2005 PORSCHE CAYENNE TURBO PORSCHE CAYNNE TURBO 2005 1.G Owners Manual

Practical Tips, Minor Repairs
329
Headlights
Caution!
Risk of damage to headlights due to abrasion
and excessive temperatures.
fDo not affix any coverings (e.g. “stone guards” or films) in the area of the headlights.
Removing Bi-Xenon headlight1. Switch off ignition and withdraw the ignition
key.
2. Push down cover A in the direction of the arrow
and remove.
B- Headlight release
C-Wing
D- Socket wrench3. Take socket wrench D out of the tool kit.
4. Push socket wrench D onto the release B and
turn in the direction of the arrow.
The headlight holder has now been unlocked.
5. Pull headlight forward out of the fender.

330
Practical Tips, Minor Repairs
B- Headlight release
C-Wing
D- Socket wrenchB- Headlight release
C-Wing
D-Socket wrench
Installing Bi-Xenon headlights1. Insert headlight into the guide rails and push
fully into the fender.
2. Push headlight to the rear and simultaneously
turn socket wrench D in the direction of the ar-
row.
The headlight locking device must perceptibly
and audibly engage.
B- Headlight release
C-Wing
D-Socket wrench3. Check whether the headlights are seated se-
curely.
4. Fit cover A and fold it down.

Practical Tips, Minor Repairs
331
Location of bulbs in Bi-Xenon headlightsBi-Xenon headlight
F Bulb for turn signal
G Bulb for additional high beam
H Bulb for cornering light
I Bulb for side light
J Xenon gas discharge lamp for low beam and
high beam
Opening the lid of the headlight housing1. Open both clips A.
2. Remove housing lid B.
Closing lid of headlight housing1. Put housing lid B on and press into place.
2. Close clips A.

332
Practical Tips, Minor Repairs
Changing the gas discharge lamp1. Pull off plug J.
2. Unclip securing clip G.
3. Pull off holder H.
4. Replace defective bulb.
Note on operation
fMake sure the bulb is installed in the correct
position.
Reassemble in reverse order.
Changing bulb for cornering light1. Pull plug off the bulb (arrow).
2. Unclip securing clip I.
3. Replace defective bulb.
Note on operation
fMake sure the bulb is installed in the correct
position.
4. Reassemble in reverse order.Changing side light bulb in Bi-Xenon
headlight
1. Pull out the lamp for low beam and high beam.
2. Pull the bulb holder out of lamp bracket.

Practical Tips, Minor Repairs
333
3. Pull bulb out of the holder (arrow).
4. Replace defective bulb.
5. Reassemble in reverse order.Changing additional high beam light
1. Remove cover G.2. Pull plug J off the bulb.
3. Unclip securing clip H.
4. Pull bulb I out.
5. Replace defective bulb.
Note on operation
fMake sure the bulb is installed in the correct
position.
6. Reassemble in reverse order.

334
Practical Tips, Minor Repairs
Changing turn signal bulb1. Turn bulb holder in the headlight housing anti-
clockwise and pull it out.2. Remove bulb from the holder (bayonet lock):
Push bulb into the holder and twist in the
direction of the arrow.
3. Replace defective bulb.
4. Insert bulb holder into the headlight housing
and turn it clockwise until it engages.

Practical Tips, Minor Repairs
335
Tail LightRemoving tail lightMaintenance note
fThe ignition key must be withdrawn before the
tail light is removed.
1. Open rear lid.
2. Remove the two caps A with a tool such as a
screwdriver.
3. Unscrew the two fastening screws B with the
socket wrench from the tool kit.4. Pull out the light unit to the side in the direc-
tion of the arrow and additionally pull it out in
the area of the ball head C.
5. On the plug connection D press on the plug re-
lease (arrow) and pull off the plug.
Installing tail light1. Push on plug connection D until the plug is felt
to click into place (arrow).
2. Insert ball head of tail light C into clip nut E and
fit the light unit into the body (arrow).
f f f

336
Practical Tips, Minor Repairs 3. Screw in the fastening screws B.
4. Press in caps A.
Replacing bulbs1. Undo fastening screws C of the housing cover.
2. Remove housing cover D.
E- Rear fog light and tail light
F- Reversing light
G- Turn signal light
H- Brake light
I- Tail light3. Replace defective bulb.
4. Insert lamp bracket.
5. Install tail light.