µ
µ µ
µ
YES
NO YES
NO
11-305
SG6 (BLK)
ECM/PCM CONNECTOR A (44P) A/C PRESSURE SENSOR 3P CONNECTOR
SG6 (BLK)
18. Turn the ignition switch to LOCK (0).
19. Jump the SCS line with the HDS.
20. Disconnect ECM/PCM connector A (44P).
21. Check for continuity between A/C pressure sensor3P connector terminal No. 3 and ECM/PCM
connector terminal A9.
Go to step 32.
Repair open in the wire between the ECM/
PCM (A9) and the A/C pressure sensor, then go to
step 24. 22. Turn the ignition switch to LOCK (0).
23. Replace the A/C pressure sensor (see page 21-8).
24. Reconnect all connectors.
25. Turn the ignition switch to ON (II).
26. Reset the ECM/PCM with the HDS.
27. Do the ECM/PCM idle learn procedure (see page
11-310).
28. Start the engine, and let it idle.
29. Turn the blower switch on.
30. Turn the A/C switch on.
31. Check for Temporary DTCs or DTCs with the HDS.
Check for poor connections or loose
terminals at the A/C pressure sensor and the ECM/
PCM, then go to step 1.
Troubleshooting is complete. If any other
Temporary DTCs or DTCs are indicated, go to the
indicated DTC’s troubleshooting.
32. Reconnect all connectors.
33. Update the ECM/PCM if it does not have the latest software (see page 11-227), or substitute a known-
good ECM/PCM (see page 11-7).
34. Start the engine, and let it idle.
35. Turn the blower switch on.
36. Turn the A/C switch on.
(cont’d)
Wire side of female terminalsTerminal side of female terminals
Is there continuity? Is DT C P0533 ind icated ?
08/08/21 14:29:36 61SNR030_110_0305
ProCarManuals.com
DYNOMITE -2009-
(#'
)
µ
µµ µ
µ
µ
µ
µ
YES
NO YES
NO
YES
NO
YES
NO
11-30611-306Idle Control System
DTC Troubleshooting (cont’d) A/C Signal Circuit Troubleshooting
37. Check for Temporary DTCs or DTCs with the HDS.
Check for poor connections or loose
terminals at the A/C pressure sensor and the ECM/
PCM. If the ECM/PCM was updated, substitute a
known-good ECM/PCM (see page 11-7), then go to
step 34. If the ECM/PCM was substituted, go to step
1.
If the ECM/PCM was updated, troubleshooting
is complete. If the ECM/PCM was substituted,
replace the original ECM/PCM (see page 11-228). If
any other Temporary DTCs or DTCs are indicated,
go to the indicated DTC’s troubleshooting. 1. Start the engine, and let it idle.
2. Turn the blower switch on.
3. Turn the A/C switch on.
4. Check the A/C CLUTCH in the DATA LIST with the
HDS.
Go to step 5.
Do the A/C system test (see page 21-99).
5. Check the A/C system.
The air conditioning system circuit is OK.
Go to step 6.
6. Turn the ignition switch to LOCK (0).
7. Turn the ignition switch to ON (II).
8. Activate the A/C CLUTCH in the INSPECTION MENU with the HDS.
Do the A/C system test (see page 21-99).
Go to step 9.
9. Turn the ignition switch to LOCK (0).
10. Jump the SCS line with the HDS.
11. Disconnect ECM/PCM connector A (44P).
12. Turn the ignition switch to ON (II).
Is DT C P0533 ind icated ?
Does it indicate ON?
Does t he A/ C sy st em oper at e?
I s t her e a cl i ck i ng noi se f r om t he A/ C compr essorclutch?
08/08/21 14:29:36 61SNR030_110_0306
ProCarManuals.com
DYNOMITE -2009-
(#'
)
µ
µ µ
µ
µ
µ
YES
NO
YES
NO
YES
NO
11-30711-307
Alternator FR Signal Circuit
Troubleshooting
ECM/PCM CONNECTOR A (44P)
ACC (RED)JUMPER WIRE
ECM/PCM CONNECTOR B (44P)ALTF
(WHT/RED)
13. Momentarily connect ECM/PCM connector terminalA14 to body ground with a jumper wire s everal
times.
Update the ECM/PCM if it does not have the
latest software (see page 11-227), or substitute a
known-good ECM/PCM (see page 11-7), then
recheck. If the symptom/indication goes away with
a known-good ECM/PCM, replace the original ECM/
PCM (see page 11-228).
Check for poor connections or loose terminals
attheA/CclutchrelayandtheECM/PCM.Ifthe
connections and the terminals are OK, check the
A/C compressor clutch relay (see page 22-70),
repair open in the wires between the ECM/PCM
(A14), the A/C compressor clutch relay, and other
A/C systems parts. 1. Start the engine, and let it idle.
2. Monitor the ALTERNATOR in the DATA LIST with
the HDS.
3. Check if the indicated percentage varies when the headlight switch is turned on.
The alternator signal circuit is OK.
Go to step 4.
4. Turn the headlight switch and ignition switch to LOCK (0).
5. Jump the SCS line with the HDS.
6. Disconnect the alternator 4P connector.
7. Disconnect ECM/PCM connector B (44P).
8. Check for continuity between body ground and ECM/PCM connector terminal B43.
Repair short in the wire between the ECM/
PCM (B43) and the alternator.
Update the ECM/PCM if it does not have the
latest software (see page 11-227), or substitute a
known-good ECM/PCM (see page 11-7), then
recheck. If the symptom/indication goes away with
a known-good ECM/PCM, replace the original ECM/
PCM (see page 11-228).
Terminal side of female terminals
Terminal side of female terminals
I s t her e a cl i ck i ng noi se f r om t he A/ C compr essorclutch? Does t he per cent age v ar y ?
Is there continuity?
08/08/21 14:29:37 61SNR030_110_0307
ProCarManuals.com
DYNOMITE -2009-
(#'
)
µ
µ µ
µ
µ
µ
YES
NO
YES
NO
YES
NO
11-30711-307
Alternator FR Signal Circuit
Troubleshooting
ECM/PCM CONNECTOR A (44P)
ACC (RED)JUMPER WIRE
ECM/PCM CONNECTOR B (44P)ALTF
(WHT/RED)
13. Momentarily connect ECM/PCM connector terminalA14 to body ground with a jumper wire s everal
times.
Update the ECM/PCM if it does not have the
latest software (see page 11-227), or substitute a
known-good ECM/PCM (see page 11-7), then
recheck. If the symptom/indication goes away with
a known-good ECM/PCM, replace the original ECM/
PCM (see page 11-228).
Check for poor connections or loose terminals
attheA/CclutchrelayandtheECM/PCM.Ifthe
connections and the terminals are OK, check the
A/C compressor clutch relay (see page 22-70),
repair open in the wires between the ECM/PCM
(A14), the A/C compressor clutch relay, and other
A/C systems parts. 1. Start the engine, and let it idle.
2. Monitor the ALTERNATOR in the DATA LIST with
the HDS.
3. Check if the indicated percentage varies when the headlight switch is turned on.
The alternator signal circuit is OK.
Go to step 4.
4. Turn the headlight switch and ignition switch to LOCK (0).
5. Jump the SCS line with the HDS.
6. Disconnect the alternator 4P connector.
7. Disconnect ECM/PCM connector B (44P).
8. Check for continuity between body ground and ECM/PCM connector terminal B43.
Repair short in the wire between the ECM/
PCM (B43) and the alternator.
Update the ECM/PCM if it does not have the
latest software (see page 11-227), or substitute a
known-good ECM/PCM (see page 11-7), then
recheck. If the symptom/indication goes away with
a known-good ECM/PCM, replace the original ECM/
PCM (see page 11-228).
Terminal side of female terminals
Terminal side of female terminals
I s t her e a cl i ck i ng noi se f r om t he A/ C compr essorclutch? Does t he per cent age v ar y ?
Is there continuity?
08/08/21 14:29:37 61SNR030_110_0307
ProCarManuals.com
DYNOMITE -2009-
(#'
)
¶
¶
¶
¶
¶
¶
Idle speed should be:
K20Z2 engine:
M/T 700 50 rpm
A/T 800 50 rpm (in P or N)
K20Z3 engine: M/T 750 50 rpm
Idle speed should be:
K20Z2 engine: M/T 780 50 rpm
A/T 800 50 rpm (in P or N)
K20Z3 engine: M/T 750 50 rpm
Procedure
11-31011-310Idle Control System
Idle Speed Inspection (cont’d) ECM/PCM Idle Learn Procedure
4. Start the engine. Hold the engine speed at
3,000 rpm without load (A/T in P or N, M/T in
neutral) until the radiator fan comes on, then let it
idle.
5. Check the idle speed without load conditions: headlights, blower fan, radiator fan, and air
conditioner off.
6. Let the engine idle for 1 minute with high electric load (A/C switch on, temperature set to max cool,
blower fan on high, and headlights on high beam).
NOTE: If the idle speed is not within specification,
dotheECM/PCMidlelearnprocedure(seepage
11-310). If the idle speed is still not within
specification, go to the symptom troubleshooting.
7. Reconnect the EVAP canister purge valve connector. The idle learn procedure must be done so the ECM/PCM
can learn the engine idle characteristics.
Do the idle learn procedure whenever you do any of
these actions:
Replace the ECM/PCM.
Reset the ECM/PCM.
Update the ECM/PCM.
Replace or clean the throttle body.
Disassemble the engine or the transmission.
NOTE: Erasing DTCs with the HDS does not require you
to do the idle learn procedure.
1. Make sure all electrical items (A/C, audio, lights, etc.) are off.
2. Reset the ECM/PCM with the HDS.
3. Turn the ignition switch to ON (II), and wait 2 seconds.
4. Start the engine. Hold the engine speed at 3,000 rpm without load (A/T in P or N, M/T in
neutral) until the radiator fan comes on, or until the
engine coolant temperature reaches 90 °C (194 °F).
5. Let the engine idle for about 5 minutes with the throttle fully closed.
NOTE: If the radiator fan comes on, do not include
its running time in the 5 minutes.
08/08/21 14:29:38 61SNR030_110_0310
ProCarManuals.com
DYNOMITE -2009-
(#'
)
¶
¶
¶
¶
¶
¶
Idle speed should be:
K20Z2 engine:
M/T 700 50 rpm
A/T 800 50 rpm (in P or N)
K20Z3 engine: M/T 750 50 rpm
Idle speed should be:
K20Z2 engine: M/T 780 50 rpm
A/T 800 50 rpm (in P or N)
K20Z3 engine: M/T 750 50 rpm
Procedure
11-31011-310Idle Control System
Idle Speed Inspection (cont’d) ECM/PCM Idle Learn Procedure
4. Start the engine. Hold the engine speed at
3,000 rpm without load (A/T in P or N, M/T in
neutral) until the radiator fan comes on, then let it
idle.
5. Check the idle speed without load conditions: headlights, blower fan, radiator fan, and air
conditioner off.
6. Let the engine idle for 1 minute with high electric load (A/C switch on, temperature set to max cool,
blower fan on high, and headlights on high beam).
NOTE: If the idle speed is not within specification,
dotheECM/PCMidlelearnprocedure(seepage
11-310). If the idle speed is still not within
specification, go to the symptom troubleshooting.
7. Reconnect the EVAP canister purge valve connector. The idle learn procedure must be done so the ECM/PCM
can learn the engine idle characteristics.
Do the idle learn procedure whenever you do any of
these actions:
Replace the ECM/PCM.
Reset the ECM/PCM.
Update the ECM/PCM.
Replace or clean the throttle body.
Disassemble the engine or the transmission.
NOTE: Erasing DTCs with the HDS does not require you
to do the idle learn procedure.
1. Make sure all electrical items (A/C, audio, lights, etc.) are off.
2. Reset the ECM/PCM with the HDS.
3. Turn the ignition switch to ON (II), and wait 2 seconds.
4. Start the engine. Hold the engine speed at 3,000 rpm without load (A/T in P or N, M/T in
neutral) until the radiator fan comes on, or until the
engine coolant temperature reaches 90 °C (194 °F).
5. Let the engine idle for about 5 minutes with the throttle fully closed.
NOTE: If the radiator fan comes on, do not include
its running time in the 5 minutes.
08/08/21 14:29:38 61SNR030_110_0310
ProCarManuals.com
DYNOMITE -2009-
Î
(#') µ
µ
YES
NO
11-318 Fuel Supply System
Fuel Pump Circuit Troubleshooting
A
PGM-FI MAIN RELAY 2 (FUEL PUMP) 4P CONNECTOR IGP UNDER-DASH FUSE/RELAY BOX CONNECTOR G (21P)
IGP (ORN)
JUMPER WIRE
UNDER-HOOD FUSE/RELAY BOX CONNECTOR E (10P) IGP (ORN)
If you suspect a problem with the fuel pump, check that
the fuel pump actually runs; when it is on, you will hear
some noise if you listen to the fuel fill port with the fuel
fill cap removed. The fuel pump should run for
2 seconds when the ignition switch is first turned on. If
the fuel pump does not make noise, check as follows:1. Turn the ignition switch to LOCK (0).
2. Remove the under-dash fuse/relay box (see page 22-66), then remove PGM-FI main relay 2 (FUEL
PUMP) (A) from the under-dash fuse/relay box.
3. Reinstall the under-dash fuse/relay box.
4. Turn the ignition switch to ON (II).
5. Measure the voltage between PGM-FI main relay 2 (FUEL PUMP) 4P connector terminal No. 4 and
body ground. Go to step 12.
Go to step 6.
6. Turn the ignition switch to LOCK (0).
7. Disconnect the under-hood fuse/relay box connector E (10P).
8. Disconnect the C101 connector at left side of engine compartment (see page 22-16).
9. Disconnect under-dash fuse/relay box connector G (21P).
10. Connect under-dash fuse/relay box connector G (21P) terminal No. 4 to body ground with a jumper
wire.
11. Check for continuity between under-hood fuse/ relay box connector E (10P) terminal No. 5 and
body ground.
Terminal side of female terminals Wire side of female terminals
Wire side of female terminals
Is there battery voltage?
08/08/21 14:29:45 61SNR030_110_0318
ProCarManuals.com
DYNOMITE -2009-
(#'")
With the HDS
11-322 Fuel Supply System
Fuel Pressure Relieving
A
A
A
Before disconnecting fuel lines or hoses, relieve
pressure from the system by disabling the fuel pump
and then disconnecting the fuel tube/quick connect
fitting in the engine compartment. 1. Turn the ignition switch to LOCK (0).
2. Connect the HDS to the data link connector (DLC) (A) located under the driver’s side of the dashboard.
3. Turn the ignition switch to ON (II).
4. Make sure the HDS communicates with the ECM/ PCM. If it doesn’t, go to the DLC circuit
troubleshooting (see page 11- 204).
5. Turn the ignition switch to LOCK (0).
6. Remove the fuel fill cap to relieve the pressure in the fuel tank.
7. Turn the ignition switch to ON (II).
8. From the INSPECTION MENU of the HDS, select Fuel Pump OFF, then start the engine, and let it idle
until it stalls.
NOTE: Do not allow the engine to idle above 1,000 rpm or the ECM/PCM will continue to operate the fuel
pump.
A DTC or a Temporary DTC may be set during this procedure. Check for DTCs, and clear them
as needed (see page 11-4). 9. Turn the ignition switch to LOCK (0).
10. Do the battery terminal disconnection procedure (see page 22-68).
11. Remove the quick-connect fitting cover (A).
12. Check the fuel quick-connect fitting for dirt, and clean it if needed.
13. Place a rag or shop towel over the quick-connect fitting (A).
08/08/21 14:29:48 61SNR030_110_0322
ProCarManuals.com
DYNOMITE -2009-