(#'
)
20-34 Mirrors
Mirror Holder Replacement
A
B C
A
B
C
D E
C
E
F A
B
C B
A B
C
A
C
CB A
A
B
C
NO GOOD
OK
NOTE: Put on gloves to protect your hands.
1. Carefully push on the top edge of the mirror holder (A) by hand.
2. Put a shop towel in the opening between the lower edge of the mirror holder and the mirror housing
(B) to prevent scratches, and detach the bottom
clips (C) with a flat-tip screwdriver wrapped with
protective tape.
3. Carefully pull out the bottom edge of the mirror holder (A) to separate the adhesive (B), and then
release the side clips (C).
4. Separate the mirror holder from the actuator (D) by releasing the hooks (E). Disconnect the mirror
defogger connectors (F) from the heater pad
terminals. 5. Before reinstalling the mirror holder to the inner
holder (A) on the actuator, check the actuator rods
(B) and the actuator boots (C). Make sure the
actuator rods are securely mounted in the holes,
and that the boots properly cover each rod.
6. Reconnect the mirror defogger connectors.
7. Reattach the hooks of the mirror holder to the actuator, then position the mirror holder on the
actuator. Carefully push on the clip portions of the
mirror holder until the mirror holder locks into
place.
8. Check the actuator operation.
08/08/21 15:00:05 61SNR030_200_0036
ProCarManuals.com
DYNOMITE -2009-
(#'
)
20-35
Rearview Mirror Replacement
A
A B
C
1. Turn the rearview mirror base (A) 90 °.
2. Slide the rearview mirror (A) down toward thebottom of the windshield to detach it from the
spring (B) in the mount (C).
3. Install the rearview mirror in the reverse order of removal.
08/08/21 15:00:05 61SNR030_200_0037
ProCarManuals.com
DYNOMITE -2009-
(#'
) Cutting positions
20-38
Glass
Windshield Replacement
A
B A
B A
B
C
A B
A
A
A
C
A
NOTE:
Put on gloves to protect your hands.
Wear eye protection while cutting the glass adhesive with a piano wire.
Use seat covers to avoid damaging the seat.
When replacing a broken windshield, a commercially available windshield cutter can be efficiently used for
cutting the adhesive. For details, follow the tool
manufacturer’s instructions.
1. Remove these items: Windshield wiper arms (see page 22-233)
Cowl covers (see page 20-163)
Rearview mirror (see page 20-35)
A-pillar trim, both sides (see page 20-69)
Roof moldings (see page 20-165)
2. Remove the molding (A) from the upper edge of the windshield (B). If necessary, cut the molding with a
utility knife.
3. If the old windshield will be reinstalled, make alignment marks across the glass and the body
with a grease pencil.
4. Pull down the front portion of the headliner (see page 20-84). Take care not to bend the
headliner excessively, or you may crease or break
it.
5. Apply protective tape along the edge of the dashboard and the body. Make a hole with an awl
through the rubber dam and adhesive from inside
the vehicle at a corner of the windshield. Push a
piece of piano wire through the hole, and wrap
each end around a piece of wood. 6. With a helper on the outside, pull the piano wire (A)
back and forth in a sawing motion. Hold the piano
wire as close to the windshield (B) as possible to
prevent damage to the body and the dashboard.
Carefully cut through the rubber dam and adhesive
(C) around the entire windshield.
7. Carefully remove the windshield.
08/08/21 15:00:07 61SNR030_200_0040
ProCarManuals.com
DYNOMITE -2009-
Î
(#'
)
S
pecial Tools Required
20-84 Interior Trim
Headliner Removal/Installation
A
B
C A
B
F
astener Locations
:TORXScrew,2
AB
KTC trim tool set SOJATP2014
SRS components are located in this area. Review the
S
RS component locations, (see page 24-11) and the
precautions and procedures (see page 24-13) before
doing repairs or service.
NOTE: Put on gloves to protect your hands.
Take care not to bend or scratch the trim and panels.
Use the appropriate tool from the KTC trim tool set to avoid damage when removing components.
1. Do the battery terminal disconnection procedure (see page 22-68), and wait at least 3 minutes before
beginning work.
2. Remove these items: A-pillar trim, both sides (see page 20-69)
Ceiling light (see page 22-197)
Front seat belt upper anchor, both sides (see step6 on page 24-4)
B-pillar lower trim, both sides (see page 20-72)
B-pillar upper trim, both sides (see page 20-72)
C-pillar trim, both sides (see page 20-75)
Grab handles, four places (see page 20-82)
3. Release the tabs (A) from the bracket (B) of the sunvisor cap (C) with a trim tool. 4
. Remove the sunvisor cap (A) from the bracket (B).
5. From both sides, remove the sunvisor (A). –1 Remove the sunvisor from the body and theholder (B).
–2 Remove the screws with a TORX T25 bit.
–3 Remove the sunvisor from the body, and if equipped disconnect the vanity mirror light
connector.
08/08/21 15:01:39 61SNR030_200_0086
ProCarManuals.com
DYNOMITE -2009-
Î
20-87
Fastener Locations:Bolt,1
A :Bolt,2
B
A
B C
B D
5x0.8mm
6N·m
(0.6 kgf·m, 4 lbf·ft)
5x0.8mm
6N·m
(0.6 kgf·m, 4 lbf·ft)
16. If necessary, remove the side curtain airbag mounting bolt (A) and grab handle bracket
mounting bolts (B), then remove the grab handle
bracket (C) from each side by releasing the hooks
(D). 17. Install the headliner in the reverse order of removal,
and note these items:
If the side curtain airbag has deployed, replace the headliner and related parts with new ones
(see page 24-185).
To prevent the side curtain airbags from deploying improperly and possibly causing
injury, inspect the removed pieces and replace
them if they have any of the following damage:
– Any crease or tears in the headliner (A)
– Any cracks or breakage in the grab handle (B)
– Any damages around the grab handle holes (C) or sunvisor holes in the headliner
– Any cracks in the sunvisor stay base (D)
– Any bends or cracks in the sunvisor stay shaft (E)
– Any cracks in the sunvisor base (F)
– Any cracks or breakage in the vanity mirror base (G)
– Any Velcro fasteners (H) and the clip bases (I) which have come off the headliner
When installing the grab handle, push on the grab handle against the bracket (J) until the clips
(K) snap into place securely.
If the clips are damaged or stress-whitened, replace them with new ones.
Replace the removed cushion tape with new ones.
Check that both sides of the headliner are securely attached to the trim.
Make sure the headliner overlaps the trim pieces correctly (see page 24-187).
When reinstalling the headliner through the front passenger’s door opening, be careful not to fold
or bend it. Also, be careful not to scratch the
body.
Check for any DTCs that may have been set during repairs, and clear them.
Do the battery terminal reconnection procedure (see page 22-68).
(cont’d)
08/08/21 15:01:41 61SNR030_200_0089
ProCarManuals.com
DYNOMITE -2009-
(#'
/)
Body Electrical
Body Electrical..................................
..................................
Relay and Control Unit
Locations . 22-7
................
Connectors and Harnesses . 22-13
........................
........................
Fuse/Relay Boxes . 22-58
......................
......................
Power Distribution . 22-60
....................
....................
Ground Distribution . 22-64
Under-hood Fuse/Relay Box
Under-dash Fuse/Relay Box
Battery
Relays
Ignition Switch
Multiplex Integrated Control System Keyless/Power Door Locks/Security
System
Horns
Exterior Lights
Turn Signal/Hazard Warning Lights
Interior Lights.............................................. .....
..............................................
.....
Special Tools . 22-2
General Troubleshooting Information . 22-3
.......................... ..........................
Removal and Installation . 22-65
..........................
..........................
Removal and Installation . 22-66
.......................................................................................... .............
................................................
.......................................... .............
Battery Test
. 22-67
Battery Terminal Disconnection and Reconnection . 22-68
Battery Removal and Installation . 22-69
.......................................
.......................................
Power Relay Test . 22-70
............................................................. ..............................................
.............................................................
..............................................
Test
. 22-72
Replacement . 22-72
...................... .....
......................
...................................
.........................
..........................
.......................... .........................
............
................
.......................................... ................................
......................................... ......................
.....
......................
...................................
.........................
..........................
.......................... .........................
............
................
.......................................... ................................
.........................................
Component Location Index
. 22-73
General Troubleshooting Information . 22-74
DTC Troubleshooting Index . 22-77
System Description . 22-80
Troubleshooting-B-CAN System Diagnosis Test Mode A . 22-93
Troubleshooting-B-CAN System Diagnosis Test Mode B . 22-94
Troubleshooting-B-CAN System Diagnosis Test Mode C . 22-95
Troubleshooting-B-CAN System Diagnosis Test Mode D . 22-96
Troubleshooting-B-CAN System Diagnosis Test Mode 1 and
Test Mode 2 (Without the HDS) . 22-97
Sleep and Wake-up Mode Test . 22-99
Circuit Diagram . 22-100
DTC Troubleshooting . 22-102
MICU Input Test . 22-109 ......................
...................................
.......................................... ......................................................
.............................
......................................... ................................................
............................... ...............................
....................................... .................
......................
...................................
.......................................... ......................................................
.............................
......................................... ................................................
............................... ...............................
....................................... .................
Component Location Index
. 22-112
System Description . 22-114
Circuit Diagram . 22-116
DTC Troubleshooting . 22-120
Symptom Troubleshooting . 22-126
Tripped Sensor History . 22-130
MICU Input Test . 22-131
Door Lock Actuator Test . 22-137
Door Lock Knob Switch Test . 22-138
Door Lock Switch Test . 22-139
Door Key Cylinder Switch Test . 22-140
Trunk Lid Release Actuator Test . 22-141
Hood Switch Test . 22-141
Transmitter Test/Replacement . 22-142
......................
.......................................... ............................
....................................... ......................
.......................................... ............................
.......................................
Component Location Index
. 22-145
Circuit Diagram . 22-146
Horn Test/Replacement . 22-146
Horn Switch Test . 22-147
......................
.......................................... ................................
.........................................
........................................... ..............................
............................... ........
............................... .............................
.............................
................................
..................................... ............................... ........................................
.............
......................
.......................................... ................................
.........................................
........................................... ..............................
............................... ........
............................... .............................
.............................
................................
..................................... ............................... ........................................
.............
Component Location Index
. 22-148
Circuit Diagram . 22-150
DTC Troubleshooting . 22-157
MICU Input Test . 22-163
Combination Light Switch Test/ Replacement . 22-166
HID Bulb Replacement . 22-168
HID Unit Replacement . 22-169
HID Lamp System Troubleshooting . 22-170
Headlight Adjustment . 22-173
Headlight Replacement . 22-174
Fog Light Replacement . 22-175
Fog Light Adjustment . 22-176
Bulb Replacement . 22-177
Taillight Replacement . 22-179
Inner Taillight Replacement . 22-179
License Plate Light Replacement . 22-180
High Mount Brake Light Replacement . 22-180
Brake Pedal Position Switch Test . 22-181
......................
.......................................... ................................
.........................................
.................................. .......
......................
.......................................... ................................
.........................................
.................................. .......
Component Location Index
. 22-182
Circuit Diagram . 22-184
DTC Troubleshooting . 22-186
MICU Input Test . 22-188
Hazard Warning Switch Test/Replacement . 22-192
Side Turn Signal Light Replacement . 22-192
......................
..........................................
........................................... ...............
.......................... ............
.................... ................
...................... .............
......................
..........................................
........................................... ...............
.......................... ............
.................... ................
...................... .............
Component Location Index
. 22-193
Circuit Diagram . 22-194
Front Individual Map Light Test/ Replacement . 22-196
Ceiling Light Test/Replacement . 22-197
Trunk Light Replacement . 22-197
Ambient Light Test/Replacement . 22-198
Courtesy Light Replacement . 22-198
Glove Box Light Test/Replacement . 22-199
Vanity Mirror Light Test/Replacement . 22-199
Interior Light Switch Test/Replacement . 22-200
Trunk Lid Latch Switch Test . 22-200
Footwell Light Test/Replacement . 22-201
08/08/21 14:22:03 61SNR030_220_0002
ProCarManuals.com
DYNOMITE -2009-
Entry Lights Control System
Power Windows
Wipers/Washers
GaugesReminder Systems
Moonroof
Accessory Power Sockets
Seat Heaters
Power Mirrors
Rear Window Defogger
Immobilizer System......................
.......................................... ......................................... ...........................
.............................. ......................
.......................................... ......................................... ...........................
..............................
Component Location Index . 22-202
Circuit Diagram . 22-203
MICU Input Test . 22-204
Ignition Key Switch Test . 22-207
Ignition Key Light Test . 22-207
......................
...................................
............................................ ..........................................
.......................................................... ........
.......................................................... ..................................
........................................................
...................................
............................................ ..........................................
.......................................................... ........
.......................................................... ..................................
..................................
Component Location Index
. 22-208
System Description . 22-209
Resetting the Power Window Control Unit . 22-210
Circuit Diagram . 22-212
Power Window Master Switch Input Test . 22-214
Driver’s Power Window Motor Test . 22-217
Passenger’s Power Window Motor Test . 22-218
Power Window Master Switch Test/Replacement . 22-219
Passenger’s Power Window Switch Test/Replacement . 22-220
......................
.......................................... ................................
......................................... .......................
....................................... .................................... ...............
....................... ........
...............
........................ ................
...................... ......................
.......................................... ................................
......................................... .......................
....................................... .................................... ...............
....................... ........
...............
........................ ................
......................
Component Location Index
. 22-221
Circuit Diagram . 22-223
DTC Troubleshooting . 22-224
MICU Input Test . 22-228
Wiper/Washer Switch Test . 22-231
Wiper Motor Test . 22-231
Washer Motor Test . 22-232
Washer Fluid Level Switch Test . 22-232
Wiper Motor Replacement . 22-233
Wiper/Washer Switch Replacement . 22-234
Washer Reservoir Replacement . 22-234
Wiper Blade Replacement . 22-235
Wiper Arm/Nozzle Adjustment . 22-236
Washer Tube Replacement . 22-237
......................
...........................
.......................................... ................................
................................................
................................................
......................................
..............................................
..................................
.............................................. ......................
...........................
.......................................... ................................
................................................
................................................
......................................
..............................................
..................................
..............................................
Component Location Index
. 22-238
Self-diagnostic Function . 22-241
Circuit Diagram . 22-244
DTC Troubleshooting . 22-262
Gauge Control Module (Tach) Input Test . 22-271
Gauge Control Module (Speedo) Input Test . 22-274
Rewriting the ODO Data and Transferring the Maintenance
Minder Data to a New Gauge
Control Module . 22-276
Replacement . 22-277
Dash Lights Brightness Controller and Odometer Select/Reset Switch
Test/Replacement . 22-278
Outside Air Temperature Indicator Calibration . 22-279 ......................
.......................................... ......................................... ......................
.......................................... .........................................
Component Location Index
. 22-281
Circuit Diagram . 22-282
MICU Input Test . 22-284
...................... ......
.......................................... ...................
......................
......
.......................................... ...................
Component Location Index
. 22-286
Resetting the Moonroof Control Unit . 22-287
Circuit Diagram . 22-288
Moonroof Control Unit Input Test . 22-290
Moonroof Switch Test/Replacement . 22-293
......................
..........................................
..................................
.................................. ......................
..........................................
..................................
..................................
Component Location Index
. 22-294
Circuit Diagram . 22-295
Front Accessory Power Socket Test/Replacement . 22-296
Console Accessory Power Socket Test/Replacement . 22-297
......................
.......................................... .........................
........................................ ......................
.......................................... .........................
........................................
Component Location Index
. 22-298
Circuit Diagram . 22-300
Switch Test/Replacement . 22-302
Seat Heater Test . 22-302
......................
..........................................
..............................................
........................................................ .......
......................
..........................................
..............................................
........................................................ .......
Component Location Index
. 22-304
Circuit Diagram . 22-305
Function Test . 22-306
Power Mirror Switch Test/Replacement . 22-307
Power Mirror Actuator Test . 22-307
Power Mirror Actuator Replacement . 22-308
......................
..........................................
.............................................. ......................................................
..........................................
.............................................. ................................
Component Location Index
. 22-310
Circuit Diagram . 22-311
Function Test . 22-312
Defogger Wire Repair . 22-313
......................
...................................
.......................................... ................................
............................................. ......................
............................................
.................................................. ...................
................................................ ........................................... ......................
...................................
.......................................... ................................
............................................. ......................
............................................
.................................................. ...................
................................................ ...........................................
Component Location Index
. 22-314
System Description . 22-315
Circuit Diagram . 22-316
DTC Troubleshooting . 22-317
Symptom Troubleshooting Information . 22-321
Symptom Troubleshooting . 22-323
System Check . 22-326
Status Log . 22-328
Immobilizer Key Registration . 22-329
Immobilizer-Keyless Control Unit Input Test . 22-330
Immobilizer-Keyless Control Unit Replacement . 22-332
08/08/21 14:22:03 61SNR030_220_0003
ProCarManuals.com
DYNOMITE -2009-
Î
(#')
22-7
Relay and Control Unit Locations
Engine Compartment
ABS MODULATOR-CONTROL UNIT
(’06-07 Touring and Premium models) or
VSA MODULATOR-CONTROL UNIT
(’07 TYPE S and ’08-09 models)
ECM/PCM
A/C CONDENSER FAN RELAY FAN CONTROL RELAY
BLOWER MOTOR RELAYPOWERMIRRORDEFOGGERRELAY
PGM-FI SUBRELAY
REAR WINDOW DEFOGGER RELAY
IGNITION COIL RELAY
A/C COMPRESSOR CLUTCH RELAY
UNDER-HOOD FUSE/RELAY BOX
PGM-FI MAIN RELAY 1
(FI MAIN) RADIATOR FAN RELAY
ELECTRONIC THROTTLE CONTROL
SYSTEM (ETCS) CONTROL RELAY
ELECTRICAL LOAD DETECTOR (ELD)
08/08/21 14:22:06 61SNR030_220_0009
ProCarManuals.com
DYNOMITE -2009-