2005 MITSUBISHI LANCER lock

IGNITION SWITCH
CHASSIS ELECTRICAL54A-26
5. Enter the vehicles password (secret code) on the
"Transponder ID addition" screen, and then click
the check mark icon.
6. If an additional registration is made successfully,
the screen will ask if another key is registered or
not. If the third ignition key is registered, remove
the key, which has been registered. Then insert
the third key within five seconds, and then turn it
to the ON position.
7. Register the additional ignition key according to
step 6 above. The number of the registered
ignition keys are shown on "The number of
registered key" screen.
NOTE: A maximum of eight different keys can be
registered.
8. This completes the registration operation. Turn
the ignition switch "LOCK" (OFF) and leave it off
for approximately ten seconds.
9. Check that the engine can be started with each of
the ignition keys.
10.Check that the immobilizer system diagnosis
code and MPI system diagnosis code did not set.
11.If not diagnosis code is shown, terminate the
MUT-III.
12.Turn the ignition switch to "LOCK" (OFF) position.
13.Disconnect MUT-III.Registration of additional key(s) without
using the MUT-III
If the MUT-III is not available, new key(s) can be
registered by operating two keys which have been
registered to the vehicle (A maximum of eight keys
can be registered to one vehicle). Follow the
procedure below to register new key(s) to the
vehicle.
NOTE: The registered key is the key that allows you
to start the engine.
1. Turn "ON" the ignition switch by using the first
registered key (key A), and wait for five seconds.
2. Remove the first registered key (key A).
3. Insert the second registered ignition key (key B),
and turn it to the ON position.
4. The immobilizer-ECU identifies the new key to
accept or reject it, and operates the immobilizer
indicator (See the table below).
5. If a new ignition key is registered further, repeat
steps 1 to 7 above.
A maximum of eight ignition keys can be registered
to one vehicle (If you attempt to register the ninth
key, the immobilizer-ECU rejects the key). If any of
the following conditions are satisfied, the additional
key registration mode will terminate:
•The ignition switch has been on for more than 30
seconds.
•After the ignition key has been turned to the
"LOCK" (OFF), the engine control relay is turned
off.
•The MUT-III has started communicating with
vehicle systems.
6. After the registration mode has terminated, the
additionally registered key(s) should allow you to
start the engine.
AC207301
AC209775POWERTRAIN IMMOBILIZER
Key ID registerey ID registerThe number of registered keyThe number of registered key3
Progre
Progre
Special FunctionTrasponder ID addition
About Additional TAbout Additional TransponderransponderID SETID SETIf register another key ID, press theIf register another key ID, press theOK button after inserting a new keyOK button after inserting a new keywithin 5 sec and turning on IG-SWwithin 5 sec and turning on IG-SW.

IGNITION SWITCH
CHASSIS ELECTRICAL54A-27
IGNITION SWITCH
REMOVAL AND INSTALLATIONM1543002100434
WARNING
•Before removal of the air bag module, refer to GROUP 52B, SRS Service Precautions and
Air Bag Module and Clock Spring P.52B-5.
•When removing and installing the steering wheel, do not let it bump against the air bag
module.
AC304659
2
3
4
67
15
AB
8
Removal steps
1. Column cover lower
2. Column cover upper
3. Steering wheel and air bag module
assembly (Refer to GROUP 37,
Steering wheel P.37-17 or P.37-19)
4. Clock spring and column switch
assembly (Refer to GROUP 37,
Steering shaft P.37-21)
<>5. Steering lock cylinder•Ignition switch connector
6. Ignition switch
7. Immobilizer-ECU
•Key reminder switch connector
8. Key reminder switch and bulb
assembly Removal steps (Continued)

IGNITION SWITCH
CHASSIS ELECTRICAL54A-28
REMOVAL SERVICE POINT
<> STEERING LOCK CYLINDER
REMOVAL
1. Insert the key in the steering lock cylinder and turn
it to the "ACC" position.
2. Using a small Phillips head screwdriver, pull the
steering lock cylinder toward you.
INSPECTIONM1544009700203
IGNITION SWITCH CONTINUITY CHECK
Disconnect ignition switch connector C-201 without
removing the ignition switch. Then check the
continuity.
KEY REMINDER SWITCH CONTINUITY
CHECK
Disconnect key reminder switch connector C-202
without removing the ignition switch and key
reminder switch. Then check the continuity.
AC304831AB
Locking pin
AC304833AB
Switch
position Tester
connectionSpecified
condition
"LOCK" (OFF) 1 − 2, 1 − 3,
1 − 4, 1− 5,
1 − 6, 2 − 3,
2 − 4, 2− 5,
2 − 6, 3 − 4,
3 − 5, 3 − 6,
4 − 5, 4 − 6,
5 − 6Open circuit
"ACC" 1 − 6 Less than 2
ohms
"ON" 1 − 2, 1 − 4,
1 − 6, 2 − 4,
2 − 6, 4 − 6Less than 2
ohms
"START" 1 − 2, 1 − 5,
2 − 5Less than 2
ohms
Status of
ignition keyTester
connectionSpecified
condition
Removed 4 − 6 Less than 2
ohms
Inserted 4 − 6 Open circuit
AC304834AB

COMBINATION METER ASSEMBLY
CHASSIS ELECTRICAL54A-58
STEP 6. Check the wiring harness between
combination meter connector C-04 (terminal 9)
and ignition switch (IG1).
NOTE: Prior to the wiring harness inspection, check
Junction block connectors C-210 and C-212, joint
connector C-03 , and repair if
necessary.
Q: Are the wiring harness between combination meter
connector C-04 (terminal 42) and ignition switch
(IG1) in good condition?
YES :
There is no action to be taken.
NO : Repair or replace the wiring harness. Check
to see that all meters operate.
AC303798AU
Connector: C-03, C-04
C-04
C-03 (B)
C-04 C-03 Harness side
AC303814
Connector: C-04

Harness side
AT
AC303809
Connector: C-210, C-212

C-212
C-210
C-210 Harness side
C-212
AX
Front view
AC303823
Connector: C-210, C-212

C-210
C-212Front view
Harness side
C-210
C-212
AU

ROOM LAMP
CHASSIS ELECTRICAL54A-78
INSTALLATION SERVICE POINTClamp the thumb on the fender panel the assemble
the side turn signal lamp.
ROOM LAMP
TROUBLESHOOTINGM1542000701311
Dimmer interior lamp control function
The room lamp off is delayed by ETACS-ECU. The
lamps off delay time vary according to the conditions.
The control details are as follows. The lamp delay off
Yes/NO and delay time can be set with the settings
(adjustment function). for adjustment methods and
adjustment details (post-adjustment operations).
•ADJUSTMENT PROCEDURE
•Not using SWS monitor: GROUP 54B,
P.54B-423.
•The room lamp lights up if the ignition switch is at
the "LOCK" (OFF) position and either of the
doors are opened (either of the door switches:
ON). At this time, if all doors are closed (all door
switches: OFF) then the lamp will gradually dim
down to lamps off in about 15 seconds.
NOTE: When the lamps are dimmed and the ignition
switch is turned ON or if the door is locked, then
the dimming operations stop and the lamps are
turned OFF.
•When the ignition switch is at the ON position and
one of the doors are opened (one of the door
switches: ON) then the room lamp will light up. At
this time, if all doors are closed (all door switches:
OFF) then the lamps will dim out.
•When the ignition key is pulled out the room lamp
lights up and then will dim out in 15 seconds. The
lamp will dim out if the ignition key is inserted
again and the door is locked while the timer is
activated.
The room lamp is controlled by the Smart Wiring
System (SWS). For troubleshooting, refer to
respective Groups below.•Not using SWS monitor: GROUP 54B, SWS
Troubleshooting P.54B-38.
•Using SWS monitor: GROUP 54C, SWS
Troubleshooting P.54C-22.
Interior lamp automatic shutdown
function system>
The interior lamp automatic shutdown function, dims
out the room lamp and other interior lamps by
activating the keep relay built-in the ETACS-ECU
when the ignition switch is OFF and the
multi-purpose fuse loaded signals built-in the
ETACS-ECU is ON and 30 minutes passes. The
lamps lights back up if the ignition switch is turned to
the ON position or either of the doors is opened
(either of the door switches: ON). The function
Yes/No feature can be changed with the settings
(adjustment function). for adjustment methods and
adjustment details (post-adjustment operations).
•ADJUSTMENT PROCEDURE
•Not using SWS monitor: GROUP 54B,
P.54B-423.
The head lamp are controlled by the Smart Wiring
System (SWS). For troubleshooting, refer to
respective Groups below.
•Not using SWS monitor: GROUP 54B, SWS
Troubleshooting P.54B-38.
•Using SWS monitor: GROUP 54C, SWS
Troubleshooting P.54C-22.
AC005719
Fender panelHook
Claw
Fender panel
: Front of vehicle
AE

CLOCK
CHASSIS ELECTRICAL54A-90
CLOCK
SPECIAL TOOLM1543000601663
CLOCK
REMOVAL AND INSTALLATION
M1543005900224
Tool Number Name Use
MB990784 Ornament remover Removal of centre panel and
centre air outlet panel
MB990784
AC304720AB
3
4
25
1
Removal steps
1. Knob
2. Centre panel
3. Meter bezel4. Centre air outlet panel
5. ClockRemoval steps (Continued)

55-1
GROUP 55
HEATER, AIR
CONDITIONER AND
VENTILATION
CONTENTS
SERVICE SPECIFICATIONS . . . . . . .55-3
LUBRICANTS . . . . . . . . . . . . . . . . . .55-3
SPECIAL TOOLS . . . . . . . . . . . . . . . .55-4
TROUBLESHOOTING . . . . . . . . . . . .55-5DIAGNOSIS TROUBLESHOOTING
FLOW . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 55-5
SYMPTOM CHART . . . . . . . . . . . . . . . . . . . 55-5
SYMPTOM PROCEDURES . . . . . . . . . . . . 55-5
CHECK AT ECU TERMINAL . . . . 55-67
CHECK AT ECU TERMINAL . . . . 55-68
Continued on next page
W ARNING S RE GA RDING S E RV ICIN G O F SUP P LE MEN TAL R ES TRAI NT S Y ST EM (SRS ) E Q UIP PE D VE HICL ES
I mp roper se rvi ce o r m ai nte na nce of a ny c omp onent of the SRS , or an y SRS -re la te d c om pone nt, ca n le a d to
personal injury or death to service personnel (from inadvertent firing of the air bag) or to the driver (from
re nd er ing the S RS inop er ati ve).
S e rvic e or m ai nten anc e of an y SRS com pon ent or SRS -re late d com pone nt m ust be pe rfor me d only a t an
authorized MITSUBISHI dealer.
M ITSUBISHI dealer p erso nnel must thoroughly review th is man ual, and esp ecially its GROU P 52B - Su pplemen tal
Restraint System (SR S) b efore beginn ing an y service o r maintenance of any comp onent of th e SRS or any SRS-
rel ated com ponent.
NOTE
The SRS includes the following components: front impact sens ors , SRS-ECU, SRS warning lamp, air bag module, c lock spring
and interconnecting wiring. Other SRS-related components (that may have to be remov ed/installed in connection with SRS
service or maintenance) are indicated in the table of c ontents by an asterisk (*).

TROUBLESHOOTING
HEATER, AIR CONDITIONER AND VENTILATION55-8
STEP 4. Check the wiring harness between C-107
outside/inside air selection damper control motor
connector terminal No.7 and the ignition switch
(IG2).
NOTE:
AC303804
Connector: C-107

AD
Harness side
AC303816
Connector: C-107
AI

Harness side
AC303798
Connector: C-35

AJ
2 1313 12 1421 105 4616 15 17789
19 18 2011
22
C-35 (L)
AC303814
Connector: C-35

AI
C-35(L)
AC303804
Connector: C-106

AC
C-106
AC303816
Connector: C-106
AH

AC303809
Connectors: C-209, C-210
AF
C-209
C-210
Junction block (front view)
C-209
Harness side
1016
145
12134117 238 9
C-210
Harness side
4 65321