2005 NISSAN X-TRAIL oil level

CHASSIS AND BODY MAINTENANCE
MA-41
C
D
E
F
G
H
I
J
K
MA
B
MA

d. Remove A/T fluid level gauge and wipe clean lint-free paper.
CAUTION:
When wiping away the A/T fluid level gauge, always use lint-free paper, not cloth one.
e. Re-insert A/T fluid level gauge into charging pipe as far as it will go.
CAUTION:
To check fluid level, insert the A/T fluid level gauge until the cap contacts the end of the A/T fluid
charging pipe, with the A/T fluid level gauge reversed from the normal attachment conditions.
f. Remove A/T fluid level gauge and note reading. If reading is at low side of range, add fluid to the A/T fluid
charging pipe.
CAUTION:
Do not overfill.
4. Drive vehicle for approximately 5 minutes in urban areas.
5. Re-check fluid level at fluid temperatures of 50 to 80°C (122 to 176°F) using “HOT” range on A/T fluid
level gauge.
CAUTION:

When wiping away the A/T fluid level gauge, always use lint-free paper, not cloth one.

To check fluid level, insert the A/T fluid level gauge until the cap contacts the end of the A/T fluid
charging pipe, with the A/T fluid level gauge reversed from the normal attachment conditions.
6. Check fluid condition.

If fluid is very dark or smells burned, refer to AT section for
checking operation of A/T. Flush cooling system after repair of
A/T.

If A/T fluid contains frictional material (clutches, bands, etc.),
replace radiator and flush cooler line using cleaning solvent
and compressed air after repair of A/T. Refer to CO-12,
"RADIATOR" , CO-15, "RADIATOR (ALUMINUM TYPE)" .
7. Install the removed A/T fluid level gauge in the A/T fluid charging
pipe.
Changing A/T FluidELS000BW
1. Warm up A/T fluid.
2. Stop engine.
3. Drain A/T fluid from drain plug and refill with new A/T fluid.
Always refill same volume with drained fluid.
4. Run engine at idle speed for five minutes.
5. Check fluid level and condition. Refer to MA-40, "
Checking A/T Fluid" . If fluid is still dirty, repeat steps 2
through 5.
Checking Transfer OilELS000BT
Check for oil leakage and oil level.
(For details, refer to TF-10, "
Inspection" .)
SMA853B
Fluid grade:
Genuine NISSAN ATF or equivalent. Refer to
MA-17, "
RECOMMENDED FLUIDS AND LUBRI-
CANTS" .
Fluid capacity (With torque converter):
Approx. 8.5 (7-1/2 lmp qt)
Drain plug:
: 34 N·m (3.5 kg-m, 25 ft-lb)
SMA052D

MA-42
CHASSIS AND BODY MAINTENANCE

CAUTION:
Never start engine while checking oil level.
Changing Transfer OilELS000BU
1. Drain oil from drain plug and refill with new gear oil.
(For details, refer to TF-10, "
Replacement" .)
2. Check oil level.
CAUTION:
Carefully fill the oil. (Fill up for Approx. 3 minutes.)
Checking Propeller ShaftELS000BE
Check propeller shaft for damage, looseness or grease leakage.Filler plug:
: 14.7 N·m (1.5 kg-m, 11 in-lb)
SDIA0513E
Oil grade:
API GL-5
Viscosity:
Refer toMA-17, "
RECOMMENDED FLUIDS AND
LUBRICANTS"
Oil capacity:
: Approx. 0.31 (1/2 lmp pt)
Drain plug:
: 14.7 N·m (1.5 kg-m, 11 in-lb)
Filler plug:
: 14.7 N·m (1.5 kg-m, 11 in-lb)SDIA0512E
Tightening torque:
Refer to PR-3, "
REAR PROPELLER SHAFT" .
SMA118A

CHASSIS AND BODY MAINTENANCE
MA-43
C
D
E
F
G
H
I
J
K
MA
B
MA

Checking Differential Gear OilELS000BF
Check for oil leakage and oil level. (For details, refer to RFD-8,
"Checking Differential Gear Oil" .)
CAUTION:
Gaskets are not reusable. Never reuse them.
Changing Differential Gear OilELS000BG
1. Drain oil from drain plug and refill with new gear oil.
(For details, refer to RFD-8, "
Changing Differential Gear Oil" .)
2. Check oil level.
CAUTION:
Gaskets are not reusable. Never reuse them.
Balancing WheelsELS000BH
Adjust wheel balance using the road wheel center.
RotationELS000BI

After rotating the tires, adjust the tire pressure.

Retighten the wheel nuts when the vehicle has been driven for
1,000 km (600 miles) (also in cases of a flat tire, etc.).
CAUTION:
When installing wheels, tighten them diagonally by dividing
the work two to three times in order to prevent the wheels
from developing any distortion.Filler plug:
: 34.5 N·m (3.5 kg-m, 25 ft-lb)
SMA012C
Oil grad and Viscosity:
Refer to MA-17, "
RECOMMENDED FLU-
IDS AND LUBRICANTS" .
Capacity:
0.55 (1 lmp pt)
Drain plug:
: 34.5 N·m (3.5 kg-m, 25 ft-lb)
Filler plug:
: 34.5 N·m (3.5 kg-m, 25 ft-lb)
SDIA1151E
Wheel balance (Maximum allowable unbalance):
Refer to WT-6, "
SERVICE DATA AND SPECIFICATIONS (SDS)" .
Tightening torque of wheel nut:
98 - 117 N·m (10 - 12 kg·m, 73 - 86 ft·lb)
SMA829C

SERVICE DATA AND SPECIFICATIONS (SDS)
MA-49
C
D
E
F
G
H
I
J
K
MA
B
MA

SERVICE DATA AND SPECIFICATIONS (SDS)PFP:00030
Standard and LimitELS000K3
BELT DEFLECTION AND TENSION
QR20DE and QR25DE
YD22DDTi
*: When engine is cold.
RADIATOR
Unit: kPa (bar, kg/cm2 , psi)
ENGINE COOLANT CAPACITY
QR20DE and QR25DE
Unit: (lmp qt)
YD22DDTi
Unit: (lmp qt)
ENGINE OIL CAPACITY (APPROXIMATE)
QR20DE and QR25DE
Unit: (lmp qt)
YD22DDTi
Unit: (lmp qt)
SPARK PLUG
QR20DE and QR25DE
Unit: mm (in) Tensions of drive belts Auto-adjustment by auto-tensioner
Applied beltBelt deflection with 98 N (10 kg, 22 lb) force applied* mm (in)
New Adjusted Limit for re-adjusting
A/C compressor belt 4 - 5 (0.16 - 0.20) 6 - 7 (0.24 - 0.28) 8.5 (0.335)
Alternator and water pump belt 9.0 - 10.5 (0.354 - 0.413) 11.0 - 12.5 (0.433 - 0.492) 16.5 (0.650)
Cap relief pressureStandard 78 - 98 (0.78 - 0.98, 0.8 - 1.0, 11 - 14)
Limit 59 (0.59, 0.6, 9)
Leakage test pressure 157 (1.57, 1.6, 23)
Coolant capacity (With reservoir tank at “MAX” level) 7.1 (6-1/4)
Reservoir tank coolant capacity (At “MAX” level) 0.7 (5/8)
Coolant capacity (With reservoir tank at “MAX” level) 9.5 (8-3/8)
Reservoir tank coolant capacity (At “MAX” level) 0.7 (5/8)
Drain and refill With oil filter change 4.1 (3-5/8)
Without oil filter change 3.7 (3-1/4)
Dry engine (Overhaul)4.7 (4-1/8)
Drain and refill With oil filter change 5.2 (4-5/8)
Without oil filter change 4.9 (4-3/8)
Dry engine (Overhaul)6.3 (5-1/2)
Destination Except Russia For Russia
MakeNGK
Standard type LFR5A-11 PLFR5A-11
Hot type LFR4A-11 PLFR4A-11
Cold type LFR6A-11 PLFR6A-11
Spark plug gap Standard: 1.0 - 1.1 (0.039 - 0.043) Nominal: 1.1 (0.043)

IDX-3
A
C
D
E
F
G
H
I
J
K
L B
IDX
ALPHABETICAL INDEX
EC-1641
Basic inspection .. EC-79, EC-578, EC-1012, EC-1382
Battery ................................................................. SC-4
Baulk ring (M/T) .................................... MT-23, MT-41
Blower motor .... ATC-82, ATC-87, ATC-127, MTC-15,
MTC-18
, MTC-24
Blower resistor ................................................ MTC-25
Blower unit ....................... ATC-125, MTC-22, MTC-24
BOOST - Wiring diagram ............... EC-1153, EC-1508
Boring/horning cylinder block(QR20DE-QR25DE) .......
EM-111
Brake booster .................................................... BR-23
Brake fluid change ............................................... BR-8
Brake fluid level ................................................. MA-44
Brake fluid level and line check ........................... BR-8
Brake hydraulic line ........................................... BR-10
Brake inspection ................................................ MA-44
Brake lines and cables inspection ..................... MA-44
Brake master cylinder ........................................ BR-14
Brake pedal ......................................................... BR-6
Brake switch ..... EC-405, EC-809, EC-1313, EC-1664
BRK/SW - Wiring diagram EC-406, EC-811, EC-1314,
EC-1665
Bulb specifications ............................................ LT-152
Bumper, front ....................................................... EI-14
Bumper, rear ........................................................ EI-17
C
Camshaft inspection(QR20DE-QR25DE) .......... EM-58
Camshaft inspection(YD22DDTi) .................... EM-181
Camshaft position sensor (CMPS) EC-1169, EC-1175,
EC-1525
, EC-1531
Camshaft position sensor (PHASE) .. EC-257, EC-701
Camshaft(QR20DE-QR25DE) ........................... EM-56
Camshaft(YD22DDTi) ...................................... EM-180
CAN - Wiring diagram ....... EC-134, EC-634, EC-1057,
EC-1426
, LAN-12, LAN-28, LAN-44, LAN-69, LAN-87,
LAN-105
, LAN-131, LAN-144, LAN-157
CAN (Controller Area Network) ........ LAN-11, LAN-27,
LAN-43
, LAN-68, LAN-86, LAN-104, LAN-130,
LAN-143
, LAN-156
CAN communication EC-39, EC-133, EC-552, EC-633,
EC-989
, EC-1056, EC-1365, EC-1425, AT-32, AT-97,
AT-329
, TF-45, LAN-11, LAN-27, LAN-43, LAN-68,
LAN-86
, LAN-104, LAN-130, LAN-143, LAN-156
Canister-See EVAP canister ............. EC-525, EC-965
CHARGE - Wiring diagram .................... SC-14, SC-15
Charging system ................................................ SC-13
Chassis and body maintenance ........................ MA-39
CHIME - Wiring diagram ................ DI-54, DI-57, DI-58
CIGAR - Wiring diagram .................................. WW-29
Cigarette lighter ............................................... WW-29
Circuit breaker ................................................... PG-12
CKPS - Wiring diagram EC-1059, EC-1158, EC-1164,
EC-1428
, EC-1513, EC-1520
Clearance lamp ................................................ LT-116
Clock ................................................................... DI-63
CLOCK - Wiring diagram .................................... DI-63
Closed loop control .............................. EC-36, EC-549
Clutch cover ....................................................... CL-16
Clutch disc ......................................................... CL-16
Clutch master cylinder ......................................... CL-9
Clutch operating cylinder ................................... CL-12
Clutch pedal ......................................................... CL-5
Clutch release bearing ....................................... CL-14
Clutch release mechanism ................................ CL-14
Clutch withdrawal lever ...................................... CL-14
CMPS - Wiring diagram EC-1059, EC-1170, EC-1176,
EC-1428
, EC-1526, EC-1532
Coil spring (rear) ............................................... RSU-8
Collision diagnosis .......................................... SRS-48
Combination meter ............................................... DI-4
Combination switch ............................................. LT-96
Component Location (auto A/C) ......... ATC-35, MTC-4
Compression pressure(QR20DE-QR25DE) ..... EM-70
Compression pressure(YD22DDTi) ................ EM-209
Compressor clutch removal and installation .. ATC-146
Compressor special service tool ...................... ATC-14
Condenser ..................................................... ATC-155
Connecting rod bearing clearance(QR20DE-QR25DE)
EM-109
Connecting rod bearing clearance(YD22DDTi) EM-252
Connecting rod bushing clearance(YD22DDTi) EM-246
Connecting rod(QR20DE-QR25DE) ............... EM-109
Connecting rod(YD22DDTi) .............. EM-242, EM-248
CONSULT for engine ......................... EC-103, EC-604
CONSULT-II for engine ................. EC-1034, EC-1405
Control lever (M/T) ............................................. MT-16
Control unit ..................................... ATC-120, MTC-21
Control units (terminal arrangement) ................. PG-76
Controller Area Network (CAN) ........ LAN-11, LAN-27,
LAN-43
, LAN-68, LAN-86, LAN-104, LAN-130,
LAN-143
, LAN-156
Converter housing installation ......................... AT-523
COOL/F - Wiring diagram EC-356, EC-759, EC-1127,
EC-1483
Coolant replacement(QR20DE-QR25DE) ........ MA-20
Coolant replacement(YD22DDTi) ..................... MA-30
Cooling circuit (engine)(QR20DE-QR25DE) ....... CO-7
Cooling circuit (engine)(YD22DDTi) ................. CO-30
Cooling fan ............................................ CO-19, CO-37
Cooling fan relay EC-367, EC-770, EC-1137, EC-1492
Coupling sleeve (M/T) ........................... MT-23, MT-41
Cowl top .............................................................. EI-20
Cowl top cover .................................................... EI-20
Crankcase ventilation system .......... EC-989, EC-1365
Crankcase ventilation system - See Positive crankcase
ventilation ........................................... EC-527
, EC-967
Crankshaft position sensor (POS) ..... EC-250, EC-693
Crankshaft position sensor (TDC) EC-1157, EC-1163,
EC-1512
, EC-1518
Crankshaft(QR20DE-QR25DE) ........................ EM-90
Cylinder block boring(QR20DE-QR25DE) ...... EM-112
Cylinder block boring(YD22DDTi) ................... EM-250
Cylinder block(QR20DE-QR25DE) ................... EM-89
Cylinder block(YD22DDTi) .............................. EM-230
Cylinder head bolt tightening(QR20DE-QR25DE) ........

IDX-7
A
C
D
E
F
G
H
I
J
K
L B
IDX
ALPHABETICAL INDEX
P
Park/Neutral position switch ............. EC-398
, EC-802,
EC-1322
, EC-1673
Park/neutral position switch (A/T) .................... AT-100
Park/neutral position switch (M/T) ..................... MT-15
PCV (positive crankcase ventilation) . EC-527, EC-967
PGC/V - Wiring diagram .................................. EC-271
PHASE - Wiring diagram ................... EC-258, EC-703
Pilot bushing replacement - See Pilot
converter(QR20DE-QR25DE) ........................... EM-89
Piston assembly(QR20DE-QR25DE) .............. EM-111
Piston pin inspection(QR20DE-QR25DE) ....... EM-107
Piston pin inspection(YD22DDTi) .................... EM-242
Piston ring inspection(QR20DE-QR25DE) ...... EM-108
Piston ring inspection(YD22DDTi) ................... EM-247
Piston to bore clearance(QR20DE-QR25DE) . EM-111
Piston to bore clearance(YD22DDTi) .............. EM-250
PNP/SW - Wiring diagram EC-400, EC-804, EC-1323,
EC-1674
POS - Wiring diagram ........................ EC-251, EC-695
POWER - Wiring diagram .................................... PG-3
Power antenna .................................................. AV-37
Power door lock .................................................. BL-22
Power seat ......................................................... SE-10
Power socket ................................................... WW-31
Power steering fluid level ......................... PS-6, MA-45
Power steering gear .......................................... PS-16
Power steering oil pressure switch EC-1326, EC-1677
Power steering oil pump .................................... PS-27
Power steering pressure (PSP) sensor .......... EC-278,
EC-711
Power steering system bleeding .......................... PS-6
Power supply routing ........................................... PG-2
Power window .................................................. GW-40
Precations for Leak detection dye ................... ATC-12
Precautions (General) .......................................... GI-4
Pre-delivery inspection ........................................ MA-4
Pressure plate - See Clutch cover ..................... CL-16
PRGVLV - Wirng diagram ............................... EC-885
Propeller shaft ..................................................... PR-3
Propeller shaft on vehicle service ........................ PR-3
PS/SEN - Wiring diagram .................. EC-279, EC-712
PST/SW - Wiring diagram ............. EC-1327, EC-1678
Q
Quick-glow system ........................ EC-1305
, EC-1643
R
R/FOG - Wiring diagram ................................... LT-112
Radiator(QR20DE-QR25DE) ................ CO-12, CO-15
Radiator(YD22DDTi) ............................ CO-35, CO-39
Radio - See Audio ............................................... AV-4
Rear air spoiler .................................................... EI-30
Rear bumper ........................................................ EI-17
Rear disc brake ................................................. BR-32
Rear door ............................................................ BL-18
Rear fog lamp ................................................... LT-112
Rear panel finisher .............................................. EI-31
Rear seat ........................................................... SE-32
Rear seat belt ...................................................... SB-4
Rear side window ............................................. GW-13
Rear suspension ............................................... RSU-5
Rear washer .................................................... WW-14
Rear window defogger ...................................... GW-17
Rear wiper ....................................................... WW-14
Refrigerant connection precaution ..................... ATC-5
Refrigerant discharging evacuating charging ATC-141
Refrigerant general precaution .......................... ATC-5
Refrigerant lines ............................................. ATC-141
Refrigerant pressure sensor EC-474, EC-914, ATC-18,
ATC-94
, ATC-157
Refrigeration cycle ........................................... ATC-18
Release bearing (clutch) .................................... CL-14
Removal and installation (A/T) ......................... AT-413
Removal and installation (Transfer) ................... TF-57
Reverse idler shaft (M/T) ...................... MT-23, MT-41
Reverse lamp switch (M/T) - See Back-up lamp switch
(M/T) .................................................................. MT-15
Reverse main gear (M/T) ...................... MT-23, MT-41
Rocker cover(QR20DE-QR25DE) .................... EM-44
Rocker cover(YD22DDTi) ............................... EM-178
Room lamp ....................................................... LT-132
Room lamp - See Interior lamp ......................... LT-132
ROOM/L - Wiring diagram ................................ LT-132
RP/SEN - Wiring diagram .................. EC-475, EC-915
RRO2 - Wiring diagram ..................... EC-852, EC-868
S
S/LOCK - Wiring diagram ....................... BL-24
, BL-45
S/SIG - Wiring diagram .................. EC-1345, EC-1696
SCTC/V - Wiring diagram ............. EC-1232, EC-1265,
EC-1271
, EC-1276, EC-1281, EC-1571, EC-1604,
EC-1610
, EC-1615, EC-1620
SEAT - Wiring diagram ...................................... SE-11
Seat belt inspection .......................................... MA-47
Seat belt pre-tensioner disposal ..................... SRS-42
Seat belt, front ..................................................... SB-3
Seat belt, rear ...................................................... SB-4
Seat, front .......................................................... SE-24
Seat, rear ........................................................... SE-32
Self-diagnosis (Transfer) ................................... TF-32
SEN/PW - Wiring diagram ................. EC-373, EC-776
Sheft warning system ...................................... BL-104
SHIFT - Wiring diagram ................................... AT-399
Shift control components (M/T) ............. MT-25, MT-43
Shift fork (M/T) ...................................... MT-25, MT-43
Shift lever ........................................................... MT-16
Shift lock system .............................................. AT-398
Shift schedule .................................................. AT-530
Shift solenoid valve A (A/T) ............................. AT-128
Shift solenoid valve B (A/T) ............................. AT-128
Side air bag (satellite) sensor ......................... SRS-39
Side window - See Rear side window ............... GW-13
Spark plug replacement(QR20DE-QR25DE) ... MA-26