Page 423 of 788
COMBINATION METER ASSEMBLY
CHASSIS ELECTRICAL54A-35
STEP 5. Retest the system
Q: Is the speedometer normal?
YES : .
The procedure is complete. (If no
malfunctions are found in all steps, an
intermittent malfunction is suspected. Refer
to GROUP 00, How to Use
Troubleshooting/Inspection Service
Points-How to Cope with Intermittent
Malfunction P.00-5).
NO : . Replace the combination meter assembly.
STEP 6. Check whether the diagnosis code is
reset.
Q: Is the MPI-related diagnosis code set?
YES :
Refer to GROUP 13A − Troubleshooting
P.13A-15, GROUP 13B − Troubleshooting
P.13B-15.
NO : . Go to Step 7.
STEP 7. Connector check: Combination meter
connector C-04 and engine-ECU connector C-127
Q: Is combination meter connector C-04 and
engine-ECU connector C-127 in good condition?
YES : .
Go to Step 8.
NO : . Repair or replace the damage
component(s).
STEP 8. Check the wiring harness between
combination meter connector C-04 (terminal 11)
and engine-ECU connector C-125
vehicles>, C-127 (terminal
58).
AC303798
Connector: C-04
Harness side
AT
AC303814
Connector: C-04
Harness side
AT
AC303816BA
Connector: C-127
C-127 (Y)
Harness side
AC303798
Connector: C-04
Harness side
AT
AC303804
Connector: C-125
C-125 (Y)
Harness side
51 52 53 54 55 56 57 58
66 65 64 63 62 61 60 59
AT
Page 424 of 788
COMBINATION METER ASSEMBLY
CHASSIS ELECTRICAL54A-36
NOTE:
Prior to the wiring harness inspection, check
intermediate connectors C-14 (LH drive vehicles),
C-136 (RH drive vehicles), joint connectors C-12 (LH
drive vehicles), C-134 (RH drive vehicles) and repair
if necessary.
Q: Is the wiring harness between combination meter
connector C-04 (terminal 11) and engine-ECU
connector C-127 (terminal 58)
in good condition?
YES :
Go to Step 9.
NO : Repair the wiring harness.
STEP 9. Retest the system.
Q: Is the speedometer normal?
YES :
The procedure is complete. If no
malfunctions are found in all steps, an
intermittent malfunction is suspected (Refer
to GROUP 00, How to Use
Troubleshooting/Inspection Service
Points-How to Cope with Intermittent
Malfunction P.00-5).
NO : Go to Step 10.
STEP 10. Pulse check
Use the MUT-II/III or a voltmeter to check that the
vehicle speed signal is received.
OK: The MUT-II/III sounds or the voltmeter
needle fluctuates.
Q: Is the check result normal?
YES :
Replace the combination meter assembly.
NO : Replace the engine-ECU.
AC303814
Connector: C-04
Harness side
AT
AC303816AW
Connector: C-127
C-127 (Y)
Harness side
585261556256605459535751
AC303801
Connector: C-12, C-14
C-12C-14 (GR)
C-12
C-14 Harness side
AD
System switch Check conditions
Vehicle speed signal When the vehicle speed
has reached 10 km/h or
more
Page 427 of 788
COMBINATION METER ASSEMBLY
CHASSIS ELECTRICAL54A-39
STEP 3. Connector check: Combination meter
connector C-04 and diagnosis connector C-11
Q: Is combination meter connector C-04 and
diagnosis connector C-11 in good condition?
YES :
Go to Step 4.
NO : Repair or replace the damage
component(s).
STEP 4. Check the wiring harness between
combination meter connector C-04 (terminal 12)
and diagnosis connector C-11 (terminal 14).
NOTE:
Prior to the wiring harness inspection, joint connector
C-03 , and repair if necessary.
Q: Is the wiring harness between combination meter
connector C-04 (terminal 12) and diagnosis
connector C-11 (terminal 14) in good condition?
YES :
Go to Step 5.
NO : Repair or replace the wiring harness.
AC303798
Connector: C-04
Harness side
AT
AC303800
C-11 (B) Connector: C-11
Front side
AH
AC303814
Connector: C-04
Harness side
AT
AC303812
AD
Connector: C-11
Front side
C-11 (B)
AC303798AU
Connector: C-03, C-04
C-04
C-03 (B)
C-04 C-03 Harness side
AC303800
C-11 (B) Connector: C-11
Front side
AH
AC303814
Connector: C-04
Harness side
AT
AC303812
AD
Connector: C-11
Front side
C-11 (B)
Page 429 of 788
COMBINATION METER ASSEMBLY
CHASSIS ELECTRICAL54A-41
Q: Is combination meter connector C-04 and
engine-A/T-ECU connector C-124, C-126 in good
condition?YES :
Go to Step 8.
NO : Repair or replace the damage
component(s).
AC303814
Connector: C-04
Harness side
AT
AC303817
Connector: C-124, C-126
C-124
C-126
C-126 (GR)
C-124 (GR)
Harness side
41 42 43 44 45
57 56 55 54 53 52 51 50 49 48 47
58 59 60 61 62 63 64 65 6646
71 72 73 74 75 76 77
89 88 87 86 85 84 83 82 81 80 79 78
90 91 92 93 94 95 96 97 98
AM
Page 431 of 788
COMBINATION METER ASSEMBLY
CHASSIS ELECTRICAL54A-43
NOTE:
Prior to the wiring harness inspection, check
intermediate connectors C-14 (LH drive vehicles),
C-13 (LH drive vehicles), C-136 (RH drive vehicles),
C-137 (RH drive vehicles), joint connectors C-12 (LH
drive vehicles), C-134 (RH drive vehicles), C-03 (LH
drive vehicles) and repair if necessary.Q: Is the wiring harness between combination meter
connector C-04 (terminal 11, 12) and
engine-A/T-ECU connector C-124 (terminal 43, 80)
in good condition?
YES :
Go to Step 9.
NO : Repair the wiring harness.
STEP 9. Retest the system.
Q: Is the speedometer normal?
YES :
The procedure is complete. (If no
malfunctions are found in all steps, an
intermittent malfunction is suspected. Refer
to GROUP 00, How to Use
Troubleshooting/Inspection Service
Points-How to Cope with Intermittent
Malfunction P.00-5).
NO : Go to Step 10.
STEP 10. Pulse check
Use the MUT-II/III or a voltmeter to check that the
vehicle speed signal is received.
OK: The MUT-II/III sounds or the voltmeter
needle fluctuates.
Q: Is the check result normal?
YES :
Replace the combination meter assembly.
NO : Replace the engine-ECU.
AC303800
Connector: C-12
Harness side
AI
AC303819
Connectors: C-134, C-136, C-137
C-134
AE
C-134
C-136C-137
C-136 (GR)
C-137
System switch Check conditions
Vehicle speed signal When the vehicle speed
has reached 10 km/h or
more
Page 433 of 788
Page 435 of 788
Page 437 of 788
COMBINATION METER ASSEMBLY
CHASSIS ELECTRICAL54A-49
DIAGNOSIS PROCEDURE
STEP 1. Check the fuel gauge circuit.
(1) Disconnect D-13 fuel gauge unit connector.
(2) Connect a test lamp (12 V − 3.4 W) via test
harness (MB991219) between the wiring harness
connector terminals 1 and 2.
(3) Turn the ignition switch to the "ON" position.
Q: Does the test lamp illuminate?
YES :
Go to Step 4.
NO : . Go to Step 2.
STEP 2. Connector check: Combination meter
connector C-06, fuel gauge unit connector D-13
Q: Is combination meter connector C-04, fuel gauge
unit connector D-13 in good condition?
YES :
Go to Step 3.
NO : Repair or replace the damaged
component(s).
STEP 3. Check the wiring harness between
combination meter connector C-06 (terminal 51)
and fuel gauge unit connector D-13 (terminal 1).
AC305320
AB
Test lamp
(12 V - 3.4 W)
MB991219
Harness side
Fuel gauge
Earth
AC303798
Connector: C-04
Harness side
AT
AC303871
Connector: D-13
Harness sideD-13 (B)
AI
AC303917
D-13 (B) Connector: D-13
Harness side
AH
AC303798
Connector: C-06
Harness side
C-06 (L)
31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51
AV
AC303814AU
Connector: C-06
Harness side
31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51
C-06 (L)
