2006 ACURA CSX display

µ
´µ
´ ´
Î
Navigation Unit Inputs and Outputs for Connector A (17P)
Navigation Unit Connector A (17P) TerminalNumber Wire Color Terminal Name Description Voltage (about) Symptom
23-113
1 RED ILL ( )
Ground for
illumination light With full dash
lights brightness,
0VIf open: When brightness = Auto, night mode for the
display is inoperative when lights on.
If short to ground: No change to display.
9 BLK RADIO GND (Ground)Ground for display
unit 0 V
If open: No change to display.
If short to ground: No change to display.
10 GRY ILL ( ) (Illumination
positive)Parking light on
signal from dash
and console lights Light on =
battery voltage,
Lights off = 0 VIf open: When brightness = Auto, night mode for the
display is inoperative when lights on.
If short to ground: Blows fuse No. 14 (7.5 A) in
under-dash fuse/relay box.
13 BLU VSP (Vehicle speed
pulse)Vehicle speed
pulse signal from
ECM/PCM Pulses 0 5 V:
Average 2.5 V,
when movingIf open: No vehicle speed pulses.
Diagnostic screen Car Status, VSP Navi = 0.
If short to ground: No vehicle speed pulses.
Diagnostic screen Car Status, VSP Navi = 0.
17 WHT B ( B power
source)Continuous power
source
Battery voltage If open: Screen completely off (no backlight visible).
If short to ground: Blows fuse No. 23 (10 A) in the
under-hood fuse/relay box.
(cont’d)
Wire side of female terminals
08/08/21 14:06:30 61SNR030_230_0116
ProCarManuals.com
DYNOMITE -2009-

´µ
Î

Navigation Unit Inputs and Outputs for Connector C (12P)
Navigation Unit Connector C (12P)TerminalNumber Wire Color Terminal Name Description Voltage (about) Symptom
23-114Navigation System
System Description (cont’d)
1 WHT B BACK UP Continuous power
sourceBattery voltage If open: Display picture goes out (display back light
still on). NOTE: System will reboot to enter code
screen.
If short to ground: Blows fuse No. 23 (10 A) in the
under-dash fuse/relay box.
4 BLK GND Ground for navigation unit0 V If open: No effect on system.
If short to ground: No effect on system.
7 BRN BACK LT Reverse signal of select laver from
Multiplex
integrated Control
unit (A/T) or
backup light switch
(M/T)In reverse,
battery voltage:
Otherwise0V
If open: Navigation never sees the reverse signal
and back-up camera does not come on when in
reverse. Diagnostic screen Car Status, Back = 0.
If short to ground: Blows fuse No. 10 (7.5 A) in the
under-dash fuse/relay box.
Wire side of female terminals
08/08/21 14:06:30 61SNR030_230_0117
ProCarManuals.com
DYNOMITE -2009-

Î
Î
(#'#
)
´
µ
µ
µ
µ µ
µ
µ
µ
No picture is displayed
YES
NO
YES
NO YES
NO
YES
NO
23-119
Symptom Troubleshooting
NAVIGATION UNIT CONNECTOR A (17P)
BBACKUP(WHT)
NAVIGATION UNIT CONNECTOR A (17P) ACC RADIO (PUR)
NOTE: Check the vehicle battery condition first.
 Make sure that the correct DVD color and version are installed.
 Check any official Honda service website for more service information about the navigation system.
 Check the connectors for poor connections or loose terminals.
 Before troubleshooting, make sure you have the navigation system anti-theft code.
1. Check the No. 23 (10 A) fuse in the under-hood fuse/relay box and No. 35 (7.5 A) fuse in the under-
dash fuse/relay box, and reinstall the fuse if it is OK.
Go to step 2.
Replace the fuse and recheck.
2. Turn the ignition switch to ON (II).
3. Operate the radio and listen to the audio.
Go to step 4.
Refer to audio system troubleshooting.
4. Turn the ignition switch to LOCK (0).
5. Remove the navigation unit (see page 23-155). 6. Measure the voltage between navigation unit
connector A (17P) terminal No. 17 and body ground.
Go to step 7.
Repair open in the wire between the under-
dash fuse/relay box and the navigation unit.
7. Turn the ignition switch to ON (II).
8. Measure the voltage between navigation unit connector A (17P) terminal No. 14 and body ground.
Go to step 9.
Repair open in the wire between the under-
dash fuse/relay box and the navigation unit.
(cont’d)
Wire side of female terminals
Wire side of female terminals
IsthefuseOK? Can y ou hear t he aud i o? Is there battery voltage?
Is there battery voltage?
08/08/21 14:07:25 61SNR030_230_0122
ProCarManuals.com
DYNOMITE -2009-

(#'#
)

µ
µ
µ
µ
YES
NO
YES
NO
Navigation display buttons do not work or
respond properly
23-12123-121
5. Turn the ignition switch to LOCK (0), then turn toON (II) and observe the navigation picture.
Check for sources of electrical noise, such as
poor battery connection, alternator, defective
battery, aftermarket accessories or cell phone, and
poor pin fits at the navigation unit.
Replace the navigation unit (see page 23-155). NOTE:
 Check the vehicle battery condition first.
 Always make sure that the correct DVD color and version are installed.
 Check any official Honda service website for more service information about the navigation system.
 Always check the connectors for poor connections or loose terminals.
 Before troubleshooting, make sure you have the navigation and audio system anti-theft codes.
1. Turn the ignition switch to ON (II).
Replace the navigation unit (see page 23-155).
Refer to troubleshooting for no picture is
displayed (see page 23-119).
Di d t he i mage i mpr ov e?
Does t he nav i gat i on d i spl ay t ur n on?
08/08/21 14:07:26 61SNR030_230_0124
ProCarManuals.com
DYNOMITE -2009-

(#'#
)(#'#
)

µ
µ
µ
µ µ
µ
µ
µ
µ
µ
µ
µ
GPS icon is white or not shown Voice guidance cannot be heard, is broken
up, or there is static
YES
NO
YES
NO YES
NO
YES
NO
YES
NO
YES
NO
23-12223-122Navigation System
Symptom Troubleshooting (cont’d)
NOTE:
 Check the vehicle battery condition first.
 Make sure the vehicle is parked outside and away from buildings.
 Refer to GPS Information (see page 23-142) for realtime satellite reception display.
 Check for window tinting above the GPS antenna and any non-OEM accessories mounted near the
navigation unit or GPS antenna.
1. Check for metallic window tint on the windshield and electronic aftermarket accessories (possibly
hidden) mounted near the GPS antenna or the
navigation unit.
Remove tint or the accessories, and
recheck.
Go to step 2.
2. Go into the Diagnostic Menu, and use the Navi System Link test (see page 23-136) to check the
GPS antenna.
Use the Navi ECU test under Unit Check
(see page 23-139) to check for a kinked, crushed, or
disconnected GPS antenna wire. If necessary, try a
known-good GPS antenna. If icon is still red,
replace the navigation unit (see page 23-155).
Check that nothing is blocking the GPS
antenna located behind the gauge assembly, and
recheck. Substitute a known-good navigation unit,
and recheck. NOTE:
 Check the vehicle battery condition first.
 Make sure that the correct DVD color and version are installed.
 Check any official Honda service website for more service information about the navigation system.
 Check that the volume setting and voice feedback are turned ON.
 Check the connectors for poor connection or loose terminals.
 Before troubleshooting, make sure you have the navigation system 4-digit anti-theft code.
 After troubleshooting, enter the navigation system anti-theft code.
1. Press the display unit SET-UP button.
2. Check the volume setting for the navigation system.
Set the volume to an audible level.
Go to step 3.
3. Check the radio operation.
Go to step 4.
Troubleshoot the audio system.
4. Go into the Diagnostic Menu, and use the Navi System Link test (see page 23-136) to check the
radio.
Troubleshoot the audio system.
Go to step 5.
5. Test the voice control switch (see page 23-156).
Replace the navigation unit (see page 23-155).
Replace the voice control switch (see page
23-157).
Is there metallic window tint or electronic accessor ies?
Is the GPS Ant icon red? Is it set to OFF?
Can y ou hear t he r ad i o?
Is the Radio icon red?I s v oi ce cont r ol sw i t ch OK ?
08/08/21 14:07:26 61SNR030_230_0125
ProCarManuals.com
DYNOMITE -2009-

Î
(#'#
)
 µ
µ
µ
µ
µ
µ
Voice control does not work/respond
YES
NO
YES
NO
YES
NO
23-123
NAVIGATION UNIT CONNECTOR D (5P) NAVI GUIDE (GRN)
NOTE: Check the vehicle battery condition first.
 Make sure that the correct DVD color and version are installed.
 Check any official Honda service website for more service information about the navigation system.
 Check the connector for poor connection or loose terminals.
 Before troubleshooting, make sure you have the navigation system 4-digit anti-theft code.
 After troubleshooting, enter the navigation system anti-theft code.
Before assuming that a voice complaint is hardware
related, ensure that the voice control system is being
operated correctly.  Make sure you are on the correct screen when trying to issue a voice command. For instance, the
command ‘‘Find the nearest Italian Restaurant’’ only
works on a Map screen (See the Navigation System
Manual for a complete list of allowed voice
commands for the information being displayed.).
 Close the windows, moonroof, and doors.
 Set the fan speed to low (1 or 2).
 Adjust the air flow from the air conditioning vents so that they do not blow against the microphone on the
ceiling.
 Pause after pressing the navigation TALK button, then give a voice command clearly in a natural
speaking voice. If the system cannot recognize your
command, speak louder.
 If the microphone picks up voices other than yours, the system may not interpret your voice commands
correctly.
 If you speak a command with something in your mouth, or your voice is too husky, the system may
misunderstand your command.
 Compare the system operation with a known-good vehicle. Have more than one person test the system
operation. If the known-good vehicle performs the
same, it is a characteristic of the system. 1. Turn the ignition switch to ON (II).
2. Go into the Diagnostic Menu and use the Mic Level
test under Functional Setup (see page 23-147) to
check the operation of the navigation TALK and
navigation BACK buttons.
Go to step 10.
Go to step 3.
3. Turn the ignition switch to LOCK (0).
4. Do the voice control switch test (see page 23-156).
Go to step 5.
Replace the voice control switch.
5. Disconnect the cable reel 20P connector and navigation unit connector D (5P).
6. Check for continuity between body ground and navigation unit connector D (5P) terminal No. 4.
Repair short to body ground in the wire
between the navigation unit and the voice control
switch, or replace the cable reel.
Go to step 7.
(cont’d)
Wire side of female terminals
Ar e t he nav i gat i on T ALK and nav i gat i on BACKbut t ons oper at i onal ?
I s t he v oi ce cont r ol sw i t ch OK ?
Is there continuity?
08/08/21 14:07:26 61SNR030_230_0126
ProCarManuals.com
DYNOMITE -2009-

(#'#
)(#'#
)
µ
µ
µ
µ µ
µ
Vehicle position icon constantly leaves road,
moves erratically, or is displayed very far
from actual position Vehicle icon wanders across the map when
driving (does not follow a displayed road) or
map or vehicle ICON spins
YES
NO
YES
NO YES
NO
23-12623-126Navigation System
Symptom Troubleshooting (cont’d)
NOTE:
 Check the vehicle battery condition first.
 Make sure that the correct DVD color and version are installed.
 Check any official Honda service website for more service information about the navigation system.
 Check for aftermarket accessories.
1. Check the GPS icon on the navigation picture.
Do the troubleshooting for GPS icon is white
or not shown (see page 23-122).
Go to step 2.
2. Go into the Diagnostic Menu, and use the Yaw Rate test (see page 23-144) to check the yaw rate sensor.
3. Go into the Diagnostic Menu and use the Car Status test (see page 23-141) to check the vehicle speed
pulse.
The problem may be a normal characteristic.
Check to see if the problem occurs in the same
place. If it does, the problem could be in the
database. Compare to a known-good vehicle under
the same conditions. If you can duplicate the
problem, report it. Refer to the client Assistance
section of the Navigation User’s Guide, ‘‘Reporting
Errors’’.
If the problem is the yaw rate sensor, replace
the navigation unit (see page 23-155). If the
problem is the vehicle speed pulse, troubleshoot
the vehicle speed signal circuit. NOTE:
 Check the vehicle battery condition first.
 This symptom is usually caused by a defective yaw rate sensor. Perform this diagnostic when the vehicle
is cold and warm.
 Also refer to symptom troubleshooting for GPS icon is white or not shown (see page 23-122).
1. Go into the Diagnostic Menu, and use the Yaw Rate test (see page 23-144).
The system is OK.
Replace the navigation unit (see page 23-155).
I s t he GPS i con on t he map scr een?
Ar e t he y aw r at e sensor and v ehi cl e speed pul seOK ? Ar e the values cor r ect?
08/08/21 14:07:27 61SNR030_230_0129
ProCarManuals.com
DYNOMITE -2009-

(#'#
)µ
Î

(#'#
)
µ
µ
DVD read error messages System always comes up in in-line
diagnostic mode
YES
NO
23-12723-127
Start Diag Exit Diag
Navi.ECU
In Line Diag
GPS Antenna Display
Radio
DeleteDone
0
12
3
6
5
4
7 8
9
BACK
XXXX Correct PIN
KA
NOTE:
 Check the vehicle battery condition first.
 Make sure that the correct DVD color and version are installed.
 Check any official Honda service website for more service information about the navigation system.
 Check the Navigation System Manual for a list of common DVD screen error messages and the
probable cause.
 Go into the Diagnostic Menu, and use the Car Status test (see page 23-141) to check the status of the
display.
1. Check the DVD-ROM reading surface for scratches.
Replace the DVD-ROM.
If the problem occurs occasionally when the
system is cold, this is normal. If the problem occurs
frequently when driving, replace the navigation
unit (see page 23-155). 1. When a navigation unit is powered up for the first
time at the factory, the factory diagnosis screen (In
Line Diag) appears. Normally the factory performs
the steps necessary to verify proper operation and
terminate the factory diagnostic. Until the proper
confirmation sequence is performed, the screen
will appear every time the vehicle is started.
2. Follow the steps to prevent the screen from showingupinthefuture:
 Hold down the buttons (Menu, Map/Guide, and Cancel) for about 5 seconds (the Select Diagnosis
Items screen appears).
 Hold down the Map/Guide button for 5 10 seconds (A screen with a Complete button
appears).
 Touch Complete, and then the Return button (the system may re-boot).
 Restart the vehicle, and confirm normal operation by completing the PDI of the
navigation system Service Bulletin.
Are there scratches?
08/08/21 14:07:27 61SNR030_230_0130
ProCarManuals.com
DYNOMITE -2009-