2005 TOYOTA AVENSIS brake light

056T1±03
F45086
Stop Lamp SwitchDLC3
Yaw Rate Sensor
(Include Lateral Acceleration Sensor) TRC OFF
Switch
Parking Brake Switch
Skid Control
BuzzerSkid Control Sensor
Left Front
Speed Sensor
Brake Actuator
(Include Skid Control ECU)
Combination Meter
(ABS Warning Light)
(Brake Warning Light)
(VSC Warning Light)
(TRC OFF Indicator Light)
(SLIP Indicator Light)
Speed Sensor Rotor
Steering Angle Sensor
ECM
± DIAGNOSTICSABS WITH EBD & BA & TRC & VSC SYSTEM
05±769
AVENSIS REPAIR MANUAL (RM1018E)
LOCATION

0542Q±04
05±766
±
DIAGNOSTICS ABS WITH EBD & BA & TRC & VSC SYSTEM
AVENSIS REPAIR MANUAL (RM1018E)
DIAGNOSTIC TROUBLE CODE CHART
HINT:

Using SST 09843±18040, connect the terminal Tc and CG of the DLC3.

If malfunction is not found when inspecting parts, inspect the ECU and grou\
nd points for poor contact.

If a malfunction code is displayed during the DTC check, check the circuit\
listed for that code. For de-
tails of each code, refer to the ºSee pageº for respective ºDTC No.º\
in the DTC chart.

When 2 or more DTCs are detected, perform circuit inspection one by one unti\
l the problem is identi-
fied.
DTC chart of ABS system:
DTC No.
(See Page)Detection ItemTrouble Area
C0200 / 31 (05±774)Right front wheel speed sensor signal malfunction

Right front speed sensor

Right front speed sensor circuit

Right front speed sensor rotor
C0205 / 32
(05±774)Left front wheel speed sensor signal malfunction

Left front speed sensor

Left front speed sensor circuit

Left front speed sensor rotor
C0210 / 33
(05±778)Right rear wheel speed sensor signal malfunction

Right rear speed sensor

Right rear speed sensor circuit

Right rear speed sensor rotor
C0215 / 34
(05±778)Left rear wheel speed sensor signal malfunction

Left rear speed sensor

Left rear speed sensor circuit

Left rear speed sensor rotor
C0226 / 21
(05±782)Open or short circuit in brake actuator
Brake actuator

SFRR or SFRH circuit
C0236 / 22
(05±782)Open or short circuit in brake actuator
Brake actuator

SFLR or SFLH circuit
C0246 / 23
(05±782)Open or short circuit in brake actuator
Brake actuator

SRRR or SRRH circuit
C0256 / 24
(05±782)Open or short circuit in brake actuator
Brake actuator

SRLR or SRLH circuit
C0273 / 13
(05±784)Open or short circuit in ABS motor relay circuit
ABS motor relay

ABS motor relay circuit
C0278 / 11
(05±787)Open or short circuit in ABS solenoid relay circuit
ABS solenoid relay

ABS solenoid relay circuit
C1237 / 37
(05±807)Wrong tire size
Tire size

Speed sensor rotor
C1241 / 41
(05±808)Low battery positive voltage or abnormally high battery positive
voltage
Battery

Charging system

Power source circuit
C1249 / 58
(05±815)Open circuit in stop light switch circuit
Stop lamp switch

Stop lamp switch circuit
C1300 / 62
(05±819)Malfunction in skid control ECU
Battery

Skid control ECU
C1330 / 35
(05±774)Open circuit in right front speed sensor circuit
Right front speed sensor

Right front speed sensor circuit
C1331 / 36
(05±774)Open circuit in left front speed sensor circuit
Left front speed sensor

Left front speed sensor circuit
C1332 / 38
(05±778)Open circuit in right rear speed sensor circuit
Right rear speed sensor

Right rear speed sensor circuit

±
DIAGNOSTICS ABS WITH EBD & BA & TRC & VSC SYSTEM
05±767
AVENSIS REPAIR MANUAL (RM1018E)C1333 / 39
(05±778)
Open circuit in left rear speed sensor circuit
Left rear speed sensor

Left rear speed sensor circuit
Always ON
(05±827)Malfunction in skid control ECU
Open circuit in ABS warning light circuit

Battery

Charging system

Power source circuit

Skid control ECU
DTC chart of VSC system:
DTC No.
(See Page)Detection ItemTrouble Area
C0365 / 43 (05±790)Malfunction in lateral acceleration sensor (combined in yaw
rate sensor)
Yaw rate sensor

Yaw rate sensor circuit
C0371 / 55
(05±793)Malfunction in yaw rate sensor circuit
Yaw rate sensor

Yaw rate sensor circuit
C1224 / 44
(05±797)Open or short circuit in NE signal circuit

NEO circuit

ECM

Skid control ECU
C1201/45
(05±796)VSC shut down due to ECM failure
ECM
C1203 / 59
(05±799)ECM communication circuit malfunction

TRC+ or TRC± circuit

ENG+ or ENG± circuit

ECM
C1208 / 54
(05±801)Malfunction in steering angle sensor
Steering angle sensor

Steering angle sensor circuit
C1225 / 25
(05±805)Open or short circuit in brake actuator solenoid circuit (SMC1
circuit)
Brake actuator

SMC1 circuit
C1226 / 26
(05±805)Open or short circuit in brake actuator solenoid circuit (SMC2
circuit)
Brake actuator

SMC2 circuit
C1227 / 27
(05±805)Open or short circuit in brake actuator solenoid circuit (SRC1
circuit)
Brake actuator

SRC1 circuit
C1228 / 28
(05±805)Open or short circuit in brake actuator solenoid circuit (SRC2
circuit)
Brake actuator

SRC2 circuit
C1246 / 53
(05±812)Malfunction in master cylinder pressure sensor
Master cylinder pressure sensor

Master cylinder pressure sensor circuit
C1288 / 88
(05±818)Malfunction in ECM version
Steering angle sensor zero point calibration
C1301 / 42
(05±821)Malfunction in CAN communication circuit
(steering angle sensor circuit, yaw rate sensor circuit)
Steering angle sensor circuit

Yaw rate sensor circuit
C1350 / 51
(05±825)Pump motor is locked
Open circuit in pump motor ground
Brake actuator pump motor
Always ON
(05±831)Malfunction in skid control ECU
Open circuit in VSC warning light circuit

Battery

Charging system

Power source circuit

Skid control ECU

0577Y±02
F45094
ABS Warning LightBRAKE Warning
Light
VSC Warning Light SLIP Indicator Light
TRC OFF Indicator
Light
C52361
DLC3 Tc
CG
05±756
±
DIAGNOSTICS ABS WITH EBD & BA & TRC & VSC SYSTEM
AVENSIS REPAIR MANUAL (RM1018E)
PRE±CHECK
1.DIAGNOSIS SYSTEM
(a)Check the warning lights. (1)Release the parking brake lever.
(2)When the ignition switch is turned ON, check thatthe ABS warning light, Brake warning light, VSC
warning light, TRC OFF indicator light and SLIP in-
dicator light come on for approx. 3 seconds.
HINT:

When the parking brake is applied or brake fluid level is
low, the Brake warning light comes on.

If the ECU stores DTC, the ABS warning light , VSC warn-
ing light and TRC OFF indicator light come on.

If the indicator check result is not normal, proceed to trou-
bleshooting for the light circuit.
Trouble AreaSee page
ABS warning light circuit05±827
Brake warning light circuit05±840
VSC warning light circuit05±831
TRC OFF indicator light circuit05±844
SLIP indicator light circuit05±848
(b) Without using hand±held tester: Check the DTC.
(1) Using SST, connect terminal Tc and CG of theDLC3.
SST 09843±18040
(2) Turn the ignition switch ON.
(3) Read the DTC from the ABS warning light or VSC warning light on the combination meter.
HINT:

If no code appears, inspect the diagnostic circuit, ABS
warning light circuit or VSC warning light circuit.
Trouble AreaSee page
Tc terminal circuit05±852
ABS warning light circuit05±827
VSC warning light circuit05±831

R01346
Normal Code
Code 1 1 and 21
ON
OFF
4 sec.0.5 sec.
1.5 sec.
2.5 sec. 0.5 sec.
2 sec.
0.25 sec.
0.25 sec.
ON
OFF
Cod e 1 1 Code 21
BR3890
±
DIAGNOSTIC SABS WITH EBD & BA & TRC & VSC SYSTEM
05±757
AVENSIS RE PAIR MANUAL (RM1018E)

A s an example, the blinking patterns for the normal code
an d codes 11 and 21 are shown on the left.
(4 ) Codes are explained in the code table on page
05±766.
(5) After completing the check, disconnect terminal Tc and CG of the DLC3, and turn off the display.
If 2 or more DTCs are detected at the same time, the lowest
numbered DTC is displayed first.
(c) With using the hand±held tester:
Check the DTC.
(1) Hook up the hand±held tester to the DLC3.
(2) Turn the ignition switch ON.
(3) Read the DTC by following the prompts on the tes-ter screen.
HINT:
Please refer to the hand±held tester operator's manual for fur-
ther details.
(d) Without using hand±held tester: Clear the DTCs.
(1) Using SST, connect the terminal Tc and CG of theDLC3.
SST 09843±18040
(2) Turn the ignition switch ON.
(3) Clear the DTCs stored in the ECU by depressing the
brake pedal 8 or more times within 5 seconds.
(4) Check that the ABS warning light and VSC warning
light indicates the normal code blinking pattern.
(5) Remove the SST from the DLC3.
SST 09843±18040
HINT:
Disconnecting the battery cable during repairs will not erase the
DTCs in the ECU.
(e) With using hand±held tester: Clear the DTCs.
(1) Turn the ignition switch ON.
(2) Operate the hand±held tester to erase the codes.
HINT:
Please refer to the hand±held tester operator's manual for fur-
ther details.

05±758
± DIAGNOSTICSABS WITH EBD & BA & TRC & VSC SYSTEM
AVENSIS REPAIR MANUAL (RM1018E)
2. DATA LIST
HINT:
According to the DATA LIST displayed on the Hand±held tester, you can read the value and status of the
switch, sensor, actuator and so on without parts removal. Reading the DATA LIST as a first step of trouble-
shooting is one of the methods to shorten the labor time.
(a) Connect the Hand±held tester to the DLC3.
(b) Turn the ignition switch ON.
(c) From the display on the tester, read the ºDATA LISTº.
ItemMeasurement Item /
Range (Display)Normal ConditionDiagnostic Note
ABS MOT RELAYABS motor relay / ON or
OFFON : Motor relay ON±
SOL RELAYSolenoid relay / ON or
OFFON : Solenoid relay ON±
VSC / TRC OFF SWVSC / TRC OFF switch /
ON or OFFON : Switch ON
OFF : Switch OFF±
STOP LIGHT SWStop light switch / ON or
OFF
ON : Brake pedal de-
pressed
OFF : Brake pedal re-
leased
±
PKB SWParking brake switch / ON
or OFFON : Parking brake applied
OFF : Parking brake re-
leased
±
WHEEL SPD FR
Wheel speed sensor (FR)
reading / min.: 0 km/h (0
MPH, max.: 326 km/h (202
MPH)
Actual wheel speedSpeed indicated on
speedometer
WHEEL SPD FL
Wheel speed sensor (FL)
reading / min.: 0 km/h (0
MPH, max.: 326 km/h (202
MPH)
Actual wheel speedSpeed indicated on
speedometer
WHEEL SPD RR
Wheel speed sensor (RR)
reading / min.: 0 km/h (0
MPH, max.: 326 km/h (202
MPH)
Actual wheel speedSpeed indicated on
speedometer
WHEEL SPD RL
Wheel speed sensor (RL)
reading / min.: 0 km/h (0
MPH, max.: 326 km/h (202
MPH)
Actual wheel speedSpeed indicated on
speedometer
DECELERAT SENS1
Lateral acceleration sensor
1 reading / min.: ±1.869 G,
max.: 1.869 GApproximately 0
0.1G at
still conditionReading changes when ve-
hicle is bounced
IG VOLTAGEECU power supply voltage
/ NORMAL or TOO LOWNORMAL : 9.8 V or over
TOO LOW : Below 9.8 V±
SFRRABS solenoid SFRR / ON
or OFFON : Operate±
SFRHABS solenoid SFRH / ON
or OFFON : Operate±
SFLRABS solenoid SFLR / ON
or OFFON : Operate±
SFLHABS solenoid SFLH / ON
or OFFON : Operate±
SRRR (SRR)ABS solenoid SRRR
(SRR) / ON or OFFON : Operate±
SRRH (SRH)ABS solenoid SRRH
(SRH) / ON or OFFON : Operate±

± DIAGNOSTICSABS WITH EBD & BA & TRC & VSC SYSTEM
05±761
AVENSIS REPAIR MANUAL (RM1018E)
ItemDiagnostic Note Vehicle Condition / Test Details
SRH & SRRTurns ABS solenoid SRH & SRR ON / OFF
Operation of solenoid
(clicking sound) can be
heard
SRLR & SRLHTurns ABS solenoid SRLR & SRLH ON / OFF
Operation of solenoid
(clicking sound) can be
heard
SFRH & SFLHTurns ABS solenoid SFRH & SFLH ON / OFF
Operation of solenoid
(clicking sound) can be
heard
SRCF & SRCRTurns ABS solenoid SRCF & SRCR ON / OFF
Operation of solenoid
(clicking sound) can be
heard
SRMF & SRMRTurns ABS solenoid SRMF & SRMR ON / OFF
Operation of solenoid
(clicking sound) can be
heard
SOL RELAYTurns ABS solenoid relay ON / OFF
Operation of solenoid
(clicking sound) can be
heard
ABS MOT RELAYTurns ABS motor relay ON / OFFOperation of motor can be
heard
ABS WARN LIGHTTurns ABS warning light ON / OFFObserve combination me-
ter
VSC WARN LIGHTTurns VSC warning light ON / OFFObserve combination me-
ter
VSC / TRC OFF INDTurns VSC / TRC OFF indicator ON / OFFObserve combination me-
ter
SLIP INDI LIGHTTurns SLIP indicator light ON / OFFObserve combination me-
ter
BRAKE WRN LIGHTTurns BRAKE warning light ON / OFFObserve combination me-
ter
VSC WARN BUZTurns VSC warning buzzer ON / OFFBuzzer can be heard

05±762
± DIAGNOSTICSABS WITH EBD & BA & TRC & VSC SYSTEM
AVENSIS REPAIR MANUAL (RM1018E)
4. FREEZE FRAME DATA
(a) The vehicle (sensor) status memorized during ABS and/or VSC operation or at the time of error code
detection can be displayed using the hand±held tester.
(b) Only one record of the freeze frame data is stored and the freeze frame data generated during ABS
and/or VSC operation are constantly updated. Also, the number of the operations of the ignition switch
ºONº after the freeze frame data is stored can be memorized up to 31 and it can be displayed.
HINT:
If the ignition switch ºONº operation exceeds 31 times, º31º appears on the display.
(c) If the diagnosis code malfunction occurs, the freeze frame data at the occurrence of the malfunction
is stored but the ABS actuation data is deleted.
Hand±held tester displayMeasurement ItemReference Value*
VEHICLE SPDVehicle speedSpeed indication of a meter
STOP LIGHT SWStop light switch signalStop light switch ON: ON, OFF: OFF
# IG ONNumbers of operations of ignition switch ON after
memorizing freeze frame data0 to 31
MAS CYL PRESSMaster cylinder pressure sensor output voltageRelease brake pedal: 0.3 to 0.9 V
Depress brake pedal: 1.5 to 4.5 V
MASS PRESS GRADEMaster cylinder pressure sensor changing gradi-
ent±30 to 200 MPa/s
SYSTEMOperate system
ABS operate: ABS
BA operate: BA
VSC (TRC) operate: VSC (TRC)
YAW RATEYaw rate angle sensor output value±70 to 70
STEERING ANGSteering sensor output valueLeft turn: Increase
Right turn: Drop
THROTTLEThrottleposition sensor output valueRelease accelerator pedal: Approx. 0 degTHROTTLEThrottle position sensor output valueRelease accelerator edal: A rox. 0 deg
Depress accelerator pedal: Approx. 90 deg
G (RIGHT & LEFT)Right and left G±1.869 to 1.869 G
VSC (TRC) OFF SWTRC OFF switch signalTRC OFF SW ON: ON
OFF: OFF
SHIFT POSITIONShift lever position
P: P
R: R
N: N
D: D
2: 2
L: L
*: If no conditions are specifically stated for ºIdlingº, it means the shift lever is at N or P position, the A/C switch
is OFF and all accessory switches are OFF.