2006 ACURA CSX check engine

Î
Without the HDS
11-323
A
B C
E
D
A
14. Disconnect the quick-connect fitting (A): Hold the
connector (B) with one hand, and squeeze the
retainer tabs (C) with the other hand to release
them from the locking tabs (D). Pull the connector
off.
NOTE: Be careful not to damage the line (E) or other parts.
 Do not use tools.
 If the connector does not move, keep the retainer tabs pressed down, and alternately pull and push
the connector until it comes off easily.
 Do not remove the retainer from the line; once removed, the retainer must be replaced with a
new one.
15. After disconnecting the quick-connect fitting, check it for dirt or damage (see step 4 on page 11-330).
16. Do the battery terminal reconnection procedure (see page 22-68). 1. Remove the under-dash fuse/relay box (see page
22-66), then remove PGM-Fl main relay 2 (FUEL
PUMP) (A) from the under-dash fuse/relay box.
2. Reinstall the under-dash fuse/relay box.
3. Start the engine, and let it idle until it stalls. NOTE: If any DTCs are stored, clear and ignore
them.
4. Turn the ignition switch to LOCK (0).
5. Remove the fuel fill cap.
6. Do the battery terminal disconnection procedure (see page 22-68).
(cont’d)
08/08/21 14:29:48 61SNR030_110_0323
ProCarManuals.com
DYNOMITE -2009-

µµ µ

(#') (#'
!)
 Special Tools Required
11-32511-325
Fuel Pressure Test Fuel Tank Draining
07406-004000B
07AAJ-S6MA150
 Fuel pressure gauge 07406-004000B
 Fuel pressure gauge attachment set 07AAJ-S6MA150 1. Relieve the fuel pressure (see page 11-322).
2. Disconnect the quick-connect fitting. Attach the fuel pressure gauge set and the fuel pressure gauge.
3. Start the engine, and let it idle.  If the engine starts, go to step 5.
 If the engine does not start, go to step 4.
4. Check to see if the fuel pump is running: Listen to the fuel filler port with the fuel fill cap removed.
The fuel pump should run for 2 seconds when the
ignition switch is first turned on.
 If the pump runs, go to step 5.
 If the pump does not run, do the fuel pump circuit troubleshooting (see page 11- 318).
5. Read the fuel pressure gauge. The pressure should be 330 380 kPa (3.4 3.9 kgf/cm , 48 55 psi).
 If the pressure is OK, the test is complete.
 If the pressure is out of specification, replace the fuel pressure regulator (see page 11-337) and the
fuel filter (see page 11-337), then recheck the fuel
pressure. 1. Remove the fuel tank unit (see page 11-334).
2. Using a hand pump, a hose, and a container
suitable for fuel, draw the fuel from the fuel tank.
3. Reinstall the fuel tank unit (see page 11-335).
2
08/08/21 14:29:49 61SNR030_110_0325
ProCarManuals.com
DYNOMITE -2009-





(#'
 )
11-329
Fuel Line/Quick-Connect Fitting Removal
A
AA
A AA
A B
D
C
NOTE: Before you work on the fuel lines and fittings,
read the Fuel Line/Quick-Connect Fitting Precautions
(see page 11-328).
1. Relieve the fuel pressure (see page 11-322).
2. Check the fuel quick-connect fittings (A) for dirt, and clean them if needed.
3. Place a rag or shop towel over the quick-connectfitting. Hold the connector (A) with one hand, and
squeeze the retainer tabs (B) with the other hand to
release them from the locking tabs (C). Pull the
connector off.
NOTE: Be careful not to damage the line (D) or other parts.
 Do not use tools.
 If the connector does not move, keep the retainer tabs pressed down, and alternately pull and push
the connector until it comes off easily.
 Do not remove the retainer from the line; once removed, the retainer must be replaced with a
new one.
(cont’d)
* : This illustration shows K20Z2 engine.
08/08/21 14:29:53 61SNR030_110_0329
ProCarManuals.com
DYNOMITE -2009-


Î
Î
Î
(#'
 )
11-331
Fuel Line/Quick-Connect Fitting Installation
A B
B A A
A
B
A
B
A
B
NOTE: Before you work on the fuel lines and fittings,
read the Fuel Line/Quick-Connect Fitting Precautions
(see page 11-328). 1. Check the contact area (A) of the line (B) for dirt or damage, and clean it if needed.
2. Insert a new retainer (A) into the connector (B) if the retainer is damaged, or after:
 replacing the fuel rail.
 replacing the fuel feed line.
 replacing the fuel pump.
 replacing the fuel filter.
 replacing the fuel gauge sending unit.
 replacing the EVAP purge pipe.
 replacing the EVAP canister.
 replacing the fuel tank.
 replacing the fuel fill pipe.
 removing the retainer from the line.
 Use the same manufacturer’s retainer and the same size when replacing the retainer (see page
11-328). 3. Before connecting a new fuel tube/quick-connect
fitting assembly (A), remove the old retainer (B)
from the mating line.
(cont’d)
* : This illustration shows K20Z2 engine.
08/08/21 14:30:55 61SNR030_110_0331
ProCarManuals.com
DYNOMITE -2009-


(#'
 )

(#'
 )
11-33711-337
Fuel Pressure Regulator
Replacement Fuel Filter Replacement
A
B
C
D A
D B
C D
B
1. Remove the fuel tank unit (see page 11-334).
2. Remove the bracket (A).
3. Remove the ground ring (B).
4. Remove the fuel pressure regulator (C).
5. Install the parts in the reverse order of removal with new O-rings (D) and a new bracket (A). When
installing the fuel tank unit, align the marks on the
unit and the fuel tank (see page 11-335).
NOTE: Coat the O-rings with clean engine oil; do
not use any other oil.
Do not pinch the O-rings during installation. The fuel filter should be replaced when
ever the fuel
pressure drops below the specified value (see page
11-325), after making sure that the fuel pump and the
fuel pressure regulator are OK.
1. Remove the fuel tank unit (see page 11-334).
2. Remove the fuel filter set (A).
3. Check these items before installing the fuel tank unit:
 When connecting the wire harness, make sure the connection is secure and the connectors (B)
are firmly locked into place.
 When installing the fuel gauge sending unit (C), make sure the connection is secure and the
connector is firmly locked into place. Be careful
not to bend or twist it excessively.
4. Install the parts in the reverse order of removal with new O-rings (D). When installing the fuel tank
unit, align the marks on the unit and the fuel tank
(see page 11-335).
08/08/21 14:31:00 61SNR030_110_0337
ProCarManuals.com
DYNOMITE -2009-



(#'
)
Carbon Accumulation Check Throttle Position Learning Check
11-343
Throttle Body Test
A A
NOTE: If the malfunction indicator lamp (MIL) has been
reported on, check for diagnostic trouble code (DTCs).
1. Connect the HDS to the data link connector (DLC) (A) located under the driver’s side of the dashboard.
2. Turn the ignition switch to ON (II).
3. Make sure the HDS communicates with the ECM/ PCM. If it doesn’t, go to the DLC circuit
troubleshooting (see page 11- 204).
4. Start the engine. Hold the engine speed at 3,000 rpm without load (A/T in P or N, M/T in
neutral) until the radiator fan comes on, then let it
idle.
5. Check the REL TP SENSOR in the DATA LIST with the HDS. The reading should be below 2.46 deg. If it
is not, clean the throttle body (see page 11- 344).NOTE: If the malfunction indicator lamp (MIL) has been
reported on, check for diagnostic trouble code (DTCs).
1. Connect the HDS to the data link connector (DLC) (A) located under the driver’s side of the dashboard.
2. Turn the ignition switch to ON (II).
3. Make sure the HDS communicates with the ECM/ PCM. If it doesn’t, go to the DLC circuit
troubleshooting (see page 11-204).
4. Select the INSPECTION MENU with the HDS.
5. Do the TP POSITION CHECK in the ETCS TEST. If needed, clean the throttle body (see page 11-344).
08/08/21 14:31:07 61SNR030_110_0343
ProCarManuals.com
DYNOMITE -2009-


(#'
!) µ

(#') Special Tools Required
11-34411-344 Intake Air System
Throttle Body Cleaning
Intake Air Bypass Control Thermal
Valve Test
A A A
B
Do not insert your fingers into the installed throttle
body when you turn the ignition switch to ON (II) or
while the ignition switch is ON (II). If you do, you
will seriously injure your fingers if the throttle valve
is activated.
1. Check for damage to the air cleaner. If the air cleaner element is damaged, replace it (see page
11-346).
2. Remove the throttle body; K20Z2 engine (see page 11-348), K20Z3 engine (see page 11-349).
3. Clean off the carbon from the throttle valve and inside the throttle body with a paper towel soaked
in throttle plate and induction cleaner.
NOTE: Remove the throttle body to clean it.
 Be careful not to pinch your fingers.
 To avoid removing the molybdenum coating, do not clean the bearing area of the throttle shaft (A).
 Do not spray throttle plate and induction cleaner directly on the throttle body.
 Use Honda genuine throttle plate and induction cleaner.
4. Install the throttle body (see page 11- 348).
5. Reset the ECM/PCM with the HDS (see page 11-4).
6. Turn the ignition switch to ON (II), and wait 2 seconds.
7. Do the ECM/PCM idle learn procedure (see page 11-310). Vacuum pump/gauge, 0 30 in.Hg, Snap-on YA4000A
or equivalent, commercially available
1. Start the engine, then let it idle. NOTE: The engine coolant temperature must be
below 65 °C (149 °F).
2. Remove the engine cover (see step 1 on page 9-3).
3. Remove the vacuum hose (A) from the intake air duct, and connect a vacuum pump/gauge (B) to the
hose.
4. Raise and lower the engine speed, and make sure the vacuum gauge reading changes as the engine
speed changes.
If the vacuum reading does not change, check for
these problems:
 Misrouted, leaking, broken, or clogged intake air bypass control system vacuum lines.
 A cracked or damaged intake air bypass control thermal valve. Replace the valve if needed
(see page 11-351).
5. Hold the engine speed at 3,000 rpm without load (A/T in P or N, M/T in neutral) until the radiator fan
comes on, then let it idle.
* : This illustration shows K20Z2 engine.
08/08/21 14:31:08 61SNR030_110_0344
ProCarManuals.com
DYNOMITE -2009-


(#'

 )
11-34511-345
Air Cleaner Removal/Installation
C B
12 N·m
(1.2 kgf·m,
8.7 lbf·ft)
A
6. Raise and lower the engine speed, and make sure the vacuum gauge reading does not change as the
rpm changes.
If the vacuum reading changes, check for these
problems:
 Misrouted, leaking, broken, or clogged intake air bypass control system vacuum lines.
 A cracked or damaged intake air bypass control thermal valve. Replace the valve if needed
(see page 11-351). 1. Disconnect the MAF sensor/IAT sensor 5P
connector (A).
2. Remove the bolts (B).
3. Remove the air cleaner (C).
4. Install the parts in the reverse order of removal.
* : This illustration shows K20Z2 engine.
08/08/21 14:31:08 61SNR030_110_0345
ProCarManuals.com
DYNOMITE -2009-