
Replace the transmission, then go to step 12.
Replace the ATF (see page 14-232), then go to
step 4.
4. Turn the ignition switch to ON (II).
5. Clear the DTC with the HDS.
6. Test-drive the vehicle with the shift lever in D, and let the transmission shift through all five gears.
7. Monitor the OBD STATUS for P0771 in the DTCs MENU with the HDS.
Go to step 8.
If the HDS indicates PASSED, intermittent
failure, the system is OK at this time. If the HDS
indicates NOT COMPLETED, go to step 6.
8. Clear the DTC with the HDS. 9. Select Shift Solenoid Valve E in the Miscellaneous
Test Menu, and check that shift solenoid valve E
operates with the HDS.
Go to step 10.
Replace shift solenoid valve E (see page
14-217), then go to step 12.
10. Test-drive the vehicle with the shift lever in D, and let the transmission shift through all five gears.
11. Monitor the OBD STATUS for P0771 in the DTCs MENU with the HDS.
Repair shift valve E, or replace the
transmission, then go to step 12.
If the HDS indicates PASSED, intermittent
failure, the system is OK at this time. If the HDS
indicates NOT COMPLETED, go to step 10.
12. Test-drive the vehicle with the shift lever in D, and let the transmission shift through 1st to 3rd gears,
then drive the vehicle at speeds over 19 mph
(30 km/h) for at least 20 seconds.
(cont’d)
Does t he st r ai ner hav e met al d ebr i s or ex cessi v eclutch mater ial?
Does the HDS ind icate F AILED? Is a clicking sound heard?
Does the HDS ind icate F AILED?
08/08/21 14:42:32 61SNR030_140_0137
ProCarManuals.com
DYNOMITE -2009-
(#'
)
µ
µ
µ
µ
µ
µ
µ
µ
YES
NO
YES
NO
YES
NO
YES
NO
DTC P0776:
DTC P0777:
14-13614-136Automatic Transmission
DTC Troubleshooting (cont’d)
13. Check for Temporary DTCs or DTCs with the HDS.
Go to step 8.
Go to step 14.
14. Monitor the OBD STATUS for P0771 in the DTCs MENU with the HDS.
Troubleshooting is complete. If any other
Temporary DTCs or DTCs were indicated in step 13,
go to the indicated DTC’s troubleshooting.
If the HDS indicates FAILED, go to step 8. If
the HDS indicates NOT COMPLETED, go to step 12. NOTE: Before you troubleshoot, record all freeze data
and any on-board snapshot with the HDS, and review
General Troubleshooting Information (see page 14-3).
1. Warm up the engine to normal operating temperature (the radiator fan comes on).
2. Make sure that the transmission is filled to the proper level, and check for fluid leaks.
3. Drain the ATF (see step 3 on page 14-232) through a strainer. Inspect the strainer for metal debris or
excessive clutch material.
Replace the transmission, then go to step 13.
Replace the ATF (see page 14-232), then go to
step 4.
4. Turn the ignition switch to ON (II).
5. Clear the DTC with the HDS.
6. Test-drive the vehicle with the shift lever in D, and let the transmission shift through all five gears.
7. Monitor the OBD STATUS for P0776 or P0777 in the DTCs MENU with the HDS.
Go to step 8.
If the HDS indicates PASSED, intermittent
failure, the system is OK at this time. If the HDS
indicates NOT COMPLETED, go to step 6.
8. Clear the DTC with the HDS.A/T Clutch Pressure Control
Solenoid Valve B Stuck OFF
A/T Clutch Pressure Control
Solenoid Valve B Stuck ON
Is DTC P0771 indicated?
Does the HDS ind icate PASSED? Does t he st r ai ner hav e met al d ebr i s or ex cessi v eclutch mater ial?
Does the HDS ind icate F AILED?
08/08/21 14:42:33 61SNR030_140_0138
ProCarManuals.com
DYNOMITE -2009-
(#'
)
µ
µ
µ
µ µ
µ
µ
µ
DTC P0796:
DTC P0797:
YES
NO
YES
NO YES
NO
YES
NO
14-139
A/T Clutch Pressure Control
Solenoid Valve C Stuck OFF
A/T Clutch Pressure Control
Solenoid Valve C Stuck ON
NOTE: Before you troubleshoot, record all freeze data
and any on-board snapshot with the HDS, and review
General Troubleshooting Information (see page 14-3).
1. Warm up the engine to normal operating temperature (the radiator fan comes on).
2. Make sure that the transmission is filled to the proper level, and check for fluid leaks.
3. Drain the ATF (see step 3 on page 14-232) through a strainer. Inspect the strainer for metal debris or
excessive clutch material.
Replace the transmission, then go to step 13.
Replace the ATF (see page 14-232), then go to
step 4.
4. Turn the ignition switch to ON (II).
5. Clear the DTC with the HDS.
6. Test-drive the vehicle with the shift lever in D, and let the transmission shift through all five gears.
7. Monitor the OBD STATUS for P0796 or P0797 in the DTCs MENU with the HDS.
Go to step 8.
If the HDS indicates PASSED, intermittent
failure, the system is OK at this time. If the HDS
indicates NOT COMPLETED, go to step 6.
8. Clear the DTC with the HDS. 9. Select Clutch Pressure Control (Linear) Solenoid
Valve C in the Miscellaneous Test Menu, and test
A/T clutch pressure control solenoid valve C with
the HDS.
Intermittent failure, the system is OK at this
time.
Follow the instructions indicated on the HDS
according to the test result, if the HDS has not
determined the cause of the failure, go to step 10. If
any part was replaced, go to step 11.
10. Inspect A/T clutch pressure control solenoid valve C (see page 14-224).
Repair the hydraulic system related to shift
valves B and C, or replace the transmission, then
go to step 13.
Replace A/T clutch pressure control solenoid
valve C (see page 14-226), then go to step 11.
11. Turn the ignition switch to ON (II).
12. Clear the DTC with the HDS.
13. Test-drive the vehicle with the shift lever in D, and let the transmission shift through all five gears.
(cont’d)
Does t he st r ai ner hav e met al d ebr i s or ex cessi v eclutch mater ial?
Does the HDS ind icate F AILED? Does the HDS ind icate NORMAL?
Does A/ T cl ut ch pr essur e cont r ol sol enoi d v al v e Cw or k pr oper l y ?
08/08/21 14:42:33 61SNR030_140_0141
ProCarManuals.com
DYNOMITE -2009-
(#'
)
µ
µ
µ
µ µ
µ
µ
µ
YES
NO
YES
NO
YES
NO
YES
NO
DTC P1730:
14-19514-195
16. Reconnect all connectors.
17. Update the PCM if it does not have the latest
software (see page 11-227), or substitute a known-
good PCM (see page 11-7).
18. Start the engine with the shift lever in P. Shift to N, then shift to R while pressing the brake pedal, and
wait for at least 2 seconds.
19. Check for Temporary DTCs or DTCs with the HDS.
Check for poor connections or loose
terminals between the transmission range switch
and the PCM. If the PCM was updated, substitute a
known-good PCM (see page 11-7), then go to step
18. If the PCM was substituted, go to step 1.
Go to step 20.
20. Monitor the OBD STATUS for P1717 in the DTCs MENU with the HDS.
If the PCM was updated, troubleshooting is
complete. If the PCM was substituted, replace the
original PCM (see page 11-228). If any other
Temporary DTCs or DTCs were indicated in step 19,
go to the indicated DTC’s troubleshooting.
If the HDS indicates FAILED, check for poor
connections or loose terminals between the
transmission range switch and the PCM. If the PCM
was updated, substitute a known-good PCM
(see page 11-7), then go to step 18. If the PCM was
substituted, go to step 1. If the HDS indicates NOT
COMPLETED, go to step 18. Shift Solenoid Valves A or D Stuck OFF
Shift Solenoid Valve B Stuck ON
Shift Valves A, B, or D Stuck
NOTE: Before you troubleshoot, record all freeze data
and any on-board snapshot with the HDS, and review
the General Troubleshooting Information (see page
14-3).
1. Warm up the engine to normal operating temperature (the radiator fan comes on).
2. Make sure that the transmission is filled to the proper level, and check for fluid leaks.
3. Drain the ATF (see step 3 on page 14-232) through a strainer. Inspect the strainer for metal debris or
excessive clutch material.
Replace the transmission, then go to step 14.
Replace the ATF (see page 14-232), then go to
step 4.
4. Turn the ignition switch to ON (II).
5. Clear the DTC with the HDS.
6. Test-drive the vehicle with the shift lever in D, and let the transmission shift through all five gears.
7. Monitor the OBD STATUS for P1730 in the DTCs MENU with the HDS.
Go to step 8.
If the HDS indicates PASSED, intermittent
failure, the system is OK at this time. If the HDS
indicates NOT COMPLETED, go to step 6.
8. Clear the DTC with the HDS.
(cont’d)Problem in Shift Control System:
I s DT C P 17 17 i nd i cat ed ?
Does the HDS ind icate PASSED? Does t he st r ai ner hav e met al d ebr i s or ex cessi v e
clutch mater ial?
Does the HDS ind icate F AILED?
08/08/21 14:45:29 61SNR030_140_0197
ProCarManuals.com
DYNOMITE -2009-
(#'
)
µ
µ
µ
µ µ
µ
µ
µ
µ
µ
DTC P1731:
YES
NO
YES
NO YES
NO
YES
NO
YES
NO
14-197
Problem in Shift Control System:
Shift Solenoid Valve E Stuck ON
Shift Valve E Stuck
A/T Clutch Pressure Control Solenoid Valve A Stuck
OFF
NOTE: Before you troubleshoot, record all freeze data
and any on-board snapshot with the HDS, and review
General Troubleshooting Information (see page 14-3).
1. Warm up the engine to normal operating temperature (the radiator fan comes on).
2. Make sure that the transmission is filled to the proper level, and check for fluid leaks.
3. Drain the ATF (see step 3 on page 14-232) through a strainer. Inspect the strainer for metal debris or
excessive clutch material.
Replace the transmission, then go to step 14.
Replace the ATF (see page 14-232), then go to
step 4.
4. Turn the ignition switch to ON (II).
5. Clear the DTC with the HDS.
6. Test-drive the vehicle with the shift lever in D, and let the transmission shift through all five gears.
7. Monitor the OBD STATUS for P0731 in the DTCs MENU with the HDS.
Go to step 8.
If the HDS indicates PASSED, intermittent
failure, the system is OK at this time. If the HDS
indicates NOT COMPLETED, go to step 6.
8. Clear the DTC with the HDS. 9. Select Shift Solenoid Valve E in the Miscellaneous
Test Menu, and check it operates with the HDS.
Go to step 10.
Replace shift solenoid valve E (see page
14-217), then go to step 14.
10. Select Clutch Pressure Control (Linear) Solenoid Valve A in the Miscellaneous Test Menu, and test
A/T clutch pressure control solenoid valve A with
the HDS.
Intermittent failure, the system is OK at this
time.
Follow the instructions indicated on the HDS
by the test result, but if the HDS has not determined
the cause of the failure, go to step 11. If any part
was replaced, go to step 12.
11. Inspect A/T clutch pressure control solenoid valve A (see page 14-219).
Repair the hydraulic system related with shift
valve E, or replace the transmission, then go to step
14.
Replace A/T clutch pressure control solenoid
valve A (see page 14-221), then go to step 12.
(cont’d)
Does t he st r ai ner hav e met al d ebr i s or ex cessi v eclutch mater ial?
Does the HDS ind icate F AILED? Is a clicking sound heard?
Does the HDS ind icate NORMAL?
Does A/ T cl ut ch pr essur e cont r ol sol enoi d v al v e Aoper at e pr oper l y ?
08/08/21 14:45:30 61SNR030_140_0199
ProCarManuals.com
DYNOMITE -2009-
(#'
)
µ
µ
µ
µ µ
µ
µ
µ
YES
NO
YES
NO
YES
NO
YES
NO
DTC P1732:
14-19814-198Automatic Transmission
DTC Troubleshooting (cont’d)
12. Turn the ignition switch to ON (II).
13. Clear the DTC with the HDS.
14. Test-drive the vehicle with the shift lever in D, and
let the transmission shift through all five gears.
15. Check for Temporary DTCs or DTCs with the HDS.
Go to step 8.
Go to step 16.
16. Monitor the OBD STATUS for P1731 in the DTCs MENU with the HDS.
Troubleshooting is complete. If any other
Temporary DTCs or DTCs were indicated in step 15,
go to the indicated DTC’s troubleshooting.
If the HDS indicates FAILED, go to step 8. If
the HDS indicates NOT COMPLETED, go to step 14. Shift Solenoid Valves B or C Stuck ON
Shift Valves B or C Stuck
NOTE: Before you troubleshoot, record all freeze data
and any on-board snapshot with the HDS, and review
General Troubleshooting Information (see page 14-3). 1. Warm up the engine to normal operating temperature (the radiator fan comes on).
2. Make sure that the transmission is filled to the proper level, and check for fluid leaks.
3. Drain the ATF (see step 3 on page 14-232) through a strainer. Inspect the strainer for metal debris or
excessive clutch material.
Replace the transmission, then go to step 13.
Replace the ATF (see page 14-232), then go to
step 4.
4. Turn the ignition switch to ON (II).
5. Clear the DTC with the HDS.
6. Test-drive the vehicle with the shift lever in D, and let the transmission shift through all five gears.
7. Monitor the OBD STATUS for P1732 in the DTCs MENU with the HDS.
Go to step 8.
If the HDS indicates PASSED, intermittent
failure, the system is OK at this time. If the HDS
indicates NOT COMPLETED, go to step 6.
8. Clear the DTC with the HDS.Problem in Shift Control System:
Is DTC P1731 indicated?
Does the HDS ind icate PASSED? Does t he st r ai ner hav e met al d ebr i s or ex cessi v eclutch mater ial?
Does the HDS ind icate F AILED?
08/08/21 14:45:30 61SNR030_140_0200
ProCarManuals.com
DYNOMITE -2009-
(#'
)
µ
µ
µ
µ µ
µ
µ
µ
µ
µ
DTC P1733:
YES
NO
YES
NO YES
NO
YES
NO
YES
NO
14-200
Automatic Transmission
DTC Troubleshooting (cont’d)
Problem in Shift Control System:
Shift Solenoid Valve D Stuck ON
Shift Valve D Stuck
A/T Clutch Pressure Control Solenoid Valve C Stuck
OFF
NOTE: Before you troubleshoot, record all freeze data
and any on-board snapshot with the HDS, and review
General Troubleshooting Information (see page 14-3).
1. Warm up the engine to normal operating temperature (the radiator fan comes on).
2. Make sure that the transmission is filled to the proper level, and check for fluid leaks.
3. Drain the ATF (see step 3 on page 14-232) through a strainer. Inspect the strainer for metal debris or
excessive clutch material.
Replace the transmission, then go to step 14.
Replace the ATF (see page 14-232), then go to
step 4.
4. Turn the ignition switch to ON (II).
5. Clear the DTC with the HDS.
6. Test-drive the vehicle with the shift lever in D, and let the transmission shift through all five gears.
7. Monitor the OBD STATUS for P1733 in the DTCs MENU with the HDS.
Go to step 8.
If the HDS indicates PASSED, intermittent
failure, the system is OK at this time. If the HDS
indicates NOT COMPLETED, go to step 6.
8. Clear the DTC with the HDS. 9. Select Shift Solenoid Valve D in the Miscellaneous
Test Menu, and check it operates with the HDS.
Go to step 10.
Replace shift solenoid valve D (see page
14-217), then go to step 14.
10. Select Clutch Pressure Control (Linear) Solenoid Valve C in the Miscellaneous Test Menu, and test
A/T clutch pressure control solenoid valve C with
the HDS.
Intermittent failure, the system is OK at this
time.
Follow the instructions indicated on the HDS
according to the test result, but if the HDS has not
determined the cause of the failure, go to step 11. If
any part was replaced, go to step 12.
11. Inspect A/T clutch pressure control solenoid valve C (see page 14-224).
Repair the hydraulic system related with shift
valve D, or replace the transmission, then go to
step 14.
Replace A/T clutch pressure control
solenoid valve C (see page 14-226), then go to step
12.
Does t he st r ai ner hav e met al d ebr i s or ex cessi v e clutch mater ial?
Does the HDS ind icate F AILED? Is a clicking sound heard?
Does the HDS ind icate NORMAL?
Does A/ T cl ut ch pr essur e cont r ol sol enoi d v al v e Coper at e pr oper l y ?
08/08/21 14:45:30 61SNR030_140_0202
ProCarManuals.com
DYNOMITE -2009-