2005 NISSAN X-TRAIL Rear wiper

MODEL T30 SERIES
2005 NISSAN EUROPE S.A.S.
All rights reserved. No part of this Electronic Service Manual may be reproduced or stored in a retrieval system, or transmitted in any
form, or by any means, electronic, mechanical, photocopying, recording or otherwise, without the prior written permission of Nissan
Europe S.A.S., Paris, France.
A GENERAL INFORMATION
B ENGINE
C TRANSMISSION/TRANSAXLE
D DRIVELINE/AXLE
E SUSPENSION F BRAKES
G STEERING H RESTRAINTS
I BODY
J AIR CONDITIONER
K ELECTRICAL
L MAINTENANCE
M INDEXGI General Information
EM Engine Mechanical
LU Engine Lubrication System
CO Engine Cooling System
EC Engine Control System
FL Fuel System
EX Exhaust System
ACC Accelerator Control System
CL Clutch
MT Manual Transaxle
AT Automatic Transaxle
TF Transfer
PR Propeller Shaft
RFD Rear Final Drive
FAX Front Axle
RAX Rear Axle
FSU Front Suspension
RSU Rear Suspension
WT Road Wheels & Tires
BR Brake System
PB Parking Brake System
BRC Brake Control System
PS Power Steering System
SB Seat Belts
SRS Supplemental Restraint System (SRS)
BL Body, Lock & Security System
GW Glasses, Window System & Mirrors
RF Roof
EI Exterior & Interior
IP Instrument Panel
SE Seat
ATC Automatic Air Conditioner
MTC Manual AIr Conditioner
SC Starting & Charging System
LT Lighting System
DI Driver Information System
WW Wiper, Washer & Horn
BCS Body Control System
LAN LAN System
AV Audio Visual, Navigation & Telephone System
ACS Auto Cruise Control System
PG Power Supply, Ground & Circuit Elements
MA Maintenance
IDX Alphabetical Index
QUICK REFERENCE INDEX
A
B
C
D
E
F
G
H
I
J
K
L
M

BACK DOOR WINDOW GLASS
GW-15
C
D
E
F
G
H
J
K
L
MA
B
GW

BACK DOOR WINDOW GLASSPFP:90300
Removal and InstallationEIS0045K
REMOVAL
1. Remove rear wiper arm. Refer to WW-16, "Removal and Installation of Rear Wiper Arms" .
2. Remove rear washer nozzle. Refer to WW-18, "
Removal and Installation of Rear Washer Nozzle" .
3. Remove rear defogger connectors.
4. Apply a protective tape around the back door window glass to prevent the paint surface from being dam-
aged.
5. Cut adhesive using piano wire or power cutting tool and an inflatable pump bag.
WARNING:
When cutting the glass from the vehicle, always wear safety glasses and heavy gloves to help prevent
glass splinters from entering your eyes or cutting your hands.
CAUTION:

When a windshield glass is to be reused, do not use a cutting knife or power cutting tool.

Be careful not to scratch the glass when removing.

Do not set or stand the glass on its edge. Small chips may develop into cracks.
PIIB0582E
PIIB0415E

WW-1
WIPER, WASHER & HORN
K ELECTRICAL
CONTENTS
C
D
E
F
G
H
I
J
L
M
SECTION WW
A
B
WW

WIPER, WASHER & HORN
PRECAUTIONS .......................................................... 3
Precautions for Supplemental Restraint System
(SRS) “AIR BAG” and “SEAT BELT PRE-TEN-
SIONER” .................................................................. 3
Wiring Diagrams and Trouble Diagnosis .................. 3
FRONT WIPER AND WASHER SYSTEM .................. 4
System Description .................................................. 4
WIPER OPERATION ............................................ 4
WASHER OPERATION ......................................... 5
Wiring Diagram — WIPER — .................................. 6
Wiring Diagram — WIPER —/LHD models .............. 7
Terminal and Reference Values for Combination
Switch ....................................................................... 8
Removal and Installation of Front Wiper Arms,
Adjustment for Wiper Arms Stop Location ............... 8
Removal and Installation of Front Wiper Drive
Assembly .................................................................. 9
REMOVAL ............................................................. 9
INSTALLATION ................................................... 10
Front Washer Nozzle Adjustment ............................ 11
Washer Tube Layout ............................................... 11
Removal and Installation of Front Washer Nozzle ... 12
REMOVAL ........................................................... 12
INSTALLATION ................................................... 12
Inspection for Front Washer Nozzle ....................... 12
CHECK VALVE ................................................... 12
Removal and Installation of Wiper and Washer
Switch ..................................................................... 12
REMOVAL ........................................................... 12
INSTALLATION ................................................... 12
Removal and Installation of Washer Tank .............. 13
REMOVAL ........................................................... 13
INSTALLATION ................................................... 13
Removal and Installation of Washer Motor ............ 13
REMOVAL ........................................................... 13
INSTALLATION ................................................... 13
REAR WIPER AND WASHER SYSTEM .................. 14
Wiring Diagram — WIP/R — .................................. 14
Terminal and Reference Values for Combination
Switch ..................................................................... 16Removal and Installation of Rear Wiper Arms ........ 16
WIPER ARMS ..................................................... 16
Removal and Installation of Rear Wiper Motor ....... 17
REMOVAL ........................................................... 17
INSTALLATION ................................................... 17
Rear Washer Nozzle Adjustment ........................... 18
Removal and Installation of Rear Washer Nozzle ... 18
REMOVAL ........................................................... 18
INSTALLATION ................................................... 18
Inspection for Rear Washer Nozzle ........................ 18
CHECK VALVE .................................................... 18
Removal and Installation of Wiper and Washer
Switch ..................................................................... 19
Removal and Installation of Washer Tank .............. 19
Removal and Installation of Washer Motor ............. 19
Washer Tube Layout .............................................. 19
HEADLAMP WASHER ............................................. 20
System Description ................................................. 20
Wiring Diagram —HLC— ....................................... 21
Wiring Diagram —HLC—/RHD models .................. 23
Removal and Installation of Headlamp Washer Noz-
zle ........................................................................... 25
REMOVAL ........................................................... 25
INSTALLATION ................................................... 25
Inspection for Headlamp Washer Nozzle ............... 25
CHECK VALVE .................................................... 25
Removal and Installation of Washer Tank .............. 25
Removal and Installation of Washer Motor ............. 25
Washer Tube Layout .............................................. 26
HORN ........................................................................ 27
Wiring Diagram — HORN — .................................. 27
Removal and Installation ........................................ 28
REMOVAL ........................................................... 28
INSTALLATION ................................................... 28
CIGARETTE LIGHTER ............................................. 29
Wiring Diagram — CIGAR — ................................. 29
Removal and Installation ........................................ 30
REMOVAL ........................................................... 30
INSTALLATION ................................................... 30
POWER SOCKET ..................................................... 31

WW-14
REAR WIPER AND WASHER SYSTEM

REAR WIPER AND WASHER SYSTEMPFP:28710
Wiring Diagram — WIP/R —EKS0032Z
TKWA1556E

REAR WIPER AND WASHER SYSTEM
WW-15
C
D
E
F
G
H
I
J
L
MA
B
WW

TKWA1557E

WW-16
REAR WIPER AND WASHER SYSTEM

Terminal and Reference Values for Combination SwitchEKS00330
Removal and Installation of Rear Wiper Arms EKS00331
WIPER ARMS
1. Turn on wiper switch to operate wiper motor and then turn it
“OFF” (auto stop).
2. Lift the blade up and then set it down onto glass surface. Set the
black center to clearance “L” immediately before tightening the
nut.
3. Eject washer fluid. Turn on wiper switch to operate wiper motor
and then turn it “OFF”.
4. Ensure that wiper blades stop on the lowest heat wire.

Tighten wiper arm nut to specified torque.

Before reinstalling wiper arm, clean up the pivot area as illus-
trated. This will reduce possibility of wiper arm looseness.
Terminal
No.Wire
colorSignal name Measuring condition
Reference value
Ignition switch Condition or operation
21 WWiper motor
Operation signal (ON)ON Wiper switchOFF Battery voltage
ON Approx. 0V
22 LG/B Washer switch signal ON Wiper switchWASH Approx. 0V
OFF Battery voltage
23 BR/YWiper motor
Operation signalON Wiper switch: INT
24 B/W Ground OFF — —
SKIA0083J
Clearance “L” : 55.6 - 70.6 mm (2.189 - 2.780 in)
Rear wiper arm nuts
: 15.2 N·m (1.6 kg-m, 11 ft-lb)
SKIA0077E
SEL024J

REAR WIPER AND WASHER SYSTEM
WW-17
C
D
E
F
G
H
I
J
L
MA
B
WW

Removal and Installation of Rear Wiper MotorEKS00332
REMOVAL
1. Remove the back door finisher. Refer to EI-34, "BACK DOOR TRIM" .
2. Disconnect wiper motor connector.
3. Remove wiper arm from the vehicle.
4. Remove wiper motor form the vehicle.
5. Remove rubber from the vehicle.
INSTALLATION
1. Install rubber to the vehicle.
2. Install wiper motor to the vehicle.
3. Connect wiper motor to connector. Turn the rear wiper switch ON to operate wiper motor, then turn the
rear wiper switch OFF (auto stop).
4. Install wiper arm to the vehicle.
5. Install back door finisher. Refer to EI-34, "
BACK DOOR TRIM" .
CAUTION:

Never drop the wiper motor or cause it to contact other parts.

Check the grease conditions of the motor arm and wiper link joint (at retainer). Apply grease if
necessary.
1. Wiper motor 2. Rubber 3. Nut cover
4. Wiper arm 5. Wiper blade
PKIA7846E
SKIA0040E
Rear wiper motor mounting bolt
: 4.5 N·m (0.46 kg-m, 40 in-lb)

WW-18
REAR WIPER AND WASHER SYSTEM

Rear Washer Nozzle AdjustmentEKS00333

Adjust rear washer nozzle with suitable tool as shown in the figure at left.
Unit: mm (in)
*: The diameter of this circle is less than 40 mm (1.57in).
Removal and Installation of Rear Washer Nozzle EKS00334
REMOVAL
1. Remove washer hose from rear washer nozzle.
2. Remove rear washer nozzle mounting screw and remove rear
washer nozzle.
INSTALLATION
1. After connecting washer hose, press nozzle from cowl top cover surface.
2. Assemble nozzle and socket.
3. Adjust nozzle injection position.
Inspection for Rear Washer Nozzle EKS00335
CHECK VALVE
Blow air in the injection direction, and check that air flows only one
way. Make sure that the reverse direction (inhale) is not possible. Adjustable range : ±10° (In any direction)
PKIA0487E
*H 90 (3.54)
* L 150 (5.91)
SKIA0091E
PKIA5552E
SKIA0042E