2005 MITSUBISHI LANCER EVOLUTION IX torque

64G6 – TIGHTENING TORQUE
PartTightening Torque
Air pipe assembly bolt (eye bolt) 49 ± 5
Air pipe assembly bolt (M6 flange) 11 ± 1
Air pipe assembly bolt (M8 flange) 24 ± 3
Air pipe assembly bolt (M8 washer) 14 ± 1
Air control valve assembly bolt 22 ± 4
Engine hanger bolt 19 ± 3
Intake air temperature sensor 14 ± 1
Boost sensor bolt 5.0 ± 1.0
Intake manifold stay bolt 31 ± 3
Intake manifold bolt (M8) 20 ± 2
Intake manifold bolt nut (M10) 36 ± 6
Exhaust manifold
Engine hanger bolt 22 ± 3
Turbocharger heat protector bolt 23 ± 3
Oxygen sensor 44 ± 5
Exhaust fitting bracket bolt 35 ± 6
Exhaust filling bolt nut 59 ± 5
Air outlet fitting bolt 19 ± 1
Oil return pipe bolt (flange) 14 ± 1
Oil return pipe bolt (washer) 9.0 ± 1.0
Turbocharger assembly and pipe assembly bolt, nut 64 ± 5
Oil pipe bolt (M10 eye bolt) 17 ± 2
Oil pipe bolt (M12 eye bolt) 31 ± 2
Oil pipe bolt (M12 flange) 11 ± 1
Water pipe bolt (flange) 10 ± 1
Water pipe bolt (eye bolt) 42 ± 7
Exhaust manifold nut (M8) 33 ± 6
Exhaust manifold nut (M10) 55 ± 10
Water pump / Water hose
Coolant temperature sensor 29 ± 10
Coolant temperature gauge unit 11 ± 1
Water outlet fitting bolt 10 ± 1
Thermostat housing bolt 23 ± 4
Water inlet pipe bolt (M6) 10 ± 1
Water inlet pipe bolt (M8) 13 ± 2
Water pump bolt 14 ± 1
Knock sensor 23 ± 2
Rocker arm / Camshaft
Cam position sensor bolt 11 ± 1
Cover bolt 10 ± 2
Cam position sensing cylinder bolt 22 ± 4
Cam position sensor support bolt 14 ± 1
Bearing cap bolt 20 ± 1
Oil delivery body bolt 11 ± 1

74G6 - TIGHTENING TORQUES
Par tTightening Torque
Oil control pump11 ± 1
Check valve30 ± 3
Eye bolt42 ± 2
Oil pipe11 ± 1
Oil pipe joint30 ± 3
Oil pump / Sump
Drain plug39 ± 5
Sump bolt9.0 ± 3.0
Oil screen bolt19 ± 3
Baffle plate bolt22 ± 4
Oil pressure switch10 ± 2
Oil cooler bypass valve54 ± 5
Relief plug44 ± 5
Oil filter bracket bolt19 ± 3
Plug cap23 ± 3
Flange bolt36 ± 3
Front case bolt23 ± 3
Oil pump cover bolt17 ± 2
Oil pump cover screw10 ± 2
Piston / Connecting rod
Connecting rod cap nut20 ± 2 _ +90° ~94°
Crankshaft / Cylinder block
Flywheel bolt132 ± 5
Rear plate bolt11 ± 1
Bell housing cover bolt (flange)10 ± 2
Bell housing cover bolt (washer)9.0 ± 1.0
Rear oil seal case bolt11 ± 1
Beam bearing cap bolt25 ± 2 _ +90° ~ 100°
Check valve32 ± 2
Turbocharger
Waste gate actuator bolt12 ± 1
Sealants
Par tSpecified Sealant
Cam position sensor support *MZ100191 or equivalent
Note : * indicates point where liquid gasket (FIPG) used

124G6 – TIMING BELT
3. Push the V.V.T. sprocket firmly to the end and, holding the
hexagonal part of the camshaft with a wrench, check that the V.V.T.
sprocket does not rotate.
4. Hold the hexagonal section of the camshaft with a wrench and
tighten the V.V.T. sprocket bolt to the specified torque of 65 ±5 N-m.
5. Hold the hexagonal section of the camshaft with a wrench and
check that the V.V.T. sprocket does not rotate.
Note :
This check shows that the V.V.T. sprocket is locked at the maximum
delay angle by the interior pin.
Installation of plug cap
Note :
The washer must not be reused.
1. Install the washer on the plug cap.
2. Hold the hexagonal section of the camshaft with a wrench and
tighten the plug cap to the specified torque of 32±2 N-m.
B
*

194G6 – ROCKER ARM / CAMSHAFT
Installation Service Point
Installation of OCV filter
Note :
Before fitting the filter, check that it is clean and is not damaged
or deformed in any way.
Installation of eye bolt
Note :
The oil pump may be damaged if the oil pipe joint turns with the
eye bolt when it is fitted.
Hold the oil pipe joint in place with a spanner, etc., and then tighten
the eye bolt to the specified torque 42 ±2 N-m.
Installation of cam position sensor
support
1. Wipe away all traces of the old liquid gasket left on the cam
position sensor support and the cylinder head.
2. Apply a 3 mm-thick coat of the liquid gasket to the parts of the
cam position sensor support indicated on the diagram.
Liquid Gasket
Product name : MZ100191 or equivalent
Installation of cam position sensing
cylinder
1. Set the camshaft to the top dead centre for No.1.
2. Install the various vanes of the cam position sensing cylinder at
the positions indicated on the diagram.
Installation of cover / gasket
1. Before installing the cover and gasket, put the camshaft to the
No.1 top dead centre position, and check that the vanes of the
respective sensing cylinders are located in the positions shown in
the diagram.
Eye bolt
Hold with
spanner, etc.
Oil pipe joint
Exhaust sideIntake side
Exhaust side
Exhaust sideIntake side
Intake sideVane
Vane
Vane
Vane VaneVane
Vane Vane
Vane
(large) Vane
(large) Vane
(small)
Vane
(small)
A
*
B

*
C


*
D


*
E


*

204G6 – ROCKER ARM / CAMSHAFT
2. Ensure that the cutaways in the intake side cover and the tabs on the
gasket are aligned with the positions shown in the diagram, and
tighten at the specified torque of 14 ±1 N-m. The exhaust side cover
and gasket do not have a specified installation direction.
Comment :
The cover and gasket do not have distinct front and rear sides.
No cutawayNo installation direction Exhaust side
Intake side
Ta b Ta b
Cutaway
Cutaway

*

*


A


*


*


*


*


*


*



*

*