2005 MITSUBISHI LANCER air condition

DOOR MIRROR
EXTERIOR51-42
Step 7. Connector check: C-212 junction block
connector
Q: Is the check result normal?
YES :
Go to Step 8.
NO : Repair the defective connector.
Step 8. Check the wiring harness between E-11
door mirror assembly (RH) connector terminal
No.1 and C-212 junction block connector
terminal No.3.
•Check the power supply line for open circuit.NOTE:
Prior to the wiring harness inspection, check
intermediate connector C-112 , C-30
and repair if necessary.
Q: Is the check result normal?
YES :
Intermittent malfunction (Refer to GROUP
00 − How to Cope with Intermittent
Malfunction P.00-5).
NO : Repair the wiring harness.
Step 9. Connector check: E-02 door mirror
assembly (LH) connector
Q: Is the check result normal?
YES :
Go to Step 10.
NO : Repair the defective connector.
Step 10. Check the door mirror assembly (LH).
Check that the heater element of the door mirror
assembly (LH) is in good condition (Refer to
P.51-47).
Q: Is the check result normal?
YES : .
Go to Step 11.
NO : . Replace the door mirror assembly (LH).
AC304913
21716151718 201912345 623 222425282627981011141213
Connector: C-212
Harness side
AB
Junction block (Front view)
AC304817
Connector: E-11
Harness side
AB
AC304913
21716151718 201912345 623 222425282627981011141213
Connector: C-212
Harness side
AB
Junction block (Front view)
AC304819
Connector: C-112
AB
AC304818
Connector: E-02
Harness side
AB

IGNITION SWITCH
CHASSIS ELECTRICAL54A-11
DIAGNOSIS PROCEDURE
STEP 1. Check for presence of other key near the
key in the ignition.
Q: Is there any other key near the key in the ignition?
YES :
Move the other key well away from key
being used. Retest the system.
NO : Go to Step 2.
STEP 2. Check that the engine start using the
spare ignition key which encrypted code has
been registered.
Q: Does the engine start using the spare ignition key
for which the encrypted code has been registered?
YES :
Replace the ignition key that does not work.
Then register the password (secret code)
and encrypted code P.54A-20. Retest the
system.
NO : Go to Step 3.
STEP 3. Check whether the diagnosis code is
reset.
Q: Which diagnosis code is set, code No.11 or 12 the
encrypted code has been registered?
Code No.12 is set :
Refer toP.54A-11.
Code No.11 is set : Go to Step 4.
STEP 4. Connector check: Immobilizer-ECU
connector C-202-1.
Q: Are immobilizer-ECU connector C-202-1 in good
condition?
YES :
Replace immobilizer-ECU and Then
register the password (secret cod) and
encrypted code P.54A-20. Retest the
system.
NO : Repair or replace the damage
component(s).
Code No.12: Encrypted Codes are Not identical or not Registered
DIAGNOSIS CODE SET CONDITION
The encrypted code sent by the transponder is not
the same encrypted code which is registered in the
immobilizer-ECU.
NOTE: Diagnosis code No.12 is always set together
with MPI system diagnosis code No.P0513.
TROUBLESHOOTING HINTS
•The encrypted code in the ignition key has not
been properly registered.•Malfunction of immobilizer-ECU.
DIAGNOSIS PROCEDURE
Was the encrypted code registered?
YES :
Replace the immobilizer-ECU and then
re-register the encrypted code (Refer to
P.54A-20).
NO : Register the encrypted code (Refer to
P.54A-20).
SYMPTOM CHARTM1543007201075
AC303806
Connector: C-202-1
Harness side
AF
Symptom Inspection
procedure No.Reference page
Communication with MUT-II/III is impossible. 1
P.54A-12
The ignition key cannot be registered. 2
P.54A-18
Engine does not start (cranking but no initial combustion). 3
P.54A-18

IGNITION SWITCH
CHASSIS ELECTRICAL54A-13
TROUBLESHOOTING HINTS
•Malfunction of the immobilizer-ECU.
•Malfunction of the engine-ECU or
engine-A/T-ECU .
•The wiring harness or connectors may have
loose, corroded, or damaged terminals, or
terminals pushed back in the connector.
DIAGNOSIS PROCEDURE
STEP 1. Check if MUT-II/III can communicate with
the MPI system and if an MPI system diagnosis
code other than P0513 is set.
Q: Can MUT-II/III communicate with the MPI system?
Is an MPI system diagnosis code other than P0513
set?
YES :
Go to Step 2.
NO : Refer to GROUP 13A, MPI Diagnosis
P.13A-15, GROUP 13B, MPI Diagnosis
P.13B-15.
STEP 2. Voltage measurement at
immobilizer-ECU connector C-202-1.
(1) Disconnect immobilizer-ECU connector C-202-1.
(2) Turn the ignition switch to the "ON" position.
(3) Measure the voltage between terminal 1 and
earth.
OK: System voltage
Q: Is the check result normal?
YES :
Go to Step 5.
NO : Go to Step 3.
STEP 3. Connector check: Immobilizer-ECU
connector C-202-1 and engine control relay
connector B-16X
Q: Are immobilizer-ECU connector C-202-1 and
engine control relay connector B-16X in good
condition?
YES :
Go to Step 4.
NO : Repair or replace the damaged
component(s). Confirm that MUT-II/III
communicates normally.AC303806
Connector: C-202-1
Harness side
AF
AC304844AB
Connector C-202-1
(Harness side)
AC303806
Connector: C-202-1
Harness side
AF
AC303796
Connector: B-16X
Harness side
AF

IGNITION SWITCH
CHASSIS ELECTRICAL54A-14
STEP 4. Check the harness wires between
immobilizer-ECU connector C-202-1 (terminal 1)
and engine control relay connector B-16X
(terminal 4).
NOTE:
Prior to the wiring harness inspection, check
intermediate connector C-13 ,
C-137 , joint connector C-12
, C-134 and
key reminder switch connector C-202, and repair if
necessary.
Q: Are the harness wires between immobilizer-ECU
connector C-202-1 (terminal 1) and engine control
relay connector B-16X (terminal 4) in good
condition?
YES :
There is no action to be taken.
NO : Replace damaged component(s). Confirm
that MUT-II/III communicates normally.
AC303806
Connector: C-202-1
Harness side
AF
AC303796
Connector: B-16X
Harness side
AF
AC303801
Connector: C-12, C-13
C-12
C-13
C-12
C-13
AC
AC303819
Connector: C-134, C-137
C-134
C-137
C-134
C-137
AC
AC303806
Connector: C-202
Harness side
AG

IGNITION SWITCH
CHASSIS ELECTRICAL54A-15
STEP 5. Resistance measurement at
immobilizer-ECU connector C-202-1.
(1) Disconnect immobilizer-ECU connector C-202-1.
(2) Measure the resistance between terminal 4 and
earth.
OK: 2 ohms or less
Q: Is the check result normal?
YES :
Go to Step 8.
NO : Go to Step 6.
STEP 6. Connector check: immobilizer-ECU
connector C-202-1
Q: Is immobilizer-ECU connector C-202-1 in good
condition?
YES :
Go to Step 7.
NO : Repair or replace the damaged
component(s). Confirm that MUT-II/III
communicates normally.
STEP 7. Check the harness wire between
immobilizer-ECU connector C-202-1 (terminal 4)
and earth.
NOTE:
Prior to the wiring harness inspection, check joint
connector C-104 , C-07 drive vehicles>, key reminder switch connector
C-202, and repair if necessary.
AC303806
Connector: C-202-1
Harness side
AF
AC304851AB
Connector 202-1
(Harness side)
AC303806
Connector: C-202-1
Harness side
AF
AC303806
Connector: C-202-1
Harness side
AF
AC303814
Connector: C-07

C-07(GR)
Harness side
AL
AC303804AO
Harness connector: C-104

C-104(GR)
Harness side
AC303806
Connector: C-202
Harness side
AG

IGNITION SWITCH
CHASSIS ELECTRICAL54A-16
Q: Is the harness wire between immobilizer-ECU
connector C-202-1 (terminal 4) and earth in good
condition?
YES :
There is no action to be taken.
NO : Repair or replace the damaged
component(s). Confirm that MUT-II/III
communicates normally.
STEP 8. Connector check: immobilizer-ECU
connector C-202-1 and engine-ECU connector
C-127 or engine-A/T-ECU connector C-128

Q: Are immobilizer-ECU connector C-202-1 and
engine-ECU connector C-127 or
engine-A/T-ECU connector C-128 in good
condition?
YES :
Go to Step 9.
NO : Repair or replace the damaged
component(s). Confirm that MUT-II/III
communicates normally.
STEP 9. Check the harness wires between
immobilizer-ECU connector C-202-1 (terminal 3)
and engine-ECU connector C-127 (terminal 51)
or engine-A/T-ECU connector C-128
(terminal 111) .
AC303805
Connector: C-127 , C-128
C-128 (GR)
C-127 (Y)
C-127
C-128
585261556256605459535751
101 102
103 104 105 106 107
120 119 118 117 116 115 114 113 112 111 110 109 108
121 122 123 124 125 126 127 128 129 130
Harness side
AJ
AC303806
Connector: C-202-1
Harness side
AF
AC303805
Connector: C-127 , C-128
C-128 (GR)
C-127 (Y)
C-127
C-128
585261556256605459535751
101 102
103 104 105 106 107
120 119 118 117 116 115 114 113 112 111 110 109 108
121 122 123 124 125 126 127 128 129 130
Harness side
AJ
AC303806
Connector: C-202-1
Harness side
AF

IGNITION SWITCH
CHASSIS ELECTRICAL54A-17
NOTE:
Prior to the wiring harness inspection, check key
reminder switch connector C-202, intermediate
connector C-13 , C-137 drive vehicles>, and repair if necessary.Q: Are the harness wires between immobilizer-ECU
connector C-202-1 (terminal 3) and engine-ECU
connector C-127 (terminal 51) or
engine-A/T-ECU connector C-128 (terminal 111)
in good condition?
YES :
Go to Step 10.
NO : Repair or replace the damaged
component(s). Confirm that MUT-II/III
communicates normally.
STEP 10. Replace the immobilizer-ECU or
engine-ECU or engine-A/T-ECU .
Replace the immobilizer-ECU.
Q: Did the communication with MUT-II/III become
possible after replacing the immobilizer-ECU?
YES :
Register the password (secret code) and
encrypted code P.54A-20. Confirm that
MUT-II/III communicates normally
NO : Go to Step 11.
STEP 11. Recheck for malfunction.
Q: Is a malfunction eliminated?
YES :
The procedure is complete. If no
malfunctions are found in all steps, an
intermittent malfunction is suspected (Refer
to GROUP 00, How to Use
Troubleshooting/Inspection Service Points −
How to Cope with Intermittent Malfunction
P.00-5).
NO : Replace the engine-ECU or
engine-A/T-ECU .
AC303800
Connector: C-13

Harness side
AG
AC303818
AM
Connector: C-137

Harness side
AC303806
Connector: C-202
Harness side
AG

COMBINATION METER ASSEMBLY
CHASSIS ELECTRICAL54A-34
STEP 3. Connector check: Combination meter
connector C-04 and diagnosis connector C-11.
Q: Is combination meter connector C-04 and
diagnosis connector C-11 in good condition?
YES :
Go to Step 4.
NO : Repair or replace the damage
component(s).
STEP 4. Check the wiring harness between
combination meter connector C-04 (terminal 12)
and diagnosis connector C-11 (terminal 14).
NOTE:
Prior to the wiring harness inspection, joint connector
C-03 , and repair if necessary.
Q: Is the wiring harness between combination meter
connector C-04 (terminal 12) and diagnosis
connector C-11 (terminal 14) in good condition?
YES :
Go to Step 5.
NO : Repair or replace the wiring harness.
AC303798
Connector: C-04

Harness side
AT
AC303800
C-11 (B) Connector: C-11

Front side
AK
AC303814
Connector: C-04

Harness side
AT
AC303812
AD
Connector: C-11

Front side
C-11 (B)
AC303798AU
Connector: C-03, C-04
C-04
C-03 (B)
C-04 C-03 Harness side
AC303800
C-11 (B) Connector: C-11

Front side
AK
AC303814
Connector: C-04

Harness side
AT
AC303812
AD
Connector: C-11

Front side
C-11 (B)