2006 ACURA CSX fuel
[x] Cancel search: fuelPage 421 of 2893
µµ
(#'
)
µ
µ
µ
µ µ
µ
µ
µ
YES
NO
YES
NO
YES
NO
YES
NO
DTC P0134:
11-9811-98PGM-FI System
DTC Troubleshooting (cont’d)
10. Do the ECM/PCM idle learn procedure (see page
11-310).
11. Start the engine. Hold the engine speed at 3,000 rpm without load (A/T in P or N, M/T in
neutral) until the radiator fan comes on, then let it
idle.
12. Test-drive under these conditions:
Engine coolant temperature (ECT SENSOR 1)above70°C(158°F)
A/TinD,M/Tin3rdor4th
Drive the vehicle at 40 km/h (25 mph) or less for 5 minutes, then drive at a steady speed between
41 130 km/h (26 81 mph).
13. Check for Temporary DTCs or DTCs with the HDS.
Check for poor connections or loose
terminals at the A/F sensor (Sensor 1) and the ECM/
PCM, then go to step 1.
Go to step 14.
14. Monitor the OBD STATUS for DTC P0133 in the DTCs MENU with the HDS.
Troubleshooting is complete. If any other
Temporary DTCs or DTCs were indicated in step 13,
go to the indicated DTC’s troubleshooting.
If the screen indicates FAILED, check for poor
connections or loose terminals at the A/F sensor
(Sensor1)andtheECM/PCM,thengotostep1.If
the screen indicates EXECUTING, keep driving until
a result comes on. If the screen indicates OUT OF
CONDITION, go to step 11. NOTE:
Before you troubleshoot, record all freeze data and any on-board snapshot, and review the general
troubleshooting information (see page 11-3).
If the vehicle was out of fuel and the engine stalled before this DTC was stored, refuel and clear the DTC
with the HDS.
If DTC P0135 is stored at the same time as DTC P0134, troubleshoot DTC P0135 first, then recheck for DTC
P0134.
1. Turn the ignition switch to ON (II).
2. Clear the DTC with the HDS.
3. Start the engine, and let it idle without load (A/T in P or N, M/T in neutral) until the radiator fan comes
on.
4. Check for Temporary DTCs or DTCs with the HDS.
Go to step 5.
Intermittent failure, the system is OK at this
time. Check for poor connections or loose terminals
at the A/F sensor (Sensor 1), the PGM-FI subrelay,
and the ECM/PCM.
5. Turn the ignition switch to LOCK (0).
6. Replace the A/F sensor (Sensor 1) (see page 11-221).
7. Turn the ignition switch to ON (II).
8. Reset the ECM/PCM with the HDS.
9. Do the ECM/PCM idle learn procedure (see page 11-310).
10. Check for Temporary DTCs or DTCs with the HDS.
Check for poor connections or loose
terminals at the A/F sensor (Sensor 1), the PGM-FI
subrelay, and the ECM/PCM, then go to step 1.
Go to step 11.A/F Sensor (Sensor 1) Heater
System Malfunction
Is DT C P0133 ind icated ?
Does t he scr een i nd i cat e PASSE D? Is DT C P0134 ind icated ?
Is DT C P0134 ind icated ?
08/08/21 14:17:18 61SNR030_110_0098
ProCarManuals.com
DYNOMITE -2009-
Page 436 of 2893
(#'
)
µ
µ µ
µ µ
µ
YES
NO
YES
NO
YES
NO
DTC P0171:
DTC P0172:
11-11311-113
29. Reconnect all connectors.
30. Update the ECM/PCM if it does not have the latest
software (see page 11-227), or substitute a known-
good ECM/PCM (see page 11-7).
31. Start the engine, and let idle.
32. Check for Temporary DTCs or DTCs with the HDS.
Check for poor connections or loose
terminals at the secondary HO2S (Sensor 2) and
the ECM/PCM. If the ECM/PCM was updated,
substitute a known-good ECM/PCM (see page 11-7),
then go to step 31. If the ECM/PCM was substituted,
go to step 1.
Go to step 33.
33. Monitor the OBD STATUS for DTC P0141 in the DTCs MENU with the HDS.
If the ECM/PCM was updated,
troubleshooting is complete. If the ECM/PCM was
substituted, replace the original ECM/PCM
(see page 11-228). If any other Temporary DTCs or
DTCs were indicated in step 32, go to the indicated
DTC’s troubleshooting.
If the screen indicates FAILED, check for poor
connections or loose terminals at the secondary
HO2S (Sensor 2) and the ECM/PCM. If the ECM/
PCM was updated, substitute a known-good ECM/
PCM (see page 11-7), then go to step 31. If the ECM/
PCM was substituted, go to step 1. If the screen
indicates NOT COMPLETED, keep idling until a
result comes on. NOTE:
Before you troubleshoot, record all freeze data and any on-board snapshot, and review the general
troubleshooting information (see page 11-3).
If any of the DTCs listed below are indicated at the same time as DTC P0171 and/or P0172, troubleshoot
those DTCs first, then recheck for P0171 and/or P0172.
P0101, P0102, P0103: Mass air flow (MAF) sensor
P0107, P0108, P1128, P1129: Manifold absolute
pressure (MAP) sensor
P0133, P1157, P1172, P2195, P2238, P2252, P2A00: Air
fuel ratio (A/F) sensor (Sensor 1)
P0134, P0135: Air fuel ratio (A/F) sensor (Sensor 1)
heater
P0137, P0138, P0139, P2270, P2271: Sec ondary HO2S
(Sensor 2)
P0141: Secondary HO2S (Sensor 2) heater
P0401 , P0404 , P0406 , P2413 : Exhaust gas
recirculation (EGR) system
P0443, P0496: EVAP canister purge valve
P2646, P2647, P2648, P2649: VTEC system : K20Z2 engine
1. Check the fuel pressure (see page 11-325).
Go to step 2.
If the pressure is too high, replace the fuel pressure regulator (see page 11-337), then go to
step 7.
If the pressure is too low, check the fuel pump, the fuel feed pipe and the fuel filter. If they are
OK, replace the fuel pressure regulator (see page
11-337), then go to step 7.
(cont’d)Fuel System Too Lean
Fuel System Too Rich
Is DTC P0141 indicated?Does t he scr een i nd i cat e PASSE D? Is the fuel pressure OK?
08/08/21 14:17:24 61SNR030_110_0113
ProCarManuals.com
DYNOMITE -2009-
Page 437 of 2893
µµµ
µ
µ
µ
µ
µ
µ µ
µ
µ
µ
YES
NO
YES
NO YES
NO
YES
NO
11-114
PGM-FI System
DTC Troubleshooting (cont’d)
2. Check for vacuum leaks at these parts:
PCV valve
PCV hose
EVAP canister purge valve
Throttle body
Intake manifold
Brake booster
Brake booster hose
Intake air duct
Go to step 3.
Repair or replace the part(s) with leaks, then
go to step 7.
3. Start the engine. Hold the engine speed at 3,000 rpm without load (A/T in P or N, M/T in
neutral) until the radiator fan comes on, then let it
idle.
4. Check for these conditions: Engine coolant temperature (ECT SENSOR 1)above70°C(158°F)
A/T in N, M/T in neutral
All electrical loads off
5. Monitor the ENGINE SPEED in the DATA LIST with the HDS, and hold the engine speed at 2,500 rpm.
Once the engine speed is met, hold the accelerator
pedal steady for more than 10 seconds.
Repeat step 5.
Go to step 6. 6. While holding the engine speed at 2,500 rpm, check
the MAF SENSOR in the DATA LIST with the HDS.
Check the engine valve clearances and adjust
them if needed; K20Z2 engine (see page 6-12),
K20Z3 engine (see page 6-14). If the valve
clearances are OK, replace the injectors (see page
11-219), then go to step 7.
Replace the MAF sensor/IAT sensor (see page
11-224), then go to step 7.
7. Turn the ignition switch to ON (II).
8. Reset the ECM/PCM with the HDS.
9. Do the ECM/PCM idle learn procedure (see page 11-310).
10. Start the engine. Hold the engine speed at 3,000 rpm without load (A/T in P or N, M/T in
neutral) until the radiator fan comes on, then let it
idle.
11. Test-drive under these conditions: Engine coolant temperature (ECT SENSOR 1)above70°C(158°F)
A/TinD,M/Tin4th
Drive at a steady speed between 24 120 km/h (15 75 mph) for 15 minutes
NOTE: DTC P0171 and/or P0172 may take up to
80 minutes of test driving to set. Using the HDS,
monitor or the air fuel feed back average (AF FB
AVE). If the AF FB AVE stays within 0.80 1.25,
there is no problem at this time.
12. Check for Temporary DTCs or DTCs with the HDS.
Go to step 1.
Troubleshooting is complete. If any other
Temporary DTCs or DTCs are indicated, go to the
indicated DTC’s troubleshooting.
Ar e t he par t s OK ?
Di d t he engi ne speed v ar y mor e t han 100 r pm f r om2,500 rpm? Is t her e about 6.0 8.6 ( K 20Z 2 engi ne) or 5.7
8.3(K20Z3engine)gm/s?
I s DT C P017 1 or P017 2 i nd i cat ed ?
08/08/21 14:17:24 61SNR030_110_0114
ProCarManuals.com
DYNOMITE -2009-
Page 438 of 2893
(#'
) µ
µ
µ
µ
µ
µ
DTC P0300:
DTC P0301:
DTC P0302:
DTC P0303:
DTC P0304:
Special Tools Required YES
NO
YES
NO
YES
NO
11-115
Random Misfire and Any
Combination of the Following:
No. 1 Cylinder Misfire Detected
No. 2 Cylinder Misfire Detected
No. 3 Cylinder Misfire Detected
No. 4 Cylinder Misfire Detected
Pressure gauge adapter 07NAJ-P07010A
A/T low pressure gauge w/panel 07406-0070301
A/T pressure hose 07406-0020201
A/T pressure hose, 2,210 mm 07MAJ-PY4011A
A/T pressure hose, adapter 07MAJ-PY40120
Oil pressure hose 07ZAJ-S5AA200
NOTE: Before you troubleshoot, record all freeze data and any on-board snapshot, and review the general
troubleshooting information (see page 11-3).
If the misfire is frequent enough to trigger detection of increased emissions during two consecutive
driving cycles, the MIL will come on, and DTC P0300
(and some of the combination of P0301 thr ough
P0304) will be stored.
If the misfire is frequent enough to damage the catalyst, the MIL will blink whenever the misfire
occurs, and DTC P0300 (and some of the combination
of P0301 through P0304) will be stored. When the
misfire stops, the MIL will remain on.
If any of the DTCs listed below are indicated at the same time as the random misfire DTCs, troubleshoot
those DTCs first, then recheck for random misfire
DTCs:
P0101, P0102, P0103: Mass air flow (MAF) sensor
P0107, P0108: Manifold absolute pressure (MAP)
sensor
P0171, P0172: Fuel system
P0335, P0339: Crankshaft position (CKP) sensor
P0365, P0369: Camshaft position (CMP) sensor B
P0401 , P0404 , P0416 , P2413 : Exhaust gas
recirculation (EGR) system
P0506, P0507: Idle control system
P2646, P2647, P2648, P2649: VTEC system : K20Z2 engine 1. Turn the ignition switch to ON (II).
2. Clear the DTC with the HDS.
3. Start the engine, and let it idle without load (A/T in
P or N, M/T in neutral).
4. Monitor the OBD STATUS for DTC P0301, P0302, P0303, or P0304 in the DTCs MENU with the HDS.
Go to step 9.
If the screen indicates PASSED, go to step 5. If
the screen indicates EXECUTING, keep idling until
a result comes on. If the screen indicates OUT OF
CONDITION, wait for several minutes, then recheck.
5. Check the CYL1 MISFIRE, CYL2 MISFIRE, CYL3 MISFIRE, and/or CYL4 MISFIRE in the DATA LIST
for 10 minutes with the HDS.
Go to step 9.
Go to step 6.
6. Test-drive the vehicle for several minutes in the range of these recorded freeze data parameters:
ENGINE S PEED
VSS
REL TP SENSOR
CLV (calculated load value)
APP SENSOR
7. Monitor the OBD STATUS for DTC P0301, P0302, P0303, or P0304 in the DTCs MENU with the HDS.
Go to step 9.
If the screen indicates PASSED, go to step 8. If
the screen indicates EXECUTING, keep driving until
a result comes on. if the screen indicates OUT OF
CONDITION, go to step 6 and recheck.
(cont’d)
Does t he scr een i nd i cat e F AILE D?
Does the CYL1 MISFIRE, CYL2 MISFIRE, CYL3M I SF I RE , and / or CY L4 M I SF I RE show mi sf i r ecounts?
Does t he scr een i nd i cat e F AILE D?
08/08/21 14:17:24 61SNR030_110_0115
ProCarManuals.com
DYNOMITE -2009-
Page 439 of 2893
µ
µ
µ
µ
µ
µ
µ
µ µ
µ
µ
µ
µ
µ
YES
NO
YES
NO
YES
NO YES
NO
YES
NO
YES
NO
11-116
PGM-FI System
DTC Troubleshooting (cont’d)
8. Check the CYL1 MISFIRE, CYL2 MISFIRE, CYL3
MISFIRE, and/or CYL4 MISFIRE in the DATA LIST
for 10 minutes with the HDS.
Go to step 9.
Intermittent failure, the system is OK at this
time.
9. Turn the ignition switch to LOCK (0).
10. Check the fuel quality.
Go to step 11.
Drain the tank, fill it with a known-good fuel,
then go to step 25.
11. Inspect the spark plugs (see page 4-21). If the spark plugs are fouled or worn, replace them.
12. Test-drive the vehicle for several minutes in the range of these recorded freeze data parameters:
ENGINE S PEED
VSS
REL TP SENSOR
CLV (calculated load value)
APP SENSOR
13. Check the CYL1 MISFIRE, CYL2 MISFIRE, CYL3 MISFIRE, and/or CYL4 MISFIRE in the DATA LIST
for 10 minutes with the HDS.
Go to step 14.
Go to step 25. 14. Check the fuel pressure (see page 11-325).
Go to step 15.
If the fuel pressure is too high, replace the fuel pressure regulator (see page 11-337), then go to
step 25.
If the fuel pressure is too low, check the fuel pump, the fuel feed pipe, and the fuel filter. If
they are OK, replace the fuel pressure regulator
(see page 11-337), then go to step 25.
15. Start the engine. Hold the engine speed at 3,000 rpm without load (A/T in P or N, M/T in
neutral) until the radiator fan comes on, then let it
idle.
16. Check for these conditions: Engine coolant temperature (ECT SENSOR 1)above80°C(176°F)
A/T in P or N, M/T in neutral
All electrical loads off
17. Monitor the ENGINE SPDEED in the DATA LIST with the HDS, and hold the engine speed at
2,500 rpm. Once the engine speed is met, hold the
accelerator pedal steady for more than 10 seconds.
Repeat step 17.
Go to step 18.
18. While holding the engine speed at 2,500 rpm, check the MAF SENSOR in the DATA LIST with the HDS.
Go to step 19.
Replace the MAF sensor/IAT sensor (see page
11-224), then go to step 25.
Does the CYL1 MISFIRE, CYL2 MISFIRE, CYL3 M I SF I RE , and / or CY L4 M I SF I RE show mi sf i r ecounts?
Is the quality good?
Does the CYL1 MISFIRE, CYL2 MISFIRE, CYL3M I SF I RE , and / or CY L4 M I SF I RE show mi sf i r ecounts? Is the fuel pressure OK?
Di d t he engi ne speed v ar y mor e t han 100 r pm f r om2,500 rpm?
Is t her e about 6.0 8.6 ( K 20Z 2 engi ne) or5.7 8.3 (K 20Z 3 engine) gm/ s?
08/08/21 14:17:24 61SNR030_110_0116
ProCarManuals.com
DYNOMITE -2009-
Page 440 of 2893
µ
µ µ
µ
µ
µ
YES
NO YES
NO
YES
NO
11-117
07406-0020201 or
07MAJ-PY4011A and
07MAJ-PY40120
A
22 N·m
(2.2 kgf·m,
16 lbf·ft)
07406-0070301
B
07NAJ-P07010A
07ZAJ-S5AA200
19. Turn the ignition switch to LOCK (0).
20. Remove the cowl cover and the under cowl panel (see page 20-163).
21. Remove the rocker arm oil pressure switch (A), and attach the special tools as shown, then attach the
rocker arm oil pressure switch to the pressure
gauge attachment (B).
NOTE: Install the parts in the reverse order of
removal with a new O-ring.
22. Reconnect the rocker arm oil pressure switch 2P connector.
23. Start the engine. Hold the engine speed at 3,000 rpm without load (A/T in P or N, M/T in
neutral) until the radiator fan comes on, then let it
idle.
24. Check the oil pressure at engine speeds of 1,000 rpm and 2,000 rpm.
Check for air in the fuel line, then go to step
25.
Inspect the VTEC system, then go to step 25. 25. Turn the ignition switch to ON (II).
26. Reset the ECM/PCM with the HDS.
27. Clear the CKP pattern with the HDS.
28. Do the ECM/PCM idle learn procedure (see page
11-310).
29. Do the CKP pattern learn procedure (see page 11-4).
30. Test-drive the vehicle for several minutes in the range of these recorded freeze data parameters:
ENGINE S PEED
VSS
REL TP SENSOR
CLV (calculated load value)
APP SENSOR
31. Check for Temporary DTCs or DTCs with the HDS.
Check for poor connections or loose
terminals at the ignition coil(s), the injector(s), and
the ECM/PCM, then go to troubleshooting DTC
P0301, P0302, P0303, or P0304 (see page 11-118).
Go to step 32.
32. Monitor the OBD STATUS for DTC P0301, P0302, P0303, or P0304 in the DTCs MENU with the HDS.
Troubleshooting is complete. If any other
Temporary DTCs or DTCs were indicated in step 31,
go to the indicated DTC’s troubleshooting.
If the screen indicates FAILED, go to step 1
and recheck. If the screen indicates EXECUTING,
keep driving until a result comes on. If the screen
indicates OUT OF CONDITION, go to step 30.
Is t he oi l pr essur e bel ow 49 k Pa ( 0.5 k gf / cm , 7psi)? Is DT C P0300, P0301, P0302, P0303, or P0304
indicated?
Does t he scr een i nd i cat e PASSE D?2
08/08/21 14:17:25 61SNR030_110_0117
ProCarManuals.com
DYNOMITE -2009-
Page 441 of 2893
(#'
)
µ
µ
µ
µ µ
µ
µ
µ
µ
µ
DTC P0301:
DTC P0302:
DTC P0303:
DTC P0304:
YES
NO
YES
NO YES
NO
YES
NO
YES
NO
11-118
PGM-FI System
DTC Troubleshooting (cont’d)
No. 1 Cylinder Misfire Detected
No. 2 Cylinder Misfire Detected
No. 3 Cylinder Misfire Detected
No. 4 Cylinder Misfire Detected
NOTE: Before you troubleshoot, record all freeze data
and any on-board snapshot, and review the general
troubleshooting information (see page 11-3).
1. Turn the ignition switch to ON (II).
2. Clear the DTC with the HDS.
3. Start the engine, and let it idle without load (A/T in P or N, M/T in neutral).
4. Monitor the OBD STATUS for DTC P0301, P0302, P0303, or P0304 in the DTCs MENU with the HDS.
Go to step 9.
If the screen indicates PASSED, go to step 5. If
the screen indicates EXECUTING, keep idling until
a result comes on. If the screen indicates OUT OF
CONDITION, wait for several minutes, and recheck.
5. Check the CYL1 MISFIRE, CYL2 MISFIRE, CYL3 MISFIRE, and/or CYL4 MISFIRE in the DATA LIST
for 10 minutes with the HDS.
Go to step 9.
Go to step 6.
6. Test-drive the vehicle for several minutes in the range of these recorded freeze data parameters:
ENGINE S PEED
VSS
REL TP SENSOR
CLV (calculated load value)
APP SENSOR 7. Monitor the OBD STATUS for DTC P0301, P0302,
P0303, or P0304 in the DTCs MENU with the HDS.
Go to step 9.
If the screen indicates PASSED, go to step 8. If
the screen indicates EXECUTING, keep driving until
a result comes on. If he screen indicates OUT OF
CONDITION, go to step 6 and recheck.
8. Check the CYL1 MISFIRE, CYL2 MISFIRE, CYL3 MISFIRE, and/or CYL4 MISFIRE in the DATA LIST
for 10 minutes with the HDS.
Go to step 9.
Intermittent failure, the system is OK at this
time. Check for the fuel and ignition system circuit
connectors for poor connections or loose
terminals.
9. Turn the ignition switch to LOCK (0).
10. Remove the engine cover; K20Z2 engine (see step 1 on page 9-3), K20Z3 engine (see step 1 on page 9-7).
11. Start the engine, and listen for a clicking sound at the injector of the problem cylinder.
Go to step 12.
Go to step 42.
Does t he scr een i nd i cat e F AILE D?
Does the CYL1 MISFIRE, CYL2 MISFIRE, CYL3M I SF I RE , and / or CY L4 M I SF I RE show mi sf i r ecounts? Does t he scr een i nd i cat e F AILE D?
Does the CYL1 MISFIRE, CYL2 MISFIRE, CYL3M I SF I RE , and / or CY L4 M I SF I RE show mi sf i r ecounts?
Does t he i nj ect or cl i ck ?
08/08/21 14:17:25 61SNR030_110_0118
ProCarManuals.com
DYNOMITE -2009-
Page 497 of 2893
(#'
)
µ
µ
µ
µ µ
µ
µ
µ
YES
NO
YES
NO YES
NO
YES
NO
DTC P2195:
11-17411-174PGM-FI System
DTC Troubleshooting (cont’d)
20. Turn the ignition switch to LOCK (0).
21. Replace ECT sensor 2 (see page 11-225).
22. Reconnect all connectors.
23. Turn the ignition switch to ON (II).
24. Reset the ECM/PCM with the HDS.
25. Do the ECM/PCM idle learn procedure (see page
11-310).
26. Check for Temporary DTCs or DTCs with the HDS.
Check for poor connections or loose
terminals at ECT sensor 2 and the ECM/PCM, then
go to step 1.
Troubleshooting is complete. If any other
Temporary DTCs or DTCs are indicated, go to the
indicated DTC’s troubleshooting.
27. Reconnect all connectors.
28. Update the ECM/PCM if it does not have the latest software (see page 11-227), or substitute a known-
good ECM/PCM (see page 11-7).
29. Check for Temporary DTCs or DTCs with the HDS.
Check for poor connections or loose
terminals at ECT sensor 2 and the ECM/PCM. If the
ECM/PCM was updated, substitute a known-good
ECM/PCM (see page 11-7), then recheck. If the
ECM/PCM was substituted, go to step 1.
If the ECM/PCM was updated, troubleshooting
is complete. If the ECM/PCM was substituted,
replace the original ECM/PCM (see page 11-228). If
any other Temporary DTCs or DTCs are indicated,
go to the indicated DTC’s troubleshooting. NOTE:
Before you troubleshoot, record all freeze data and any on-board snapshot, and review the general
troubleshooting information (see page 11-3).
If the vehicle was out of fuel and the engine stalled before this DTC was stored, refuel and clear the DTC
with the HDS.
If DTC P2101, P2118, P2135, P2138, P2176, or a combination of P2122 and P2127, P2122, and P2138,
or P2127 and P2138 are stored at the same time,
troubleshoot them first, then recheck for DTC P2195.
1. Check the installation of the A/F sensor (Sensor 1).
Go to step 6.
Go to step 2.
2. Turn the ignition switch to ON (II).
3. Clear the DTC with the HDS.
4. Start the engine, and let it idle for 2 minutes.
5. Check for Temporary DTCs or DTCs with the HDS.
Check for poor connections or loose
terminals at the A/F sensor (Sensor 1) and the ECM/
PCM, then go to step 13.
Intermittent failure, the system is OK at this
time. Check for poor connections or loose terminals
at the A/F sensor (Sensor 1) and the ECM/PCM. If
any other Temporary DTCs or DTCs are indicated,
go to the indicated DTC’s troubleshooting.A/F Sensor (Sensor 1) Signal
Stuck Lean
Is DTC P2185 indicated?
Is DTC P2185 indicated? I s t he A/ F sensor l oose or d i sconnect ed f r om t he
ex haust pi pe?
Is DTC P2195 indicated?
08/08/21 14:20:27 61SNR030_110_0174
ProCarManuals.com
DYNOMITE -2009-