2005 NISSAN X-TRAIL filter

LU-22
[YD22DDTi]
ENGINE OIL

3. Loosen oil filler cap and then remove drain plug.
4. Drain engine oil.
5. Install drain plug with new washer. Refer to EM-157, "
OIL PAN AND OIL STRAINER" .
CAUTION:
Be sure to clean drain plug and install with new washer.
6. Refill with new engine oil.
Engine oil specification and viscosity:
Refer to MA-17, "
RECOMMENDED FLUIDS AND LUBRICANTS" .
Engine oil capacity (Approximate):
Unit: (lmp qt)
CAUTION:

The refill capacity depends on the engine oil temperature and drain time. Use these specifica-
tions for reference only.

Always use the oil level gauge to determine the proper amount of engine oil in the engine.
7. Warm up engine and check area around drain plug and oil filter for oil leakage.
8. Stop engine and wait for 10 minutes.
9. Check the engine oil level. Refer to LU-20, "
ENGINE OIL LEVEL" .
PBIC0527E
Oil pan drain plug:
: 34 N·m (3.5 kg-m, 25 ft-lb)
Drain and refill With oil filter change 5.2 (4-5/8)
Without oil filter change 4.9 (4-3/8)
Dry engine (Overhaul)6.3 (5-1/2)

OIL FILTER
LU-23
[YD22DDTi]
C
D
E
F
G
H
I
J
K
L
MA
LU

OIL FILTER PFP:15208
Removal and Installation (TYPE A)EBS00B05
REMOVAL
1. Open oil filter installation/removal cover on RH engine undercover.
2. Using the oil filter wrench, remove oil filter.
CAUTION:

Be careful not to get burned when engine and engine oil are hot.

When removing, prepare a shop cloth to absorb any engine oil leakage or spillage.

Do not allow engine oil to adhere to drive belts.

Completely wipe off any engine oil that adhere to engine and vehicle.

Oil filter is provided with a relief valve.
INSTALLATION
1. Remove foreign materials adhering to the oil filter installation surface.
2. Apply new engine oil to the oil seal circumference of new oil fil-
ter.
3. Screw oil filter manually until it touches the installation surface, then tighten it by 1/2 turn. Or tighten to
specification.
INSPECTION AFTER INSTALLATION
1. Start engine, and check there is no leakage of engine oil.
2. Stop engine and wait for 10 minutes.
3. Check the engine oil level and adjust engine oil. Refer to LU-20, "
ENGINE OIL" .
SMA010
Oil filter:
: 18 N·m (1.8 Kg-m, 13 ft-lb)

LU-24
[YD22DDTi]
OIL FILTER

Removal and Installation (TYPE B)EBS011WI
REMOVAL
CAUTION:

Be careful not to get burned when engine and engine oil are
hot.

When removing, prepare a shop cloth to absorb any engine
oil leakage or spillage.

Do not allow engine oil to adhere to drive belts.

Completely wipe off any engine oil that adhere to engine
and vehicle.
1. Open oil filter installation/removal cover on RH engine undercover.
2. Using a socket wrench [plane-to-plane width: 17 mm (0.67 in)],
loosen oil filter body approximately four turns.
3. Drain engine oil after matching the "DRAIN" arrow mark at the
bottom of oil filter body to the protrusion on oil filter bracket.

Catch engine oil with a pan or cloth.
CAUTION:

The drained engine oil flows over the right surface of
oil filter body.

Completely wipe clean any engine oil remaining on oil
filter body or vehicle.
4. Remove oil filter body, then remove oil filter.
PBIC2536E
JLC290B
JLC291B

OIL FILTER
LU-25
[YD22DDTi]
C
D
E
F
G
H
I
J
K
L
MA
LU

5. Remove O-ring from oil filter body.

Push O-ring in one direction, lift the slack part using fingers,
and remove O-ring from oil filter body.
CAUTION:
Do not use a screwdrivers etc. as they may cause dam-
age to oil filter body.
INSTALLATION
1. Completely remove all foreign objects adhering to the inside of oil filter body or O-ring mounting area
(body side and bracket side).
2. Install oil filter and O-ring to oil filter body.

Push oil filter into filter body completely.
3. Install oil filter body to oil filter bracket.
INSPECTION AFTER INSTALLATION
1. After warming up engine, check there is no leaks of engine oil.
2. Stop engine and wait for 10 minutes.
3. Check the engine oil level and adjust engine oil. Refer to LU-20, "
ENGINE OIL" .
JLC292B
Oil filter body:
: 22 N·m (2.2 Kg-m, 16 ft-lb)

LU-26
[YD22DDTi]
OIL FILTER BRACKET

OIL FILTER BRACKETPFP:15238
Removal and Installation (TYPE A)EBS00BL8
REMOVAL
CAUTION:
Be careful not to get burned when engine is hot.
1. Remove RH engine undercover.
2. Remove oil filter. Refer to LU-23, "
Removal and Installation (TYPE A)" .
3. Remove oil filter bracket.
INSTALLATION
Install all removed parts in the reverse order of removal.

Insert the top mounting bolt to oil filter bracket beforehand, and set oil filter bracket to the installation loca-
tion.
INSPECTION AFTER INSTALLATION
1. After warming up engine, check there is no leaks of engine oil.
2. Stop engine and wait for 10 minutes.
3. Check the engine oil level and adjust engine oil. Refer to LU-20, "
ENGINE OIL" .
1. Oil pump housing 2. Gasket 3. Oil filter bracket
4. Oil filter
PBIC2380E

OIL FILTER BRACKET
LU-27
[YD22DDTi]
C
D
E
F
G
H
I
J
K
L
MA
LU

Removal and Installation (TYPE B)EBS011WJ
REMOVAL
CAUTION:
Be careful not to get burned when engine is hot.
1. Remove RH engine undercover.
2. Remove oil filter. Refer to LU-24, "
Removal and Installation (TYPE B)" .
3. Remove oil filter bracket.
INSTALLATION
Install all removed parts in the reverse order of removal.

Insert the top mounting bolt to oil filter bracket beforehand, and set oil filter bracket to the installation loca-
tion.
INSPECTION AFTER INSTALLATION
1. After warming up engine, check there is no leaks of engine oil.
2. Stop engine and wait for 10 minutes.
3. Check the engine oil level and adjust engine oil. Refer to LU-20, "
ENGINE OIL" .
1. Oil pump housing 2. Gasket 3. Oil filler bracket
4. Oil filler 5. O-ring 6. Oil filter body
PBIC2537E

SERVICE DATA AND SPECIFICATIONS (SDS)
LU-33
[YD22DDTi]
C
D
E
F
G
H
I
J
K
L
MA
LU

SERVICE DATA AND SPECIFICATIONS (SDS)PFP:00030
Standard and LimitEBS00CTZ
OIL PRESSURE
OIL PUMP
Unit: mm (in)
REGULATOR VALVE
Unit: mm (in)
OIL CAPACITY (APPROXIMATE)
Unit: · (Imp qt)
Tightening TorqueEBS00B0F
Unit: N·m (kg-m, ft-lb)
Unit: N·m (kg-m, in-lb)* Engine speed rpm
Approximate discharge pressure kPa (bar, kg/cm
2 , psi)
Idle speed
2,000140 (1.40, 1.43, 20.3) or more
270 (2.70, 2.75, 39.2) or more
Oil pump housing to outer rotor radial clearance 0.114 - 0.260 (0.0045 - 0.0102)
Inner rotor to outer rotor tip clearance Below 0.18 (0.0071)
Oil pump housing to inner rotor side clearance 0.050 - 0.090 (0.0020 - 0.0035)
Oil pump housing to outer rotor side clearance 0.030 - 0.190 (0.0012 - 0.0075)
Inner rotor to oil pump housing clearance 0.045 - 0.091 (0.0018 - 0.0036)
Regulator valve to valve hole clearance 0.040 - 0.097 (0.0016 - 0.0038)
With oil filter change 5.2 (4-5/8 Imp qt)
Without oil filter change 4.9 (4-3/8 Imp qt)
Dry engine (engine overhaul) 6.3 (5-1/2 Imp qt)
Oil pressure switch15 (1.5, 11)
Oil pan drain plug34 (3.5, 25)
Oil filter bracket21.5 (2.2, 16)
Oil filter (TYPE A)18 (1.8, 13)
Oil filler body (TYPE B) 22 (2.2, 16)
Oil pump cover Bolts 6.9 (0.7, 61)*
Screws 6.9 (0.7, 61)*
Regulator plug54 (5.5, 40)
Water hose connector 23.6 (2.4, 17)
Oil cooler24.5 (2.5, 18)

EC-10 CONSULT-II Reference Value in Data Monitor Mode
.946
Wiring Diagram .....................................................947
Diagnostic Procedure ...........................................948
Component Inspection ..........................................953
ASCD INDICATOR ..................................................954
Component Description ........................................954
CONSULT-II Reference Value in Data Monitor Mode
.954
Wiring Diagram .....................................................955
Diagnostic Procedure ...........................................957
MI & DATA LINK CONNECTORS ...........................958
Wiring Diagram .....................................................958
EVAPORATIVE EMISSION SYSTEM .....................962
Description ............................................................962
Component Inspection ..........................................965
POSITIVE CRANKCASE VENTILATION ...............967
Description ............................................................967
Component Inspection ..........................................967
AUTOMATIC SPEED CONTROL DEVICE (ASCD) .969
System Description ...............................................969
Component Description ........................................970
SERVICE DATA AND SPECIFICATIONS (SDS) ....971
Fuel Pressure .......................................................971
Idle Speed and Ignition Timing .............................971
Mass Air Flow Sensor ...........................................971
Intake Air Temperature Sensor .............................971
Engine Coolant Temperature Sensor ...................971
Heated Oxygen Sensor 1 Heater .........................971
Heated Oxygen sensor 2 Heater ..........................971
Crankshaft Position Sensor (POS) .......................971
Camshaft Position Sensor (PHASE) ....................972
Throttle Control Motor ...........................................972
Injector ..................................................................972
Fuel Pump ............................................................972
YD (WITH EURO-OBD)
INDEX FOR DTC .....................................................973
Alphabetical Index ................................................973
DTC No. Index ......................................................976
PRECAUTIONS .......................................................979
Precautions for Supplemental Restraint System
(SRS) “AIR BAG” and “SEAT BELT PRE-TEN-
SIONER” ...............................................................979
On Board Diagnostic (OBD) System of Engine ....979
Precautions ...........................................................979
Wiring Diagrams and Trouble Diagnosis ..............982
PREPARATION .......................................................983
Special Service Tools ...........................................983
Commercial Service Tools ....................................983
ENGINE CONTROL SYSTEM ................................984
System Diagram ...................................................984
Vacuum Hose Drawing .........................................985
System Chart ........................................................986
Fuel Injection Control System ...............................986
Fuel Injection Timing Control System ...................988
Air Conditioning Cut Control .................................988
Fuel Cut Control (At No Load & High Engine Speed) .988Crankcase Ventilation System ..............................989
CAN Communication ............................................989
BASIC SERVICE PROCEDURE .............................994
Fuel Filter ..............................................................994
Fuel Pump Learning Value Clearing .....................994
ON BOARD DIAGNOSTIC (OBD) SYSTEM ...........996
Introduction ...........................................................996
Three Trip Detection Logic and One Trip Detection
Logic .....................................................................996
Emission-related Diagnostic Information ..............996
NATS (Nissan Anti-theft System) .........................1001
Malfunction Indicator (MI) ....................................1001
OBD System Operation Chart ..............................1004
TROUBLE DIAGNOSIS .........................................1007
Trouble Diagnosis Introduction ............................1007
DTC Inspection Priority Chart ..............................1010
Basic Inspection ...................................................1012
Symptom Matrix Chart .........................................1016
Engine Control Component Parts Location ..........1020
Circuit Diagram ....................................................1025
ECM Harness Connector Terminal Layout ...........1027
ECM Terminals And Reference Value ..................1027
CONSULT-II Function (ENGINE) .........................1034
Generic Scan Tool (GST) Function ......................1040
CONSULT-II Reference Value in Data Monitor Mode
1042
Major Sensor Reference Graph in Data Monitor
Mode ....................................................................1043
TROUBLE DIAGNOSIS FOR INTERMITTENT INCI-
DENT ......................................................................1045
Description ...........................................................1045
Diagnostic Procedure ...........................................1045
POWER SUPPLY AND GROUND CIRCUIT ..........1046
Wiring Diagram ....................................................1046
Diagnostic Procedure ...........................................1047
Component Inspection .........................................1054
Ground Inspection ................................................1055
DTC U1000 CAN COMMUNICATION LINE ...........1056
Description ...........................................................1056
On Board Diagnosis Logic ...................................1056
DTC Confirmation Procedure ...............................1056
Wiring Diagram ....................................................1057
Diagnostic Procedure ...........................................1058
DTC P0016 CKP - CMP CORRELATION ..............1059
On Board Diagnosis Logic ...................................1059
DTC Confirmation Procedure ...............................1059
Diagnostic Procedure ...........................................1059
DTC P0045 TC BOOST CONTROL SOLENOID
VALVE .....................................................................1061
Description ...........................................................1061
On Board Diagnosis Logic ...................................1061
DTC Confirmation Procedure ...............................1061
Wiring Diagram ....................................................1062
Diagnostic Procedure ...........................................1063
Component Inspection .........................................1064
DTC P0088 FUEL SYSTEM ...................................1066
On Board Diagnosis Logic ...................................1066
DTC Confirmation Procedure ...............................1066