2005 LEXUS LS430 Owners Manual

INTERIOR EQUIPMENT
11 8
14L061b
On the instrument panel (Vehicles without navigation
system)
This display shows the outside temperature when the
ignition switch is on.
The displayed temperature ranges from –30 C (–22F) up to
50 C (122 F). If the temperature does not appear on the
display or it shows “ − − −”, take your vehicle to your Lexus
dealer.
14L237
 Multiinformation display
When you push the “DISP2” switch with the ignition switch on,
another outside temperature display appears on the
multi−information display. (For details, see “Multi −information
display” on page 90.)
The displayed temperature ranges from –30 C (–22F) up to
50 C (122 F). If the temperature does not appear on the
display or it shows “− − ”, take your vehicle to your Lexus dealer.

INTERIOR EQUIPMENT
11 9
CIGARETTE LIGHTER ANDASHTRAY
14L239
Front cigarette lighter and ashtray (for some models)
14L213
Rear cigarette lighter and ashtray Open
the ashtray cover. To use the cigarette lighter, press
in the cigarette lighter. After it finishes heating up, it
automatically pops out ready for use.
Do not hold the cigarette lighter pressed in.
If the engine is not running, the ignition switch must be in the
“ACC” position to use the lighter.
When finished with your cigarette, thoroughly extinguish it in
the ashtray to prevent other cigarette butts from catching fire.
After using the ashtray, push it back in or close the lid
completely.
To remove the ashtray, raise the lid and pull it out.
Use a Lexus genuine cigarette lighter or equivalent for
replacement.
CAUTION
To reduce the chance of injury in case of an accident or
sudden stop while driving, always close the ashtray
completely after use.

INTERIOR EQUIPMENT
120
POWER OUTLETS
14L062
In the rear console box
14L233
On the right side of the selector lever (for some models) The power outlets are designed for power supply for car
accessories.
The ignition switch must be in the “ACC” or “ON” position fo\
r
the power outlets to be used.
NOTICE

To prevent the fuse from being blown, do not use the
electricity over the total vehicle capacity of 10A/12V.
 To prevent the battery from being discharged, do not
use the power outlets longer than necessary when
the engine is not running.
 Close the power outlet lids when the power outlets
are not in use. Inserting anything other than an
appropriate plug that fits the outlet, or allowing any
liquid to get into the outlet may cause electrical
failure or short circuits.

INTERIOR EQUIPMENT
121
REAR CONSOLE BOX
14L064b
 1For the lower box 2For the upper tray
To use the rear console box, open as shown in the
illustration.
14L214
Sliding a tray will make an accommodating space larger.
14L215
To return the tray to its original position, slide it while pushing
either lever as shown.
The rear console box light for the lower box will come on with
the headlights on.
CAUTION
To reduce the chance of injury in case of an accident or
a sudden stop, always keep the console box lid closed
while driving.

INTERIOR EQUIPMENT
122
GLOVE BOX
14L240
 1Type A 2Type B 3Unlock 4Lock 5Open
To open the glove box door, pull the lever. To lock the
glove box door, insert the master key and turn it
clockwise.
With the tail lights on, the glove box light will come on when the
glove box door is open.
CAUTION
To reduce the chance of injury in case of an accident or
a sudden stop, always keep the glove box door closed
while driving.
GARAGE DOOR OPENER
The garage door opener (\b Universal
Transceiver) is manufactured under license from
HomeLink
\b and can be programmed to operate garage
doors, gates, entry doors, door locks, home lighting
systems, and security systems, etc.
(a) Programming the HomeLink\b
14L070
 1 Buttons 2Indicator light
The HomeLink
\b in your vehicle has 3 buttons and you can
store one program for each button.
To ensure correct programming into the HomeLink
\b, install a
new battery in the hand −held transmitter prior to programming.

INTERIOR EQUIPMENT
123
The battery side of the hand
−held transmitter must be pointed
away from the HomeLink
\b during the programming process.
For Canadian users, follow the procedure in “Programming an
entrance gate/Programming all devices in the Canadian
market”.
1. Decide which of 3 HomeLink
\b buttons you want to program.
2. Place your hand− held garage transmitter 25 to 75 mm (1 to
3 in.) away from the surface of the HomeLink
\b.
Keep the indicator light on the HomeLink
\b in view while
programming.
3. Simultaneously press and hold the hand −held garage
transmitter button along with the selected HomeLink
\b button.
4. When the indicator light on the HomeLink
\b changes from a
slow to a rapid flash after 20 seconds, you can release both
buttons.
5. Test the operation of the HomeLink
\b by pressing the newly
programmed button. If programming a garage door opener,
check to see if the garage door opens and closes.
If the garage door does not operate, identify if your garage
transmitter is of the “Rolling Code” type. Press and hold the
programmed HomeLink
\b button. The garage door has the
rolling code feature if the indicator light (on the HomeLink\b)
flashes rapidly and then remains lit after 2 seconds. If your
garage transmitter is the “Rolling Code” type, proceed to the
heading “Programming a rolling code system”. 6. Repeat steps 2 through 5 for each remaining HomeLink
\b
button to program another device.
Programming a rolling code system
If your device is “Rolling Code” equipped, it is necessary
to follow steps 1 through 4 under the heading
“Programming the HomeLink
\b” before proceeding with
the steps listed below.
1. Locate the “training” button on the ceiling mounted garage
door opener motor. The exact location and color of the button
may vary by brand of garage door opener. Refer to the owner’s
guide supplied by the garage door opener manufacturer for the
location of this “training” button.
2. Press the “training” button on the ceiling mounted garage
door opener motor.
Following this step, you have 30 seconds in which to initiate
step 3 below.
3. Press and release the vehicle’s programmed HomeLink
\b
button twice. The garage door may open. If the door does
open, the programming process is complete. If the door does
not open, press and release the button a third time. This third
press and release will complete the programming process by
opening the garage door.
The ceiling mounted garage door opener motor should now
recognize the HomeLink
\b unit and be able to activate the
garage door up/down.

INTERIOR EQUIPMENT
1244. Repeat steps 1 through 3 for each remaining HomeLink
\b
button to program another rolling code system.
Programming an entrance gate /
Programming all devices in the Canadian
market
1. Decide which of the 3 HomeLink\b buttons you want to
program.
2. Place your hand −held gate/device transmitter 25 to 75 mm
(1 to 3 in.) away from the surface of the HomeLink
\b.
Keep the indicator light on the HomeLink
\b in view while
programming.
3. Press and hold the selected HomeLink
\b button.
4. Continuously press and release (cycle) the hand−held
gate/device transmitter button every two seconds until step 5
is complete.
5. When the indicator light on the HomeLink
\b changes from a
slow to a rapid flash after 20 seconds, you can release both
buttons.
6. Test the operation of the HomeLink
\b by pressing the newly
programmed button. Check to see if the gate/device operates
correctly.
7. Repeat steps 1 through 6 for each remaining HomeLink
\b
button to program another device.
Programming other devices
To program other devices such as home security systems,
home door locks or lighting, contact your authorized Lexus
dealer for assistance.
Reprogramming a button
Individual HomeLink\b
buttons c annot be erased, however, to
reprogram a single button, follow the procedure “Programming
the HomeLink
\b”.
(b) Operating the HomeLink\b
To operate the HomeLink\b, press the appropriate HomeLink\b
button to activate the programmed device. The HomeLink\b
indicator light should come on. The HomeLink\b continues to
send the signal for up to 20 seconds as long as the button is
pressed.

INTERIOR EQUIPMENT
125
(c) Erasing the entire HomeLink\b memory
(all three programs)
To erase all previously programmed codes at one time, press
and hold down the 2 outside buttons for 20 seconds until the
indicator light flashes.
If you sell your vehicle, be sure to erase the programs stored
in the HomeLink
\b memory.
CAUTION
 When programming the HomeLink\b Universal
Transceiver, you may be operating a garage door or
other device. Make sure people and objects are out
of the way of the garage door or other device to
prevent potential harm or damage.
 Do not use this HomeLink
\b Universal Transceiver
with any garage door opener that lacks the safety
stop and reverse feature as required by federal safety
standards. (This includes any garage door opener
model manufactured before April 1, 1982.) A garage
door opener which cannot detect an object
(signaling the door to stop and reverse), does not
meet current federal safety standards. Using a
garage door opener without these features increases
risk of serious injury or death.
This device complies with Part 15 of the FCC Rules
and with RSS− 210 of the IC Rules.
Operation is subject to the following two conditions: (1)
This device may not cause harmful interference, and
(2) this device must accept any interference received,
including interference that may cause undesired
operation.
WARNING: This transmitter has been tested and
complies with FCC and IC rules. Changes or
modifications not expressly approved by the party
responsible for compliance could void the user’s
authority to operate the device.